The e500 MMU init code previously assumed KERNELBASE always equaled
PAGE_OFFSET and PHYSICAL_START was 0. This is useful for kdump
support as well as asymetric multicore.
For the initial kdump support the secondary kernel will run at 32M
but need access to all of memory so we bump the initial TLB up to
64M. This also matches with the forth coming ePAPR spec.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Don't depend on the reg property as a way to determine the base
of the immr space. The reg property might be defined differently for
different SoC families.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update the MPC8610 HPCD files to support the audio driver. Update
booting-without-of.txt with information on the SSI device.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
IPIC is not just for 83xx anymore so make it a separate config option.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added ipic_info entries for vectors used by 512x that
were previously unused by 83xx.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Synchronize it to the definition in include/math-emu/op-4.h for short term.
Signed-off-by: Liu Yu <Yu.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add in missing of_node_put() after cpm2_pic_init(). This and other coding
style cleanups as suggested by Stephen Rothwell.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for UART serial ports using a Freescale QUICCEngine. Update
booting-without-of.txt to define new properties for a QE UART node. Update
the MPC8323E-MDS device tree to add UCC5 as a UART. Update the QE library
to support slow UCC devices and modules.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Define the layout of a binary blob that contains a QE firmware and instructions
on how to upload it. Add function qe_upload_firmware() to parse the blob
and perform the actual upload. Fully define 'struct rsp' in immap_qe.h to
include the actual RISC Special Registers. Added description of a new
QE firmware node to booting-without-of.txt.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fixed-link says: register new "Fixed/emulated PHY", i.e. PHY that
not connected to the real MDIO bus.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
...thus use fixed-link to register proper "Fixed PHY"
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds localbus and pata nodes to use CF IDE interface
on MPC8349E-mITX boards.
Patch also adds code to probe localbus.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove device_type = "usb" for 83xx SoC USB controller
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add chip specific and board specific initialization for MPC837x USB.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The ULI based boards had the interrupt maps for USB on the ULI incorrectly
set.
Also, the MPC8572DS was missing the interrupt-map-mask for the 3rd PCIe
controller.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to set the mac address given the alias for the device.
Removes the need for having a linux,network-index property.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mpic_map() and __mpic_map_mmio() need to use phys_addr_t for the
physical address they are passed.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current PCI code for Freescale 85xx/86xx was treating the virtual
P2P PCIe bridge as a transparent bridge. Rather than doing that fixup
the virtual P2P bridge by copying the resources from the PHB.
Also, fixup a bit of the code for dealing with resource_size_t being
64-bits and how we set ATMU registers for >4G.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For transparent P2P bridges the first 3 resources may get set from based on
BAR registers and need to get fixed up. Where as the remainder come from the
parent bus and have already been fixed up.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The fixup code that handles the case for PowerMac's that leave bridge
windows open over an inaccessible region should only be applied to
memory resources (IORESOURCE_MEM). If not we can get it trying to fixup
IORESOURCE_IO on some systems since the other conditions that are used to
detect the case can easily match for IORESOURCE_IO.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There were several issues if a memreserve range existed and happened
to be in highmem:
* The bootmem allocator is only aware of lowmem so calling
reserve_bootmem with a highmem address would cause a BUG_ON
* All highmem pages were provided to the buddy allocator
Added a lmb_is_reserved() api that we now use to determine if a highem
page should continue to be PageReserved or provided to the buddy
allocator.
Also, we incorrectly reported the amount of pages reserved since all
highmem pages are initally marked reserved and we clear the
PageReserved flag as we "free" up the highmem pages.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Using 64k pages on 64-bit PowerPC systems makes life difficult for
emulators that are trying to emulate an ISA, such as x86, which use a
smaller page size, since the emulator can no longer use the MMU and
the normal system calls for controlling page protections. Of course,
the emulator can emulate the MMU by checking and possibly remapping
the address for each memory access in software, but that is pretty
slow.
This provides a facility for such programs to control the access
permissions on individual 4k sub-pages of 64k pages. The idea is
that the emulator supplies an array of protection masks to apply to a
specified range of virtual addresses. These masks are applied at the
level where hardware PTEs are inserted into the hardware page table
based on the Linux PTEs, so the Linux PTEs are not affected. Note
that this new mechanism does not allow any access that would otherwise
be prohibited; it can only prohibit accesses that would otherwise be
allowed. This new facility is only available on 64-bit PowerPC and
only when the kernel is configured for 64k pages.
The masks are supplied using a new subpage_prot system call, which
takes a starting virtual address and length, and a pointer to an array
of protection masks in memory. The array has a 32-bit word per 64k
page to be protected; each 32-bit word consists of 16 2-bit fields,
for which 0 allows any access (that is otherwise allowed), 1 prevents
write accesses, and 2 or 3 prevent any access.
Implicit in this is that the regions of the address space that are
protected are switched to use 4k hardware pages rather than 64k
hardware pages (on machines with hardware 64k page support). In fact
the whole process is switched to use 4k hardware pages when the
subpage_prot system call is used, but this could be improved in future
to switch only the affected segments.
The subpage protection bits are stored in a 3 level tree akin to the
page table tree. The top level of this tree is stored in a structure
that is appended to the top level of the page table tree, i.e., the
pgd array. Since it will often only be 32-bit addresses (below 4GB)
that are protected, the pointers to the first four bottom level pages
are also stored in this structure (each bottom level page contains the
protection bits for 1GB of address space), so the protection bits for
addresses below 4GB can be accessed with one fewer loads than those
for higher addresses.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix typo in arch/powerpc/boot/flatdevtree_env.h.
There is no Documentation/networking/ixgbe.txt.
README.cycladesZ is now in Documentation/.
wavelan.p.h is now in drivers/net/wireless/.
HFS.txt is now Documentation/filesystems/hfs.txt.
OSS-files are now in sound/oss/.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no reason to have separate defconfigs for each mpc5200 board.
Instead, here is a common defconfig that can be used for all supported
platforms.
Merging the defconfigs means there are fewer configuration to test when
compile testing all of arch/powerpc and should make support easier.
Supported boards:
Lite5200(b), Efika, TQM5200, CM5200, MotionPro
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds support for 'mpc5200-simple-platform' compatible
boards which do not need a platform specific setup. Such boards
are supported assuming the following:
- GPIO pins are configured by the firmware,
- CDM configuration (clocking) is setup correctly by firmware,
- if the 'fsl,has-wdt' property is present in one of the
gpt nodes, then it is safe to use such gpt to reset the board,
- PCI is supported if enabled in the kernel configuration
and if there is a PCI bus node defined in the device tree.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add device tree source file for Promess Motion-PRO board.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add device tree source file for CM5200 board.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add device tree source file for TQ Components TQM5200 board.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
mpc5200 platform code defines a bunch of map functions which duplicate the
functionality of of_iomap(). Remove them and use of_iomap() instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch moves a generic pci init code from lite5200
platform file to a common mpc52xx_setup_pci() routine
and adds additional compatibility property verification.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Define MPC52xx specific device id list, add new
'fsl,lpb' compatible id for LocalPlus Bus.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Also check that __NR_syscalls has been updated appropriately.
Hopefully this will catch any out of order additions to the
table in the future.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds the hugepagesz boot-time parameter for ppc64. It lets one
pick the size for huge pages. The choices available are 64K and 16M
when the base page size is 4k. It defaults to 16M (previously the
only only choice) if nothing or an invalid choice is specified.
Tested 64K huge pages successfully with the libhugetlbfs 1.2.
Signed-off-by: Jon Tollefson <kniht@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update .gitignore as needed by dtc addition.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
xlate_iomm_address() really wants the ds_addr to pass to the HV, so store
that value (instead of the BAR number) when we allocate the device bars.
This is not a fast path, so we can look up the device_node property
there instead of using the bussubno field of the pci_dn.
The other user of iseries_ds_addr() was already scanning the device tree,
so looking up a property will not slow it down any more.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Scott Wood