These headset jacks keep coming in on more and more platforms, and
it's possible I don't catch them all. Make it easier to test and
verify by making models.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just like the previous fix for LogitechHD Webcam c270 in commit
11e7064f35, c310 model also requires the
same workaround for avoiding the kernel warning.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59741
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MacBook Air 4,2 requires the whole default pin configuration table to
be overridden by the driver, as usual, as Apple's machines don't set
up properly after boot. Otherwise mic won't work, and other ill
effect may happen.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59381
Reported-and-tested-by: Peter John Hartman <peterjohnhartman@gmail.com>
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the Android firmware enables the audio interfaces in accessory
mode, it always declares in the control interface's baInterfaceNr array
that interfaces 0 and 1 belong to the audio function. However, the
accessory interface itself, if also enabled, already is at index 0 and
shifts the actual audio interface numbers to 1 and 2, which prevents the
PCM streaming interface from being seen by the host driver.
To get the PCM interface interface to work, detect when the descriptors
point to the (for this driver useless) accessory interface, and redirect
to the correct one.
Reported-by: Jeremy Rosen <jeremy.rosen@openwide.fr>
Tested-by: Jeremy Rosen <jeremy.rosen@openwide.fr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
They need these quirks to have headset mic support.
BugLink: https://bugs.launchpad.net/bugs/1189363
Tested-by: Shawn Wang <shawn.wang@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Another week, another batch of fixes for arm-soc platforms.
Again, nothing controversial. A few more than would be ideal, but all
are valid fixes. In particular the prima2 panic patch is critical since
it fixes a problem where multiplatform kernels panic on all but prima2
hardware.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=c555
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"These are a little later than I planned on since I got caught up with
handling merges for 3.11 most of the week.
Another week, another batch of fixes for arm-soc platforms.
Again, nothing controversial. A few more than would be ideal, but all
are valid fixes. In particular the prima2 panic patch is critical
since it fixes a problem where multiplatform kernels panic on all but
prima2 hardware."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: SAMSUNG: pm: Adjust for pinctrl- and DT-enabled platforms
ARM: prima2: fix incorrect panic usage
arm: mvebu: armada-xp-{gp,openblocks-ax3-4}: specify PCIe range
ARM: Kirkwood: handle mv88f6282 cpu in __kirkwood_variant().
ARM: omap3: clock: fix wrong container_of in clock36xx.c
ARM: dts: OMAP5: Fix missing PWM capability to timer nodes
ARM: dts: omap4-panda|sdp: Fix mux for twl6030 IRQ pin and msecure line
ARM: dts: AM33xx: Fix properties on gpmc node
arm: omap2: fix AM33xx hwmod infos for UART2
ARM: OMAP3: Fix iva2_pwrdm settings for 3703
Pull networking fixes from David Miller:
1) Fix RTNL locking in batman-adv, from Matthias Schiffer.
2) Don't allow non-passthrough macvlan devices to set NOPROMISC via
netlink, otherwise we can end up with corrupted promisc counter
values on the device. From Michael S Tsirkin.
3) Fix stmmac driver build with debugging defines enabled, from Dinh
Nguyen.
4) Make sure name string we give in socket address in AF_PACKET is NULL
terminated, from Daniel Borkmann.
5) Fix leaking of two uninitialized bytes of memory to userspace in
l2tp, from Guillaume Nault.
6) Clear IPCB(skb) before tunneling otherwise we touch dangling IP
options state and crash. From Saurabh Mohan.
7) Fix suspend/resume for davinci_mdio by using suspend_late and
resume_early. From Mugunthan V N.
8) Don't tag ip_tunnel_init_net and ip_tunnel_delete_net with
__net_{init,exit}, they can be called outside of those contexts.
From Eric Dumazet.
9) Fix RX length error in sh_eth driver, from Yoshihiro Shimoda.
10) Fix missing sctp_outq initialization in some code paths of SCTP
stack, from Neil Horman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
sctp: fully initialize sctp_outq in sctp_outq_init
netiucv: Hold rtnl between name allocation and device registration.
tulip: Properly check dma mapping result
net: sh_eth: fix incorrect RX length error if R8A7740
ip_tunnel: remove __net_init/exit from exported functions
drivers: net: davinci_mdio: restore mdio clk divider in mdio resume
drivers: net: davinci_mdio: moving mdio resume earlier than cpsw ethernet driver
net/ipv4: ip_vti clear skb cb before tunneling.
tg3: Wait for boot code to finish after power on
l2tp: Fix sendmsg() return value
l2tp: Fix PPP header erasure and memory leak
bonding: fix igmp_retrans type and two related races
bonding: reset master mac on first enslave failure
packet: packet_getname_spkt: make sure string is always 0-terminated
net: ethernet: stmicro: stmmac: Fix compile error when STMMAC_XMIT_DEBUG used
be2net: Fix 32-bit DMA Mask handling
xen-netback: don't de-reference vif pointer after having called xenvif_put()
macvlan: don't touch promisc without passthrough
batman-adv: Don't handle address updates when bla is disabled
batman-adv: forward late OGMs from best next hop
...
Pull powerpc fixes from Benjamin Herrenschmidt:
"So here are 3 fixes still for 3.10. Fixes are simple, bugs are nasty
(though not recent regressions, nasty enough) and all targeted at
stable"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix missing/delayed calls to irq_work
powerpc: Fix emulation of illegal instructions on PowerNV platform
powerpc: Fix stack overflow crash in resume_kernel when ftracing
Thanks to commit f91eb62f71 ("init: scream bloody murder if interrupts
are enabled too early"), "bloody murder" is now being screamed.
With a MIPS OCTEON config, we use on_each_cpu() in our
irq_chip.irq_bus_sync_unlock() function. This gets called in early as a
result of the time_init() call. Because the !SMP version of
on_each_cpu() unconditionally enables irqs, we get:
WARNING: at init/main.c:560 start_kernel+0x250/0x410()
Interrupts were enabled early
CPU: 0 PID: 0 Comm: swapper Not tainted 3.10.0-rc5-Cavium-Octeon+ #801
Call Trace:
show_stack+0x68/0x80
warn_slowpath_common+0x78/0xb0
warn_slowpath_fmt+0x38/0x48
start_kernel+0x250/0x410
Suggested fix: Do what we already do in the SMP version of
on_each_cpu(), and use local_irq_save/local_irq_restore. Because we
need a flags variable, make it a static inline to avoid name space
issues.
[ Change from v1: Convert on_each_cpu to a static inline function, add
#include <linux/irqflags.h> to avoid build breakage on some files.
on_each_cpu_mask() and on_each_cpu_cond() suffer the same problem as
on_each_cpu(), but they are not causing !SMP bugs for me, so I will
defer changing them to a less urgent patch. ]
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull VFS fixes from Al Viro:
"Several fixes + obvious cleanup (you've missed a couple of open-coded
can_lookup() back then)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
snd_pcm_link(): fix a leak...
use can_lookup() instead of direct checks of ->i_op->lookup
move exit_task_namespaces() outside of exit_notify()
fput: task_work_add() can fail if the caller has passed exit_task_work()
ncpfs: fix rmdir returns Device or resource busy
- Remove noisy warnings about experimental support which spams the logs
- Add padding to align directory and attr structures correctly
- Set block number on child buffer on a root btree split
- Disable verifiers during log recovery for non-CRC filesystems
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=bijX
-----END PGP SIGNATURE-----
Merge tag 'for-linus-v3.10-rc6' of git://oss.sgi.com/xfs/xfs
Pull xfs fixes from Ben Myers:
- Remove noisy warnings about experimental support which spams the logs
- Add padding to align directory and attr structures correctly
- Set block number on child buffer on a root btree split
- Disable verifiers during log recovery for non-CRC filesystems
* tag 'for-linus-v3.10-rc6' of git://oss.sgi.com/xfs/xfs:
xfs: don't shutdown log recovery on validation errors
xfs: ensure btree root split sets blkno correctly
xfs: fix implicit padding in directory and attr CRC formats
xfs: don't emit v5 superblock warnings on write
Here are some small mei driver fixes for 3.10-rc6 that fix some reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlG7RgwACgkQMUfUDdst+ynQjgCcCed/djDG6rEk8OHNwtH0qsGE
3o4AnjEW26lnses9dpudJOzhFGggCKJt
=wN5b
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc fixes from Greg Kroah-Hartman:
"Here are some small mei driver fixes for 3.10-rc6 that fix some
reported problems"
* tag 'char-misc-3.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mei: me: clear interrupts on the resume path
mei: nfc: fix nfc device freeing
mei: init: Flush scheduled work before resetting the device
Here are some small USB driver fixes that resolve some reported problems
for 3.10-rc6
Nothing major, just 3 USB serial driver fixes, and two chipidea fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlG7Rq0ACgkQMUfUDdst+ykKmwCg0mta+HehUtBYrhLJGq9uADix
0YMAn1hEPP26BhVl/7a6GL+s8UoSVFxo
=9Vkq
-----END PGP SIGNATURE-----
Merge tag 'usb-3.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are some small USB driver fixes that resolve some reported
problems for 3.10-rc6
Nothing major, just 3 USB serial driver fixes, and two chipidea fixes"
* tag 'usb-3.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: chipidea: fix id change handling
usb: chipidea: fix no transceiver case
USB: pl2303: fix device initialisation at open
USB: spcp8x5: fix device initialisation at open
USB: f81232: fix device initialisation at open
When replaying interrupts (as a result of the interrupt occurring
while soft-disabled), in the case of the decrementer, we are exclusively
testing for a pending timer target. However we also use decrementer
interrupts to trigger the new "irq_work", which in this case would
be missed.
This change the logic to force a replay in both cases of a timer
boundary reached and a decrementer interrupt having actually occurred
while disabled. The former test is still useful to catch cases where
a CPU having been hard-disabled for a long time completely misses the
interrupt due to a decrementer rollover.
CC: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Normally, the kernel emulates a few instructions that are unimplemented
on some processors (e.g. the old dcba instruction), or privileged (e.g.
mfpvr). The emulation of unimplemented instructions is currently not
working on the PowerNV platform. The reason is that on these machines,
unimplemented and illegal instructions cause a hypervisor emulation
assist interrupt, rather than a program interrupt as on older CPUs.
Our vector for the emulation assist interrupt just calls
program_check_exception() directly, without setting the bit in SRR1
that indicates an illegal instruction interrupt. This fixes it by
making the emulation assist interrupt set that bit before calling
program_check_interrupt(). With this, old programs that use no-longer
implemented instructions such as dcba now work again.
CC: <stable@vger.kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It's possible for us to crash when running with ftrace enabled, eg:
Bad kernel stack pointer bffffd12 at c00000000000a454
cpu 0x3: Vector: 300 (Data Access) at [c00000000ffe3d40]
pc: c00000000000a454: resume_kernel+0x34/0x60
lr: c00000000000335c: performance_monitor_common+0x15c/0x180
sp: bffffd12
msr: 8000000000001032
dar: bffffd12
dsisr: 42000000
If we look at current's stack (paca->__current->stack) we see it is
equal to c0000002ecab0000. Our stack is 16K, and comparing to
paca->kstack (c0000002ecab3e30) we can see that we have overflowed our
kernel stack. This leads to us writing over our struct thread_info, and
in this case we have corrupted thread_info->flags and set
_TIF_EMULATE_STACK_STORE.
Dumping the stack we see:
3:mon> t c0000002ecab0000
[c0000002ecab0000] c00000000002131c .performance_monitor_exception+0x5c/0x70
[c0000002ecab0080] c00000000000335c performance_monitor_common+0x15c/0x180
--- Exception: f01 (Performance Monitor) at c0000000000fb2ec .trace_hardirqs_off+0x1c/0x30
[c0000002ecab0370] c00000000016fdb0 .trace_graph_entry+0xb0/0x280 (unreliable)
[c0000002ecab0410] c00000000003d038 .prepare_ftrace_return+0x98/0x130
[c0000002ecab04b0] c00000000000a920 .ftrace_graph_caller+0x14/0x28
[c0000002ecab0520] c0000000000d6b58 .idle_cpu+0x18/0x90
[c0000002ecab05a0] c00000000000a934 .return_to_handler+0x0/0x34
[c0000002ecab0620] c00000000001e660 .timer_interrupt+0x160/0x300
[c0000002ecab06d0] c0000000000025dc decrementer_common+0x15c/0x180
--- Exception: 901 (Decrementer) at c0000000000104d4 .arch_local_irq_restore+0x74/0xa0
[c0000002ecab09c0] c0000000000fe044 .trace_hardirqs_on+0x14/0x30 (unreliable)
[c0000002ecab0fb0] c00000000016fe3c .trace_graph_entry+0x13c/0x280
[c0000002ecab1050] c00000000003d038 .prepare_ftrace_return+0x98/0x130
[c0000002ecab10f0] c00000000000a920 .ftrace_graph_caller+0x14/0x28
[c0000002ecab1160] c0000000000161f0 .__ppc64_runlatch_on+0x10/0x40
[c0000002ecab11d0] c00000000000a934 .return_to_handler+0x0/0x34
--- Exception: 901 (Decrementer) at c0000000000104d4 .arch_local_irq_restore+0x74/0xa0
... and so on
__ppc64_runlatch_on() is called from RUNLATCH_ON in the exception entry
path. At that point the irq state is not consistent, ie. interrupts are
hard disabled (by the exception entry), but the paca soft-enabled flag
may be out of sync.
This leads to the local_irq_restore() in trace_graph_entry() actually
enabling interrupts, which we do not want. Because we have not yet
reprogrammed the decrementer we immediately take another decrementer
exception, and recurse.
The fix is twofold. Firstly make sure we call DISABLE_INTS before
calling RUNLATCH_ON. The badly named DISABLE_INTS actually reconciles
the irq state in the paca with the hardware, making it safe again to
call local_irq_save/restore().
Although that should be sufficient to fix the bug, we also mark the
runlatch routines as notrace. They are called very early in the
exception entry and we are asking for trouble tracing them. They are
also fairly uninteresting and tracing them just adds unnecessary
overhead.
[ This regression was introduced by fe1952fc0a
"powerpc: Rework runlatch code" by myself --BenH
]
CC: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
exit_notify() does exit_task_namespaces() after
forget_original_parent(). This was needed to ensure that ->nsproxy
can't be cleared prematurely, an exiting child we are going to
reparent can do do_notify_parent() and use the parent's (ours) pid_ns.
However, after 32084504 "pidns: use task_active_pid_ns in
do_notify_parent" ->nsproxy != NULL is no longer needed, we rely
on task_active_pid_ns().
Move exit_task_namespaces() from exit_notify() to do_exit(), after
exit_fs() and before exit_task_work().
This solves the problem reported by Andrey, free_ipc_ns()->shm_destroy()
does fput() which needs task_work_add().
Note: this particular problem can be fixed if we change fput(), and
that change makes sense anyway. But there is another reason to move
the callsite. The original reason for exit_task_namespaces() from
the middle of exit_notify() was subtle and it has already gone away,
now this looks confusing. And this allows us do simplify exit_notify(),
we can avoid unlock/lock(tasklist) and we can use ->exit_state instead
of PF_EXITING in forget_original_parent().
Reported-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
fput() assumes that it can't be called after exit_task_work() but
this is not true, for example free_ipc_ns()->shm_destroy() can do
this. In this case fput() silently leaks the file.
Change it to fallback to delayed_fput_work if task_work_add() fails.
The patch looks complicated but it is not, it changes the code from
if (PF_KTHREAD) {
schedule_work(...);
return;
}
task_work_add(...)
to
if (!PF_KTHREAD) {
if (!task_work_add(...))
return;
/* fallback */
}
schedule_work(...);
As for shm_destroy() in particular, we could make another fix but I
think this change makes sense anyway. There could be another similar
user, it is not safe to assume that task_work_add() can't fail.
Reported-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Unfortunately, we cannot guarantee that items logged multiple times
and replayed by log recovery do not take objects back in time. When
they are taken back in time, the go into an intermediate state which
is corrupt, and hence verification that occurs on this intermediate
state causes log recovery to abort with a corruption shutdown.
Instead of causing a shutdown and unmountable filesystem, don't
verify post-recovery items before they are written to disk. This is
less than optimal, but there is no way to detect this issue for
non-CRC filesystems If log recovery successfully completes, this
will be undone and the object will be consistent by subsequent
transactions that are replayed, so in most cases we don't need to
take drastic action.
For CRC enabled filesystems, leave the verifiers in place - we need
to call them to recalculate the CRCs on the objects anyway. This
recovery problem can be solved for such filesystems - we have a LSN
stamped in all metadata at writeback time that we can to determine
whether the item should be replayed or not. This is a separate piece
of work, so is not addressed by this patch.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 9222a9cf86)
For CRC enabled filesystems, the BMBT is rooted in an inode, so it
passes through a different code path on root splits than the
freespace and inode btrees. This is much less traversed by xfstests
than the other trees. When testing on a 1k block size filesystem,
I've been seeing ASSERT failures in generic/234 like:
XFS: Assertion failed: cur->bc_btnum != XFS_BTNUM_BMAP || cur->bc_private.b.allocated == 0, file: fs/xfs/xfs_btree.c, line: 317
which are generally preceded by a lblock check failure. I noticed
this in the bmbt stats:
$ pminfo -f xfs.btree.block_map
xfs.btree.block_map.lookup
value 39135
xfs.btree.block_map.compare
value 268432
xfs.btree.block_map.insrec
value 15786
xfs.btree.block_map.delrec
value 13884
xfs.btree.block_map.newroot
value 2
xfs.btree.block_map.killroot
value 0
.....
Very little coverage of root splits and merges. Indeed, on a 4k
filesystem, block_map.newroot and block_map.killroot are both zero.
i.e. the code is not exercised at all, and it's the only generic
btree infrastructure operation that is not exercised by a default run
of xfstests.
Turns out that on a 1k filesystem, generic/234 accounts for one of
those two root splits, and that is somewhat of a smoking gun. In
fact, it's the same problem we saw in the directory/attr code where
headers are memcpy()d from one block to another without updating the
self describing metadata.
Simple fix - when copying the header out of the root block, make
sure the block number is updated correctly.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit ade1335afe)
Michael L. Semon has been testing CRC patches on a 32 bit system and
been seeing assert failures in the directory code from xfs/080.
Thanks to Michael's heroic efforts with printk debugging, we found
that the problem was that the last free space being left in the
directory structure was too small to fit a unused tag structure and
it was being corrupted and attempting to log a region out of bounds.
Hence the assert failure looked something like:
.....
#5 calling xfs_dir2_data_log_unused() 36 32
#1 4092 4095 4096
#2 8182 8183 4096
XFS: Assertion failed: first <= last && last < BBTOB(bp->b_length), file: fs/xfs/xfs_trans_buf.c, line: 568
Where #1 showed the first region of the dup being logged (i.e. the
last 4 bytes of a directory buffer) and #2 shows the corrupt values
being calculated from the length of the dup entry which overflowed
the size of the buffer.
It turns out that the problem was not in the logging code, nor in
the freespace handling code. It is an initial condition bug that
only shows up on 32 bit systems. When a new buffer is initialised,
where's the freespace that is set up:
[ 172.316249] calling xfs_dir2_leaf_addname() from xfs_dir_createname()
[ 172.316346] #9 calling xfs_dir2_data_log_unused()
[ 172.316351] #1 calling xfs_trans_log_buf() 60 63 4096
[ 172.316353] #2 calling xfs_trans_log_buf() 4094 4095 4096
Note the offset of the first region being logged? It's 60 bytes into
the buffer. Once I saw that, I pretty much knew that the bug was
going to be caused by this.
Essentially, all direct entries are rounded to 8 bytes in length,
and all entries start with an 8 byte alignment. This means that we
can decode inplace as variables are naturally aligned. With the
directory data supposedly starting on a 8 byte boundary, and all
entries padded to 8 bytes, the minimum freespace in a directory
block is supposed to be 8 bytes, which is large enough to fit a
unused data entry structure (6 bytes in size). The fact we only have
4 bytes of free space indicates a directory data block alignment
problem.
And what do you know - there's an implicit hole in the directory
data block header for the CRC format, which means the header is 60
byte on 32 bit intel systems and 64 bytes on 64 bit systems. Needs
padding. And while looking at the structures, I found the same
problem in the attr leaf header. Fix them both.
Note that this only affects 32 bit systems with CRCs enabled.
Everything else is just fine. Note that CRC enabled filesystems created
before this fix on such systems will not be readable with this fix
applied.
Reported-by: Michael L. Semon <mlsemon35@gmail.com>
Debugged-by: Michael L. Semon <mlsemon35@gmail.com>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Ben Myers <bpm@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 8a1fd2950e)
We write the superblock every 30s or so which results in the
verifier being called. Right now that results in this output
every 30s:
XFS (vda): Version 5 superblock detected. This kernel has EXPERIMENTAL support enabled!
Use of these features in this kernel is at your own risk!
And spamming the logs.
We don't need to check for whether we support v5 superblocks or
whether there are feature bits we don't support set as these are
only relevant when we first mount the filesytem. i.e. on superblock
read. Hence for the write verification we can just skip all the
checks (and hence verbose output) altogether.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 34510185ab)
Pull btrfs fixes from Chris Mason:
"This is an assortment of crash fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: stop all workers before cleaning up roots
Btrfs: fix use-after-free bug during umount
Btrfs: init relocate extent_io_tree with a mapping
btrfs: Drop inode if inode root is NULL
Btrfs: don't delete fs_roots until after we cleanup the transaction
We need to clear pending interrupts on the resume
path. This brings the device into defined state
before starting the reset flow
This should solve suspend/resume issues:
mei_me : wait hw ready failed. status = 0x0
mei_me : version message write failed
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Flushing pending work items before resetting the device makes more
sense than doing so afterwards. Some of them, like e.g. the NFC
initialization one, find themselves with client IDs changed after
the reset, eventually leading to trigger a client.c:mei_me_cl_by_id()
warning after a few modprobe/rmmod cycles.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 2f94aabd9f
(refactor sctp_outq_teardown to insure proper re-initalization)
we modified sctp_outq_teardown to use sctp_outq_init to fully re-initalize the
outq structure. Steve West recently asked me why I removed the q->error = 0
initalization from sctp_outq_teardown. I did so because I was operating under
the impression that sctp_outq_init would properly initalize that value for us,
but it doesn't. sctp_outq_init operates under the assumption that the outq
struct is all 0's (as it is when called from sctp_association_init), but using
it in __sctp_outq_teardown violates that assumption. We should do a memset in
sctp_outq_init to ensure that the entire structure is in a known state there
instead.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: "West, Steve (NSN - US/Fort Worth)" <steve.west@nsn.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: netdev@vger.kernel.org
CC: davem@davemloft.net
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fixes a race condition between concurrent initializations of netiucv devices
that try to use the same name.
sysfs: cannot create duplicate filename '/devices/iucv/netiucv2'
[...]
Call Trace:
([<00000000002edea4>] sysfs_add_one+0xb0/0xdc)
[<00000000002eecd4>] create_dir+0x80/0xfc
[<00000000002eee38>] sysfs_create_dir+0xe8/0x118
[<00000000003835a8>] kobject_add_internal+0x120/0x2d0
[<00000000003839d6>] kobject_add+0x62/0x9c
[<00000000003d9564>] device_add+0xcc/0x510
[<000003e00212c7b4>] netiucv_register_device+0xc0/0x1ec [netiucv]
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Tested-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tulip throws an error when dma debugging is enabled, as it doesn't properly
check dma mapping results with dma_mapping_error() durring tx ring refills.
Easy fix, just add it in, and drop the frame if the mapping is bad
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Grant Grundler <grundler@parisc-linux.org>
CC: "David S. Miller" <davem@davemloft.net>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This branch contains the following bug fixes:
- Fix locking vs. interrupts. Bug caught by lockdep checks
- Fix parsing of cpp #line directive output by dtc
- Fix 'make clean' for dtc temporary files.
There is also a commit that regenerates the dtc lexer and parser files
with Bison 2.5. The only purpose of this commit is to separate the
functional change in the dtc bug fix from the code generation change
caused by a different Bison version.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=om+W
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree bug fixes from Grant Likely:
"This branch contains the following bug fixes:
- Fix locking vs. interrupts. Bug caught by lockdep checks
- Fix parsing of cpp #line directive output by dtc
- Fix 'make clean' for dtc temporary files.
There is also a commit that regenerates the dtc lexer and parser files
with Bison 2.5. The only purpose of this commit is to separate the
functional change in the dtc bug fix from the code generation change
caused by a different Bison version"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
dtc: ensure #line directives don't consume data from the next line
dtc: Update generated files to output from Bison 2.5
of: Fix locking vs. interrupts
kbuild: make sure we clean up DTB temporary files
Previously, the #line parsing regex ended with ({WS}+[0-9]+)?. The {WS}
could match line-break characters. If the #line directive did not contain
the optional flags field at the end, this could cause any integer data on
the next line to be consumed as part of the #line directive parsing. This
could cause syntax errors (i.e. #line parsing consuming the leading 0
from a hex literal 0x1234, leaving x1234 to be parsed as cell data,
which is a syntax error), or invalid compilation results (i.e. simply
consuming literal 1234 as part of the #line processing, thus removing it
from the cell data).
Fix this by replacing {WS} with [ \t] so that it can't match line-breaks.
Convert all instances of {WS}, even though the other instances should be
irrelevant for any well-formed #line directive. This is done for
consistency and ultimate safety.
[Cherry picked from DTC commit a1ee6f068e1c8dbc62873645037a353d7852d5cc]
Reported-by: Ian Campbell <Ian.Campbell@citrix.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch merely updates the generated dtc parser and lexer files to
the output generated by Bison 2.5. The previous versions were generated
from version 2.4.1. The only reason for this commit is to minimize the
diff on the next commit which fixes a bug in the DTC #line directive
parsing. Otherwise the Bison changes would be intermingled with the
functional changes.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The OF code uses irqsafe locks everywhere except in a handful of functions
for no obvious reasons. Since the conversion from the old rwlocks, this
now triggers lockdep warnings when used at interrupt time. At least one
driver (ibmvscsi) seems to be doing that from softirq context.
This converts the few non-irqsafe locks into irqsafe ones, making them
consistent with the rest of the code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Various temporary files used when building DTB files were not suffixed with
.tmp and therefore were not cleaned up by "make clean".
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
- ACPI fix for an issue causing ACPI video driver to attempt to bind
to devices it shouldn't touch from Rafael J Wysocki.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=1N+6
-----END PGP SIGNATURE-----
Merge tag 'acpi-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"This is an alternative fix for the regression introduced in 3.9 whose
previous fix had to be reverted right before 3.10-rc5, because it
broke one of the Tony's machines.
In this one the check is confined to the ACPI video driver (which is
the only one causing the problem to happen in the first place) and the
Tony's box shouldn't even notice it.
- ACPI fix for an issue causing ACPI video driver to attempt to bind
to devices it shouldn't touch from Rafael J Wysocki."
* tag 'acpi-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: Do not bind to device objects with a scan handler
Pull x86 fixes from Peter Anvin:
"Another set of fixes, the biggest bit of this is yet another tweak to
the UEFI anti-bricking code; apparently we finally got some feedback
from Samsung as to what makes at least their systems fail. This set
should actually fix the boot regressions that some other systems (e.g.
SGI) have exhibited.
Other than that, there is a patch to avoid a panic with particularly
unhappy memory layouts and two minor protocol fixes which may or may
not be manifest bugs"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Fix typo in kexec register clearing
x86, relocs: Move __vvar_page from S_ABS to S_REL
Modify UEFI anti-bricking code
x86: Fix adjust_range_size_mask calling position
Pull RCU fixes from Paul McKenney:
"I must confess that this past merge window was not RCU's best showing.
This series contains three more fixes for RCU regressions:
1. A fix to __DECLARE_TRACE_RCU() that causes it to act as an
interrupt from idle rather than as a task switch from idle.
This change is needed due to the recent use of _rcuidle()
tracepoints that can be invoked from interrupt handlers as well
as from idle. Without this fix, invoking _rcuidle() tracepoints
from interrupt handlers results in splats and (more seriously)
confusion on RCU's part as to whether a given CPU is idle or not.
This confusion can in turn result in too-short grace periods and
therefore random memory corruption.
2. A fix to a subtle deadlock that could result due to RCU doing
a wakeup while holding one of its rcu_node structure's locks.
Although the probability of occurrence is low, it really
does happen. The fix, courtesy of Steven Rostedt, uses
irq_work_queue() to avoid the deadlock.
3. A fix to a silent deadlock (invisible to lockdep) due to the
interaction of timeouts posted by RCU debug code enabled by
CONFIG_PROVE_RCU_DELAY=y, grace-period initialization, and CPU
hotplug operations. This will not occur in production kernels,
but really does occur in randconfig testing. Diagnosis courtesy
of Steven Rostedt"
* 'rcu/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
rcu: Fix deadlock with CPU hotplug, RCU GP init, and timer migration
rcu: Don't call wakeup() with rcu_node structure ->lock held
trace: Allow idle-safe tracepoints to be called from irq
Pull s390 fixes from Martin Schwidefsky:
"Three kvm related memory management fixes, a fix for show_trace, a fix
for early console output and a patch from Ben to help prevent compile
errors in regard to irq functions (or our lack thereof)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: Implement IRQ functions if !PCI
s390/sclp: fix new line detection
s390/pgtable: make pgste lock an explicit barrier
s390/pgtable: Save pgste during modify_prot_start/commit
s390/dumpstack: fix address ranges for asynchronous and panic stack
s390/pgtable: Fix guest overindication for change bit
As well as the usual driver specifics we've got a couple of core fixes
here, one fixing capabilities for unidirectional streams and the other
fixing suspend while audio streams are active. The suspend fix is a
little involved but mostly as a result of removing some special casing
that was doing the wrong thing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=pK3d
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound
Pull ASoC sound updates from Mark Brown:
"Takashi is travelling at the minute and it'd be good to get the
MAINTAINERS update in here merged so sending directly.
As well as the usual driver specifics we've got a couple of core fixes
here, one fixing capabilities for unidirectional streams and the other
fixing suspend while audio streams are active.
The suspend fix is a little involved but mostly as a result of
removing some special casing that was doing the wrong thing."
* tag 'asoc-v3.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound:
ASoC: tlv320aic3x: Remove deadlock from snd_soc_dapm_put_volsw_aic3x()
ASoC: dapm: Treat DAI widgets like AIF widgets for power
ASoC: arizona: Correct AEC loopback enable
ASoC: pcm: Require both CODEC and CPU support when declaring stream caps
MAINTAINERS: Remove myself from Wolfson maintainers
ASoC: wm8994: Ensure microphone detection state is reset on removal
ASoC: wm8994: Avoid leaking pm_runtime reference on removed jack race
ASoC: cs42l52: fix hp_gain_enum shift value.
ASoC: cs42l52: use correct PCM mixer TLV dB scale to match datasheet.
Some tagged for -stable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=8iy3
-----END PGP SIGNATURE-----
Merge tag 'md-3.10-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"A few bugfixes for md
Some tagged for -stable"
* tag 'md-3.10-fixes' of git://neil.brown.name/md:
md/raid1,5,10: Disable WRITE SAME until a recovery strategy is in place
md/raid1,raid10: use freeze_array in place of raise_barrier in various places.
md/raid1: consider WRITE as successful only if at least one non-Faulty and non-rebuilding drive completed it.
md: md_stop_writes() should always freeze recovery.
On platforms with C8-C10 support, the additional C-states cause
turbostat to overrun its output buffer of 128 bytes per CPU. Increase
this to 256 bytes per CPU.
[ As a bugfix, this should go into 3.10; however, since the C8-C10
support didn't go in until after 3.9, this need not go into any stable
kernel. ]
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
few users were reporting boot regressions in v3.9. This has now been
fixed with a more accurate "minimum storage requirement to avoid
bricking" value from Samsung (5K instead of 50%) and code to trigger
garbage collection when we near our limit - Matthew Garrett.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=TZuM
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent' into x86/urgent
* More tweaking to the EFI variable anti-bricking algorithm. Quite a
few users were reporting boot regressions in v3.9. This has now been
fixed with a more accurate "minimum storage requirement to avoid
bricking" value from Samsung (5K instead of 50%) and code to trigger
garbage collection when we near our limit - Matthew Garrett.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This patch fixes an issue that the driver increments the "RX length error"
on every buffer in sh_eth_rx() if the R8A7740.
This patch also adds a description about the Receive Frame Status bits.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_NET_NS is not set then __net_init is the same as __init and
__net_exit is the same as __exit. These functions will be removed from
memory after the module loads or is removed. Functions that are exported
for use by other functions should never be labeled for removal.
Bug introduced by commit c544193214
("GRE: Refactor GRE tunneling code.")
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During suspend resume cycle all the register data is lost, so MDIO
clock divier value gets reset. This patch restores the clock divider
value.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO driver should resume before CPSW ethernet driver so that CPSW connect
to the phy and start tx/rx ethernet packets, changing the suspend/resume
apis with suspend_late/resume_early.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If users apply shaper to vti tunnel then it will cause a kernel crash. The
problem seems to be due to the vti_tunnel_xmit function not clearing
skb->opt field before passing the packet to xfrm tunneling code.
Signed-off-by: Saurabh Mohan <saurabh@vyatta.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Henningsson