Update the ATA passthru protocol numbers according to the new spec.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The controller is not reporting an unlawful type, it is reporting an
invalid type. Illegal specifically means "prohibited by law"
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ata IRQ ack functions are only used when debugging. Unfortunately
almost every controller that calls them can cause crashes in some
configurations as there are missing checks for bmdma presence.
In addition ata_port_start insists of installing DMA buffers and pad
buffers for controllers regardless. The SFF controllers actually need to
make that decision dynamically at controller setup time and all need the
same helper - so we add ata_sff_port_start. Future patches will switch
the SFF drivers to use this.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hw_sata_spd_limit used to be incorrectly initialized to zero instead
of UINT_MAX if SPD is zero in SControl register. This breaks PHY
speed down. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For ATA/CFA devices, libata prints out the device model and firmware revision.
Do the same for ATAPI devices.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Most drivers don't seem to fill out the host->irq field, resulting in the
wrong (no) irq being reported at probe time. For example, sil24 on my system:
ata1: SATA max UDMA/100 cmd 0xd00008009001f000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata2: SATA max UDMA/100 cmd 0xd000080090021000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
Since they're allocated and set up in ata_host_activate(), just save
them away there.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch has removed unused variable in pata_ispnp.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[CIPSO]: Fix several unaligned kernel accesses in the CIPSO engine.
[NetLabel]: consolidate the struct socket/sock handling to just struct sock
[IPV4]: Do not remove idev when addresses are cleared
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Handle PCI bridges without 'ranges' property.
[SPARC64]: Include <linux/rwsem.h> instead of <asm/rwsem.h>.
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
OHCI: Fix machine check in ohci_hub_status_data
USB: Fix up bogus bInterval values in endpoint descriptors
USB: cxacru: ignore error trying to start ADSL in atm_start
USB: cxacru: create sysfs attributes in atm_start instead of bind
USB: cxacru: add Documentation file
USB: UNUSUAL_DEV: Sync up some reported devices from Ubuntu
USB: usb gadgets avoid le{16,32}_to_cpup()
usblp: Don't let suspend to kill ->used
USB: set default y for CONFIG_USB_DEVICE_CLASS
Prevent <linux/console_struct.h> from being included more than once,
otherwise you get a redefinition error if you happen to include
<linux/vt_kern.h> first.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This version brings a some new tests, and a host of changes to fix
false positives, of particular note:
- check for and report #if 0
- extend checking of line lengths and spacing for .pl, .sh etc
- extends the pointer type checks to multiple levels
- updates printk handling to track newlines
- adds a wrapped patch detector
- drops the leading component of the filenames
- extends switch indent handling to switch statmentes rooted in
the context
- adds foo * bar single pointer checks
This version of checkpatch.pl can be found at the following URL:
http://www.shadowen.org/~apw/public/checkpatch/checkpatch.pl-0.04
Full Changelog:
Andy Whitcroft (16):
allow checking line lengths and spacing on other source files
clean up that whitespace
sanitise the input line standardising the content of quotes
clean up pointer type * and space checks
fix up the sanitiser so it maintains the line length
apply the printk facility checks only to the first printk in a set
switch/case indent checks may anchor in the context
add a wrapped patch detector
put the #ifdef in C file checks on ice
asm volatile is acceptable
check for and report #if 0
drop the leading component of the filename as patches are -p1
use the original line when reporting operator errors
correct spelling of Joel's name
Version: 0.04
add support for struct foo * bar checks
Geert Uytterhoeven (1):
Fix checkpatch.pl name in usage template
Randy Dunlap (1):
checkpatch: produce fewer lines of output
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a prefix string parameter. Callers are responsible for any string
length/alignment that they want to see in the output. I.e., callers should
pad strings to achieve alignment if they want that.
Add rowsize parameter. This is the number of raw data bytes to be printed
per line. Must be 16 or 32.
Add a groupsize parameter. This allows callers to dump values as 1-byte,
2-byte, 4-byte, or 8-byte numbers. Default is 1-byte numbers. If the
total length is not an even multiple of groupsize, 1-byte numbers are
printed.
Add an "ascii" output parameter. This causes ASCII data output following
the hex data output.
Clean up some doc examples.
Align the ASCII output on all lines that are produced by one call.
Add a new interface, print_hex_dump_bytes(), that is a shortcut to
print_hex_dump(), using default parameter values to print 16 bytes in
byte-size chunks of hex + ASCII output, using printk level KERN_DEBUG.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The UFS entry was misformatted
The NEC V850 links are all broken
The Berkshire watchdog links are all broken
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Produce one less line of output per flagged incident.
Change this:
use tabs not spaces
PATCH: /home/rddunlap/arcmsr1200014.patch4:756:
FILE: b/drivers/scsi/arcmsr/arcmsr_hba.c:1843:
+ return PCI_ERS_RESULT_NEED_RESET;$
to this:
use tabs not spaces
#756: FILE: b/drivers/scsi/arcmsr/arcmsr_hba.c:1843:
+ return PCI_ERS_RESULT_NEED_RESET;$
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes MAINTAINERS to reflect the new location of the reiserfs
development mailing list. The old list forwards to the new one.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We aren't sampling for holes in memory. Thus we encounter a section hole
with empty section map pointer for SPARSEMEM and OOPs for show_mem. This
issue has been seen in 2.6.21, current git and current mm. The patch below
is for mainline and mm. It was boot tested for SPARSEMEM, current VMEMMAP
of Andy's in mm ml and DISCONTIGMEM. A slightly different patch will be
posted to stable for 2.6.21.
Previous to commit f0a5a58aa8 memory_present
was called for node_start_pfn to node_end_pfn. This would cover the
hole(s) with reserved pages and valid sections. Most SPARSEMEM supported
arches do a pfn_valid check in show_mem before computing the page structure
address.
This issue was brought to my attention on IRC by Arnaldo Carvalho de Melo.
Thanks to Arnaldo for testing.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. New entries can be added to tsk->pi_state_list after task completed
exit_pi_state_list(). The result is memory leakage and deadlocks.
2. handle_mm_fault() is called under spinlock. The result is obvious.
3. results in self-inflicted deadlock inside glibc.
Sometimes futex_lock_pi returns -ESRCH, when it is not expected
and glibc enters to for(;;) sleep() to simulate deadlock. This problem
is quite obvious and I think the patch is right. Though it looks like
each "if" in futex_lock_pi() got some stupid special case "else if". :-)
4. sometimes futex_lock_pi() returns -EDEADLK,
when nobody has the lock. The reason is also obvious (see comment
in the patch), but correct fix is far beyond my comprehension.
I guess someone already saw this, the chunk:
if (rt_mutex_trylock(&q.pi_state->pi_mutex))
ret = 0;
is obviously from the same opera. But it does not work, because the
rtmutex is really taken at this point: wake_futex_pi() of previous
owner reassigned it to us. My fix works. But it looks very stupid.
I would think about removal of shift of ownership in wake_futex_pi()
and making all the work in context of process taking lock.
From: Thomas Gleixner <tglx@linutronix.de>
Fix 1) Avoid the tasklist lock variant of the exit race fix by adding
an additional state transition to the exit code.
This fixes also the issue, when a task with recursive segfaults
is not able to release the futexes.
Fix 2) Cleanup the lookup_pi_state() failure path and solve the -ESRCH
problem finally.
Fix 3) Solve the fixup_pi_state_owner() problem which needs to do the fixup
in the lock protected section by using the in_atomic userspace access
functions.
This removes also the ugly lock drop / unqueue inside of fixup_pi_state()
Fix 4) Fix a stale lock in the error path of futex_wake_pi()
Added some error checks for verification.
The -EDEADLK problem is solved by the rtmutex fixups.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexey Kuznetsov found some problems in the pi-futex code.
One of the root causes is:
When a wakeup happens, we do not to stop the chain walk so we follow a not
longer relevant locking chain.
Drop out when this happens.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexey Kuznetsov found some problems in the pi-futex code.
The major problem is a stale return value in rt_mutex_slowlock():
When the pi chain walk returns -EDEADLK, but the waiter was woken up during
the phases where the locks were dropped, the rtmutex could be acquired, but
due to the stale return value -EDEADLK returned to the caller.
Reset the return value in the retry path.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sata_promise uses two different command modes - packet and TF. Packet mode
is intelligent low-overhead mode while TF is the same old taskfile
interface. As with other advanced interface (ahci/sil24),
ATA_TFLAG_POLLING has no effect in packet mode. However, PIO commands are
issued using TF interface in polling mode, so pdc_interrupt() considers
interrupts spurious if ATA_TFLAG_POLLING is set.
This is broken for polling NODATA commands because command is issued using
packet mode but the interrupt handler ignores it due to ATA_TFLAG_POLLING.
Fix pdc_qc_issue_prot() such that ATA/ATAPI NODATA commands are issued
using TF interface if ATA_TFLAG_POLLING is set.
This patch fixes detection failure introduced by polling SETXFERMODE.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__exit function is used by both init and exit routines, so it cannot
be marked __init. (from allyesconfig)
WARNING: drivers/built-in.o(.text+0x9b83cf): Section mismatch: reference to .exit.text: (between 'divasfunc_exit' and 'didd_callback')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Karsten Keil <kkeil@suse.de>
Acked-by: Armin Schindler <armin@melware.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include linux/kernel.h wherever simple_strtoul is used. This kills a
compile warning in stderr_console.c and potential ones in the other files.
This also fixes a bunch of style violations in exitcode.c.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
do not return 0 in one case and return proper values in other 2.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
this causes oops, because pci probe function calls tty_register_device for
each device found. Thanks to Ingo.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: "Ingo Korb" <ingo@akana.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since it's not neccesary to have MAX_PANELS on the card, don't fail to let
users use this card even in this case. Stop the testing for loop instead.
Thanks to Ingo.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: "Ingo Korb" <ingo@akana.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Force KERNEL_STACK_ORDER to be at least 1 on UML/x86_64, to avoid overflows.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of returning the smallest available object return ZERO_SIZE_PTR.
A ZERO_SIZE_PTR can be legitimately used as an object pointer as long as it
is not deferenced. The dereference of ZERO_SIZE_PTR causes a distinctive
fault. kfree can handle a ZERO_SIZE_PTR in the same way as NULL.
This enables functions to use zero sized object. e.g. n = number of objects.
objects = kmalloc(n * sizeof(object));
for (i = 0; i < n; i++)
objects[i].x = y;
kfree(objects);
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix various bits of obviously-busted code which we're not happening to
compile, due to ifdefs.
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Andi Kleen <ak@suse.de>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cache_free_alien must be called regardless if we use alien caches or not.
cache_free_alien() will do the right thing if there are no alien caches
available.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Pekka J Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap reports that a tmpfs, mounted with NUMA mpol= specifying an
offline node, crashes as soon as data is allocated upon it. Now restrict it
to online nodes, where before it restricted to MAX_NUMNODES.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Tested-and-acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that deprecated functions are detected out of
Documentation/feature-removal-schedule.txt update this to include
kernel_thread.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Explain what we use Acked-by: for, and how it differs from Signed-off-by:
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kernel on-demand loop device instantiation breaks several user space
tools as the tools are not ready to cope with the "on-demand feature". Fix
it by instantiate default 8 loop devices and also reinstate max_loop module
parameter.
Signed-off-by: Ken Chen <kenchen@google.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Report the correct errno for out of memory debug output in binfmt_flat.c
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The coldfire timer runs from 0 to TRR included, then 0 again and so on. It
counts thus actually TRR + 1 steps for 1 tick, not TRR. Fix that.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This version brings a host of changes to cure false positives and
bugs detected on patches submitted to lkml and -mm. It also brings
a number of new tests in response to reviews, of particular note:
- catch use of volatile
- allow deprecated functions to be listed in feature-removal-schedule.txt
- warn about #ifdef's in c files
- check that spinlock_t and struct mutex use is commented
- report on architecture specific defines being used
- report memory barriers without an associated comment
Full changelog:
catch use of volatile
convert other quoted string checks to common routine
alloc deprecated functions to be listed in feature-removal-schedule.txt
split out the line length and indent for each line
improve switch block handling
handle GNU diff context lines with no leading space
warn about #ifdef's in c files
tidy up tests for signed-off-by using raw mode
check that spinlock_t and struct mutex use is commented
syntax checks for open brace placement may drop off the bottom of hunk
report memory barriers without an associated comment
when a sign off is present but ugly do not report it missing
do not mistake bitfield definitions for indented labels
report on architecture specific defines being used
major update to the operator checks
prevent switch/if/while etc matching foo_switch
generify assignement in condition error message
introduce an operator context marker
Version: 0.03
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as901) fixes an oversight in ohci-hcd. The
hub_status_data routine must not try to access the controller's
memory-mapped registers if the controller is in a low-power state;
such attempts will cause a crash on some architectures (such as PPC).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as904) adds code to check for endpoint descriptor bInterval
values outside the legal limits. Illegal values are set to 32 ms, which
seems like a reasonable default.
This fixes Bugzilla #8432.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The sysfs adsl_status attribute ignores (aside from returning -EIO to the
user) any error sending a START/STOP command to the device and there is at
least one firmware which never sends a response but appears to work
regardless. Therefore atm_start should also continue if an error is received
so that such firmware is usable.
The official Conexant driver doesn't expect a reply either but this is for
another device (E2 router) and a commonly used firmware does respond.
Also, there is no point in changing -ECONNRESET to -ETIMEDOUT since nothing
ever checks for either of these values.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@math.u-psud.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since usbatm doesn't set the usb_interface driver data until after calling
bind and heavy_init, it would be NULL when the sysfs attributes are read.
Reading the MAC address from atm_dev before atm_dev exists would have been
be possible too.
Calling create_device_file in atm_start will avoid this problem, and the
data is useless until the first status poll runs. However, it must be
ready before a status poll does a printk on line status change otherwise
userspace could react before the files exist.
For completeness I've moved remove_device_file to atm_stop so it's not
called in unbind when it's not needed. There's no point starting ADSL if
atm_start could still fail either.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@math.u-psud.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The sysfs attributes for exposing cxacru statistics/status information with
possible values is now explained in Documentation/networking/cxacru.txt
including information on the writable adsl_state attribute's commands and a
sample of the kernel log format.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@math.u-psud.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
UNUSUAL_DEV: Sync up some reported devices from Ubuntu
Various unusual dev entries accumulated from Ubuntu bug reports.
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Albert Lee