This patch is based off "xen dom0: Set up basic IO permissions for dom0."
by Juan Quintela <quintela@redhat.com>.
On AMD machines when we boot the kernel as Domain 0 we get this nasty:
mapping kernel into physical memory
Xen: setup ISA identity maps
about to get started...
(XEN) traps.c:475:d0 Unhandled general protection fault fault/trap [#13] on VCPU 0 [ec=0000]
(XEN) domain_crash_sync called from entry.S
(XEN) Domain 0 (vcpu#0) crashed on cpu#0:
(XEN) ----[ Xen-4.1-101116 x86_64 debug=y Not tainted ]----
(XEN) CPU: 0
(XEN) RIP: e033:[<ffffffff8130271b>]
(XEN) RFLAGS: 0000000000000282 EM: 1 CONTEXT: pv guest
(XEN) rax: 000000008000c068 rbx: ffffffff8186c680 rcx: 0000000000000068
(XEN) rdx: 0000000000000cf8 rsi: 000000000000c000 rdi: 0000000000000000
(XEN) rbp: ffffffff81801e98 rsp: ffffffff81801e50 r8: ffffffff81801eac
(XEN) r9: ffffffff81801ea8 r10: ffffffff81801eb4 r11: 00000000ffffffff
(XEN) r12: ffffffff8186c694 r13: ffffffff81801f90 r14: ffffffffffffffff
(XEN) r15: 0000000000000000 cr0: 000000008005003b cr4: 00000000000006f0
(XEN) cr3: 0000000221803000 cr2: 0000000000000000
(XEN) ds: 0000 es: 0000 fs: 0000 gs: 0000 ss: e02b cs: e033
(XEN) Guest stack trace from rsp=ffffffff81801e50:
RIP points to read_pci_config() function.
The issue is that we don't set IO permissions for the Linux kernel early enough.
The call sequence used to be:
xen_start_kernel()
x86_init.oem.arch_setup = xen_setup_arch;
setup_arch:
- early_cpu_init
- early_init_amd
- read_pci_config
- x86_init.oem.arch_setup [ xen_arch_setup ]
- set IO permissions.
We need to set the IO permissions earlier on, which this patch does.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Now that the balloon driver doesn't stumble over non-RAM pages, we
can enable the extra space for ballooning.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
If the user specifies mem= on the kernel command line, some or all
of the extra memory E820 region may be clipped away, so make sure
we don't try to add more extra memory than exists in E820.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Add extra pages in the pseudo-physical address space to the balloon
so we can extend into them later.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
The per-cpu event channel masks can be updated unlocked from multiple
CPUs, so use the locked variant.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
To bind all event channels to CPU#0, it is not sufficient to set all
of its cpu_evtchn_mask[] bits; all other CPUs also need to get their
bits cleared. Otherwise, evtchn_do_upcall() will start handling
interrupts on CPUs they're not intended to run on, which can be
particularly bad for per-CPU ones.
[ linux-2.6.18-xen.hg 7de7453dee36 ]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
This hypercall allows Xen to specify a non-default location for the
machine to physical mapping. This capability is used when running a 32
bit domain 0 on a 64 bit hypervisor to shrink the hypervisor hole to
exactly the size required.
[ Impact: add Xen hypercall definitions ]
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
We already deliberately setup a 1-1 P2M for the region up to 1M in
order to allow code which assumes this region is already mapped to
work without having to convert everything to ioremap.
Domain 0 should not return any apparently unused memory regions
(reserved or otherwise) in this region to Xen since the e820 may not
accurately reflect what the BIOS has stashed in this region.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
sizeof(pmd_t *) is 4 bytes on 32-bit PAE leading to an allocation of
only 2048 bytes. The correct size is sizeof(pmd_t) giving us a full
page allocation.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
and branch 'for-linus' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm
* 'for-linus' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
xen: register xen pci notifier
xen: initialize cpu masks for pv guests in xen_smp_init
xen: add a missing #include to arch/x86/pci/xen.c
xen: mask the MTRR feature from the cpuid
xen: make hvc_xen console work for dom0.
xen: add the direct mapping area for ISA bus access
xen: Initialize xenbus for dom0.
xen: use vcpu_ops to setup cpu masks
xen: map a dummy page for local apic and ioapic in xen_set_fixmap
xen: remap MSIs into pirqs when running as initial domain
xen: remap GSIs as pirqs when running as initial domain
xen: introduce XEN_DOM0 as a silent option
xen: map MSIs into pirqs
xen: support GSI -> pirq remapping in PV on HVM guests
xen: add xen hvm acpi_register_gsi variant
acpi: use indirect call to register gsi in different modes
xen: implement xen_hvm_register_pirq
xen: get the maximum number of pirqs from xen
xen: support pirq != irq
* 'stable/xen-pcifront-0.8.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (27 commits)
X86/PCI: Remove the dependency on isapnp_disable.
xen: Update Makefile with CONFIG_BLOCK dependency for biomerge.c
MAINTAINERS: Add myself to the Xen Hypervisor Interface and remove Chris Wright.
x86: xen: Sanitse irq handling (part two)
swiotlb-xen: On x86-32 builts, select SWIOTLB instead of depending on it.
MAINTAINERS: Add myself for Xen PCI and Xen SWIOTLB maintainer.
xen/pci: Request ACS when Xen-SWIOTLB is activated.
xen-pcifront: Xen PCI frontend driver.
xenbus: prevent warnings on unhandled enumeration values
xenbus: Xen paravirtualised PCI hotplug support.
xen/x86/PCI: Add support for the Xen PCI subsystem
x86: Introduce x86_msi_ops
msi: Introduce default_[teardown|setup]_msi_irqs with fallback.
x86/PCI: Export pci_walk_bus function.
x86/PCI: make sure _PAGE_IOMAP it set on pci mappings
x86/PCI: Clean up pci_cache_line_size
xen: fix shared irq device passthrough
xen: Provide a variant of xen_poll_irq with timeout.
xen: Find an unbound irq number in reverse order (high to low).
xen: statically initialize cpu_evtchn_mask_p
...
Fix up trivial conflicts in drivers/pci/Makefile
* 'packaging' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
scripts/package: don't break if %{_smp_mflags} isn't set
kbuild, deb-pkg: Check if KBUILD_IMAGE exists before copying it
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (39 commits)
Revert "namespace: add source file location exceptions"
Coccinelle: Add contextual message
Coccinelle: Fix documentation
Coccinelle: Find doubled arguments to boolean or bit operators.
Coccinelle: Find nested lock+irqsave functions that use the same flags variables.
namespace: add source file location exceptions
scripts/extract-ikconfig: add support for bzip2, lzma and lzo
kbuild: check return value of asprintf()
scripts/namespace.pl: improve to get more correct results
scripts/namespace.pl: some bug fixes
scripts/namespace.pl: update file exclusion list
scripts/namespace.pl: fix wrong source path
Coccinelle: Use the -no_show_diff option for org and report mode
Coccinelle: Add a new mode named 'chain'
Coccinelle: Use new comment format to explain kfree.cocci
Coccinelle: Improve user information with a new kind of comment
Coccinelle: Update documentation
MAINTAINERS: Coccinelle: Update email address
Documentation/kbuild: modules.txt cleanup
Documentation/kbuild: major edit of modules.txt sections 5-8
...
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (38 commits)
kbuild: convert `arch/tile' to the kconfig mainmenu upgrade
README: cite nconfig
Revert "kconfig: Temporarily disable dependency warnings"
kconfig: Use PATH_MAX instead of 128 for path buffer sizes.
kconfig: Fix realloc usage()
kconfig: Propagate const
kconfig: Don't go out from read config loop when you read new symbol
kconfig: fix menuconfig on debian lenny
kbuild: migrate all arch to the kconfig mainmenu upgrade
kconfig: expand file names
kconfig: use the file's name of sourced file
kconfig: constify file name
kconfig: don't emit warning upon rootmenu's prompt redefinition
kconfig: replace KERNELVERSION usage by the mainmenu's prompt
kconfig: delay gconf window initialization
kconfig: expand by default the rootmenu's prompt
kconfig: add a symbol string expansion helper
kconfig: regen parser
kconfig: implement the `mainmenu' directive
kconfig: allow PACKAGE to be defined on the compiler's command-line
...
Fix up trivial conflict in arch/mn10300/Kconfig
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (73 commits)
power: Revert "power_supply: Mark twl4030_charger as broken"
mfd: Fix a memory leak when unload mc13xxx-core module
mfd: Fix resource reclaim for max8998
mfd: Remove unneeded ret value checking for max8998 register updates
mfd: Add free max8998->ono irq in max8998_irq_exit()
mfd: Fix resource reclaim in pcf50633_remove()
omap4: pandaboard: fix up mmc card detect logic
mfd: Fix ezx_pcap_probe error path
mfd: Fix off-by-one value range checking for tps6507x
mfd: Remove __devinitdata from tc6393xb_mmc_resources
mfd: Add WM831x SPI support
mfd: Factor out WM831x I2C I/O from the core driver
mfd: Remove DEBUG defines from mc13xxx-core
mfd: Fix jz4740_adc_set_enabled
mfd: Add TPS658621C device ID
mfd: Fix twl-irq function declaration warnings
regulator: max8998 BUCK1/2 voltage change with use of GPIOs
mfd: Voltages and GPIOs platform_data definitions for max8998
regulator: max8998 BUCK1/2 internal voltages and indexes defined
mfd: Support for ICs compliant with max8998
...
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
watchdog: iTCO_wdt.c: remove extra pci_dev_put()'s from init code
watchdog: add support for Broadcom BCM63xx built-in watchdog
watchdog: f71808e_wdt: add support for the F71889FG
watchdog: MachZ: fix debug macro
watchdog: it8712f_wdt: Add module parameter for alternative reset sources
watchdog: it8712f_wdt: Add comments for config/control register names
watchdog: it87_wdt: Add support for watchdogs with 8b timers
watchdog: it87_wdt: Add support for IT8720F watchdog
watchdog: Use static const char * const where possible
watchdog: iTCO_wdt: Cleanup warning messages
watchdog: iTCO_wdt: TCO Watchdog patch for Intel Patsburg DeviceIDs
The iTCO_wdt driver erroneously releases the pci_dev, and causes PCI hotremove
to fail because of an incorrect usage count.
The probe for this driver does a for_each_pci_dev() which gets a reference for
a pci_dev when iTCO_wdt_init() is successful. The for_each_pci_dev() loop
puts a reference for a pci_dev when iTCO_wdt_init() fails, so the
iTCO_wdt_init() does not need to do any pci_dev_put()'s.
The only pci_dev_put() that is required is in the iTCO_wdt_cleanup() function.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Properly free irq and unregister max8998->rtc device in
max8998_i2c_probe() error path and max8998_i2c_remove().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
i2c_smbus_write_byte_data() returns zero or negative value,
therefore no need to check if ret is greater than zero or not.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Calling sysfs_remove_group() to remove sysfs entries
and unregister bl_pdev in pcf50633_remove().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
For MMC1 Controller, card detect interrupt source is
twl6030 which is non-gpio. The card detect call back function provides
card present/absent status by reading MMC Control register present
on twl6030. This functionality was introduced in mfd tree on
track to kernel.org
Sync pandaboard to the same and make mmc work.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
return -ENOMEM if create_singlethread_workqueue failed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If bytes == (TPS6507X_MAX_REGISTER + 1), we have a buffer overflow when
doing memcpy(&msg[1], src, bytes).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This static struct resource tc6393xb_mmc_resources[] is used in resume function,
therefore the data can not be wiped after init.
Also, this causes a section mismatch.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Implement support for controlling WM831x and WM832x devices using SPI.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In preparation for the addition of SPI support for the WM831x move the I2C
specific code into a separate file with a separate Kconfig option so the
I2C support can be excluded from the build.
Also update the 1133-EV1 PMIC module support for SMDK6410 to use the new
symbol.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When enabled is false, clear BIT(engine) of JZ_REG_ADC_ENABLE register.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The interface for this device should be identical to that of the
TPS658521A.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixes following sparse warnings for twl4030 and twl6030 irq files.
drivers/mfd/twl4030-irq.c:783:5: warning: symbol 'twl4030_init_irq' was not
declared. Should it be static?
drivers/mfd/twl4030-irq.c:863:5: warning: symbol 'twl4030_exit_irq' was not
declared. Should it be static?
drivers/mfd/twl4030-irq.c:873:5: warning: symbol 'twl4030_init_chip_irq' was
not declared. Should it be static?
drivers/mfd/twl6030-irq.c:226:5: warning: symbol 'twl6030_init_irq' was not
declared. Should it be static?
drivers/mfd/twl6030-irq.c:290:5: warning: symbol 'twl6030_exit_irq' was not
declared. Should it be static?
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Tony Lindgren <tony@atomide.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
max8998_pmic_probe:
- modified to check if valid pins are defined at platform
data
- maximal voltage values (predefined at platform data) are uploaded to
max8998 device
max8998_set_voltage_buck:
- BUCK1/2 voltages change between values already defined
- Checks if valid GPIO pins are passed from platform data
- If requested voltage cannot be satisfied from already defined values,
then one of free slots is used
- Predefined maximum voltages (as defined at platform data) are always
available
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
BUCK1/2 internal voltages and indexes defined in the struct max8998_data
max_get_voltage_register now uses index values to chose proper register
More generic BUCK1/2 registers names provided
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The chip TRM documentation contradicts itself about this bit, page 174
of swcu050e says bit should be 0 for clear-on-read behavior, while
page 487 says it should be 1. Testing shows it should be 1, so set
the .set_cor flag accordingly. This is needed for upcoming BCI
charging driver to function.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When the cell data_size is 0, the resulting platform_data pointer will be
set to ZERO_SIZE_PTR. That could be misleading for device drivers running
a NULL check on thei platform_data pointer before dereferencing it.
Signed-off-by: Brian Harring <ferringb@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now that we have twl4030 charger driver, add back it's platform_data
(which was removed by f7ea2dc59e
as unused).
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The mfd driver for MC13783 recently got support for MC13892 and was
renamed accordingly from mc13783-core to mc13xxx-core. Do the same for
rtc-mc13783.
The only relevant change is to use platform id's to tell the platform bus
that this driver is responsible for mc13892-rtc devices, too.
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adding card detect callback function and card detect configuration
function for MMC1 Controller on OMAP4.
Card detect configuration function does initial configuration of the
MMC Control & PullUp-PullDown registers of Phoenix.
For MMC1 Controller, card detect interrupt source is
twl6030 which is non-gpio. The card detect call back function provides
card present/absent status by reading MMC Control register present
on twl6030.
Since OMAP4 doesn't use any GPIO line as used in OMAP3 for card detect,
the suspend/resume initialization which was done in omap_hsmmc_gpio_init
previously is moved to the probe thus making it generic for both OMAP3 &
OMAP4.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
mc13892 is the companion PMIC for Freescale's i.MX51. It's similar enough
to mc13782 to support it in a single driver.
This patch introduces enough compatibility cruft to keep all users of the
superseded mc13783 driver unchanged.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The last user is gone since v2.6.34-rc1~40
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The regulator driver was converted to get the needed data directly from
platform_data by
a10099b (regulator/mc13783: various cleanups)
so regulators and num_regulators can go away. Then apart from the flag
indicating that the adc does a conversion, flags is only a copy of the
flags member of platform_data. This flag isn't needed to be returned by
mc13783_get_flags, so mc13783_get_flags now gets the flags from
platform_data, too and the driver private member is renamed for clearity.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is needed for supporting the upcoming VX855 camera and OLPC DCON
drivers, as well as the advanced viafb features on non-OLPC hardware
based on this chip.
Based on earlier work by Harald Welte.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This device has GPIO, SPI and I2C capabilities.
The hardware can be found in the OLPC XO-1.5 laptop.
Based on earlier work by Harald Welte.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Konrad Rzeszutek Wilk