removed some needless checks and also corrected bug in lp486e (dmi was passed
instead of dmi->dmi_addr)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the bus-error reporting configurable and allows to
retrieve the CAN TX and RX bus error counters via netlink interface.
I have added support for the SJA1000. The TX and RX bus error counters
are also copied to the data fields 6..7 of error messages when state
changes are reported.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt)
Convert logging messages to pr_<level> and netdev_<level>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert CH_<level> and CH_DBG uses to pr_<level> and netif equivalents
Remove CH_<level> and CH_DBG macro definitions
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Samll cleanup in drivers/isdn/gigaset/capi.c where own implementation of
isxdigit() has been changed to kernel native one.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve readability of the Gigaset driver's kernel messages by
removing a few unnecessary messages and limiting the emission
of some debug messages more narrowly.
Impact: logging
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Copy the mechanism from ser_/usb_gigaset to avoid producing
spurious empty responses for CR/LF sequences from the device.
Add a comment in all drivers documenting that behaviour.
Correct an off by one error that might result in a one byte
buffer overflow when receiving an unexpectedly long reply.
Impact: minor bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clarify the non-support by isdnlog, and propose a better standard
debug mask.
Impact: Documentation
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_carrier_on() and netif_carrier_off() should be called from
link status interrupt handler
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just pass in the entire repl struct. In case of a new table (e.g.
ip6t_register_table), the repldata has been previously filled with
table->name and table->size already (in ip6t_alloc_initial_table).
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The macro is replaced by a list.h-like foreach loop. This makes
the code more inspectable.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The macro is replaced by a list.h-like foreach loop. This makes
the code much more inspectable.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Traffic (tcp) doesnot start on a vlan interface when gro is enabled.
Even the tcp handshake was not taking place.
This is because, the eth_type_trans call before the netif_receive_skb
in napi_gro_finish() resets the skb->dev to napi->dev from the previously
set vlan netdev interface. This causes the ip_route_input to drop the
incoming packet considering it as a packet coming from a martian source.
I could repro this on 2.6.32.7 (stable) and 2.6.33-rc7.
With this fix, the traffic starts and the test runs fine on both vlan
and non-vlan interfaces.
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we clone the SP, we should also clone the mark.
Useful for socket based SPs.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
A rule with a zero hit_count will always match.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>
e->index overflows e->stamps[] every ip_pkt_list_tot packets.
Consider the case when ip_pkt_list_tot==1; the first packet received is stored
in e->stamps[0] and e->index is initialized to 1. The next received packet
timestamp is then stored at e->stamps[1] in recent_entry_update(),
a buffer overflow because the maximum e->stamps[] index is 0.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>
The netif_wake_queue() is called correctly (i.e. only on !txfull
condition) from txdone routine. So Unconditional call to the
netif_wake_queue() here is wrong. This might cause calling of
start_xmit routine on txfull state and trigger BUG_ON.
This bug does not happen when NAPI disabled. After txdone there
must be at least one free tx slot. But with NAPI, this is not
true anymore and the BUG_ON can hits on heavy load.
In this driver NAPI was enabled on 2.6.33-rc1 so this is
regression from 2.6.32 kernel.
Reported-by: Ralf Roesch <ralf.roesch@rw-gmbh.de>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new vid/pid to the cdc_ether whitelist.
Device added:
- Ericsson Mobile Broadband variant C3607w
Signed-off-by: Torgny Johansson <torgny.johansson@gmail.com>
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Morton wrote:
>> >From ip-sysctl.txt file in kernel documentation I can see following description
>> for max_addresses:
>> max_addresses - INTEGER
>> Number of maximum addresses per interface. 0 disables limitation.
>> It is recommended not set too large value (or 0) because it would
>> be too easy way to crash kernel to allow to create too much of
>> autoconfigured addresses.
^^^^^^^^^^^^^^
>> If this parameter applies only for auto-configured IP addressed, please state
>> it more clearly in docs or rename the parameter to show that it refers to
>> auto-configuration.
It did mention autoconfigured in the text, but the below makes it more obvious.
More clearly document IPv6 max_addresses parameter.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for error return from pci_map_single/pci_map_page and clean up.
With this and the previous patch the driver was able to handle a significant
percentage of errors (I set the fault injection rate to 10% and could still
download large files at a reasonable speed).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ability for netlink userspace to manipulate the SPD
and manipulate the mark, retrieve it and get events with a defined
mark, etc.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ability for netlink userspace to manipulate the SAD
and manipulate the mark, retrieve it and get events with a defined
mark.
MIGRATE may be added later.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
pass mark to all SP lookups to prepare them for when we add code
to have them search.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
pass mark to all SA lookups to prepare them for when we add code
to have them search.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic structuring and accessors for xfrm mark
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of custom locking that was using wait queue, lock, and atomic
to basically build a queued mutex. Use RCU for read side.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert AF_PACKET to use RCU, eliminating one more reader/writer lock.
There is no need for a real sk_del_node_init_rcu(), because sk_del_node_init
is doing the equivalent thing to hlst_del_init_rcu already; but added
some comments to try and make that obvious.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many usages of seq_file use RCU protected lists, so non RCU
iterators will not work safely.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the suspend and resume implementation in the HECC (CAN)
driver.
Signed-off-by: K R Baalaaji <krbaalaaji@ti.com>
Signed-off-by: Sriramakrishnan <srk@ti.com>
Acked-by: Anant Gole <anantgole@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Rewrite the outdated help texts for config options ISDN and ISDN_CAPI.
2. The MISDN config option appeared between ISDN_I4L and the I4L hardware
driver options; move it to a less irritating place.
3. HYSDN is not in fact an I4L driver, and needn't depend on ISDN_I4L, so
move it from the I4L section to the general section.
4. ISDN_HDLC is now also used by drivers outside I4L. Move it from the
I4L section to the general section, too.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Dillow took my suggestions and improved on them.
Here is this latest version.
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Remove #define ERR_PFX
Remove now unused member name from struct typhoon
Use pr_<level>
Use netdev_<level>
Coalesce long formats
Remove version information
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David Dillow <dave@thedillows.org>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: David Dillow <dave@thedillows.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conversion in bf0dcbd929 missed the
new allocation in b44_rx.
This patch was used in OpenWRT for a long time.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do a PHY reset to test if there is an active phy and set the PHY address
to B44_PHY_ADDR_NO_PHY in case of an not active phy. This is needed for
the Linksys WRTSL54GS and Asus WL-500W.
This patch was used in OpenWRT for a long time.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the 82576NS Serdes adapter to the existing pci
quirk for 82576 parts.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PowerPC architecture does not require loads to independent bytes to be
ordered without adding an explicit barrier.
In ixgbe_clean_rx_irq we load the status bit then load the packet data.
With packet split disabled if these loads go out of order we get a
stale packet, but we will notice the bad sequence numbers and drop it.
The problem occurs with packet split enabled where the TCP/IP header and data
are in different descriptors. If the reads go out of order we may have data
that doesn't match the TCP/IP header. Since we use hardware checksumming this
bad data is never verified and it makes it all the way to the application.
This bug was found during stress testing and adding this barrier has been shown
to fix it.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts mwl8k to use the new station
add/remove callbacks instead of using the
old sta_notify callback.
The new callbacks can sleep, so a lot of
code can be removed now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jiri Pirko