If the basic rate set is configured to not include the lowest rate
(e.g., basic rate set = 6, 12, 24 Mbps in IEEE 802.11g mode), the AP
should not send out broadcast frames at 1 Mbps. This type of
configuration can be used to optimize channel usage in cases where
there is no need for backwards compatibility with IEEE 802.11b-only
devices.
In AP mode, mac80211 was unconditionally using the lowest rate for
Beacon frames and similarly, with all rate control algorithms that use
rate_control_send_low(), the lowest rate ended up being used for all
broadcast frames (and all unicast frames that are sent before
association). Change this to take into account the basic rate
configuration in AP mode, i.e., use the lowest rate in the basic rate
set instead of the lowest supported rate when selecting the rate.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make addba_resp_timer aware the HT_AGG_STATE_REQ_STOP_BA_MSK mask
so that when ___ieee80211_stop_tx_ba_session() is issued the timer
will quit. Otherwise when suspend happens before the timer expired,
the timer handler will be called immediately after resume and
messes up driver status.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The callback sets slot time as specified in IEEE 802.11-2007 section
17.3.8.6 (for 20MHz channels only for now) and raises ACK and CTS
timeouts accordingly. The values are persistent, they are restored after
device reset.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original code was correct in 802.11a mode only, 802.11b/g uses
different clock rates. The new code uses values taken from FreeBSD HAL
and should be correct for all modes including turbo modes.
The former rate calculation was used by slope coefficient calculation
function ath5k_hw_write_ofdm_timings. However, this function requires
the 802.11a values even in 802.11g mode. Thus the use of
ath5k_hw_htoclock was replaced by hardcoded values. Possibly the slope
coefficient calculation is not related to clock rate at all.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Functions ath5k_hw_get_slot_time and ath5k_hw_set_slot_time were
converting microseconds to clocks only for AR5210, although it's needed
for all supported devices. The conversion was moved outside the
hardware-specific branches.
The original code also limited minimum slot time to 9, while turbo modes
use 6, this was fixed too.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mac80211 callback to driver set_coverage_class() sets slot time and ACK
timeout for given IEEE 802.11 coverage class. The callback is optional,
but it's essential for long distance links.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new attribute NL80211_ATTR_WIPHY_COVERAGE_CLASS sets IEEE 802.11
Coverage Class, which depends on maximum distance of nodes in a
wireless network. It's required for long distance links (more than a few
hundred meters).
The attribute is now ignored by two non-mac80211 drivers, rndis and
iwmc3200wifi, together with WIPHY_PARAM_RETRY_SHORT and
WIPHY_PARAM_RETRY_LONG. If it turns out to be a problem, we could split
set_wiphy_params callback or add new capability bits.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The newer single chip hardware family of chipsets have not been
experiencing issues with power saving set by default with recent
fixes merged (even into stable). The remaining issues are only
reported with AR5416 and since enabling PS by default can increase
power savings considerably best to take advantage of that feature
as this has been tested properly.
For more details on this issue see the bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=14267
We leave AR5416 with PS disabled by default, that seems to require
some more work.
Cc: stable@kernel.org
Cc: Peter Stuge <peter@stuge.se>
Cc: Justin P. Mattock <justinmattock@gmail.com>
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 53623f1a09.
This was inadvertantly missed in "mac80211: fix skb buffering issue",
and is required with that patch to restore proper queue operation.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: fix skb buffering issue" is based on what will become 2.6.34,
so it includes an incompatible usage of sta_info_get. This patch will
need to be effectively reverted when merging for 2.6.34.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The start_seq_num is taken from the station's tid_seq[tid].
This is fine, except tid_seq sequence counter is shifted
by 4 bits to accommodate for frame fragmentation.
Both (iwlagn & ath9k) were unaffected by this minor glitch,
because they don't read the *ssn for the AMPDU_TX_START action.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables HT association and AMPDU in the receive direction for
STA firmware images on hardware that supports it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AMPDU receive doesn't need any special handling, so let's enable
this before tackling the transmit side.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass the AP's MCS rate mask to SET_RATE when associating, and make
UPDATE_STADB pass in the peer's HT caps and rates when adding a new
hardware station database entry.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, mwl8k_bss_info_changed() would refuse to do anything if
the 'changed' argument indicated that the association status hadn't
changed. Fix this up so that it will allow changing things like the
preamble type, the slot time and the CTS-to-self protection method
without having to reassociate.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When calling SET_RATE, SET_AID, or when creating a station database
entry for our AP, pass in the AP's rate set instead of just blindly
enabling all legacy rates, so as to end up doing the right thing when
talking to 11b-only APs.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For STA firmware, move the per-peer hardware station ID to the
driver-private part of struct ieee80211_sta, where it belongs.
(Since issuing a hardware station database maintenance command sleeps,
we can't hold a reference to the ieee80211_sta * across the command,
and since we won't know the station ID until after the command
completes, we need to re-lookup the sta when the command is done to
write the returned station ID back to its driver-private part.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inserting and removing a hardware station database entry for the AP
when we are in managed mode is currently done in ->bss_info_changed().
To prepare for adding AP mode support, implement the ->sta_notify()
driver method, and let that handle inserting and removing the hardware
station database entry for our AP instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of sprinkling code with ifdef's define REG_DBG_PRINT() instead.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting the mac address from user space was buggy. For example, when
executing this command:
ip link set wlan0 address 00:1f:df:88:cd:55
mac80211 used the address 01:00:00:1f:df:88 instead. It was shifted two
bytes.
The reason was that the addr (type of void *) provided to
ieee80211_change_mac() is actually of type struct sockaddr, not just the
mac address array. Also the call to eth_mac_addr() expects the address to
be struct sockaddr.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On a 32 bit system (in this case an omap 3430 system) gcc warned about
pointer conversion:
net/mac80211/work.c: In function 'ieee80211_remain_on_channel_timeout':
net/mac80211/work.c:534: warning: cast from pointer to integer of different size
net/mac80211/work.c: In function 'ieee80211_remain_done':
net/mac80211/work.c:1030: warning: cast from pointer to integer of different size
net/mac80211/work.c: In function 'ieee80211_wk_remain_on_channel':
net/mac80211/work.c:1056: warning: cast from pointer to integer of different size
net/mac80211/work.c: In function 'ieee80211_wk_cancel_remain_on_channel':
net/mac80211/work.c:1072: warning: cast from pointer to integer of different size
Fix it by casting the pointers to unsigned long instead. This makes the
compiler happy again.
Compile-tested only.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the forgotten linux/wireless.h inclusion from mac80211.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 250cce26d5 uses UTS_RELEASE
as the the in-tree iwlwifi driver version. However the inclusion
of generated/utsrelease.h makes it a unpleasant behaviour to
recompile the driver everytime when utsrelease.h is updated. In
fact, the driver module is already built with the UTS_RELEASE
information via vermagic of modinfo. Mark the in-tree driver
with the version string "in-tree" to distinguish with those old
out-of-tree drivers.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current rt2x00 drivers may result in a "ieee80211_tx_status: headroom too
small" error message when a frame needs to be properly aligned before
transmitting it.
This is because the space needed to ensure proper alignment isn't
requested from mac80211.
Fix this by adding sufficient amount of alignment space to the amount
of headroom requested for TX frames.
Reported-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since I removed the master netdev, we've been
keeping internal queues only, and even before
that we never told the networking stack above
the virtual interfaces about congestion. This
means that packets are queued in mac80211 and
the upper layers never know, possibly leading
to memory exhaustion and other problems.
This patch makes all interfaces multiqueue and
uses ndo_select_queue to put the packets into
queues per AC. Additionally, when the driver
stops a queue, we now stop all corresponding
queues for the virtual interfaces as well.
The injection case will use VO by default for
non-data frames, and BE for data frames, but
downgrade any data frames according to ACM. It
needs to be fleshed out in the future to allow
chosing the queue/AC in radiotap.
Reported-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.32]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800_blink_set uses an illegal value to set the LED_CFG_G_LED_MODE
field of the LED_CFG register. This field is only 2 bits large, so
should be initialized with value that fits. Use default value from
the vendor driver.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use rt2x00dev->ops->extra_tx_headroom, not rt2x00dev->hw->extra_tx_headroom
in the tx code, as the later may include other headroom not to be used in
the chipset driver.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a syntax error when setting up the user regulatory
hint. This change yields the same exact binary object though
so it ends up just being a syntax typo fix, fortunately.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 8bf3d79bc401ca417ccf9fc076d3295d1a71dbf5 enabled EEPROM
checksum checks to avoid bogus bug reports but failed to address
updating the code to consider devices with custom EEPROM sizes.
Devices with custom sized EEPROMs have the upper limit size stuffed
in the EEPROM. Use this as the upper limit instead of the static
default size. In case of a checksum error also provide back the
max size and whether or not this was the default size or a custom
one. If the EEPROM is busted we add a failsafe check to ensure
we don't loop forever or try to read bogus areas of hardware.
This closes bug 14874
http://bugzilla.kernel.org/show_bug.cgi?id=14874
Cc: stable@kernel.org
Cc: David Quan <david.quan@atheros.com>
Cc: Stephen Beahm <stephenbeahm@comcast.net>
Reported-by: Joshua Covington <joshuacov@googlemail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If multicast parameter (as returned by zd_op_prepare_multicast) has
changed, no bit in changed_flags is set. To handle this situation, we do
not return if changed_flags is 0. If we do so, we will have some issue
with IPv6 which uses multicast for link layer address resolution.
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tid is used as an array offset.
agg = &priv->stations[sta_id].tid[tid].agg;
iwl4965_tx_status_reply_tx(priv, agg, tx_resp, txq_id, index);
It should be limitted to MAX_TID_COUNT - 1;
struct iwl_tid_data tid[MAX_TID_COUNT];
regards,
dan carpenter
Signed-off-by: Dan Carpenter <error27@gmail.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there was an error acquiring the firmware lock in
mwl8k_configure_filter(), we would end up leaking the multicast
command packet prepared by mwl8k_prepare_multicast().
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The unit of sizeof() is byte instead of bit, so fix it.
The patch can fix debug output of some dma_addr_t variables.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add missing DEBUG_FS dependency for ATH9K_DEBUGFS in ath9k's Kconfig.
Signed-off-by: Dominik D. Geyer <dominik.geyer@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed a timeout bug in
/drivers/net/wireless/wl12xx/wl1271_spi.c
In the current code you cannot tell why you exited
the "poll for data ready" do-while loop if exiting
was done after the last possible loop.
Then timeout==0 regardless of (val & OCP_READY_MASK) or
!(val & OCP_READY_MASK), leading to possible false timeout...
Simple correction could be decreasing timeout after checking
for !(val & OCP_READY_MASK), not before
(Manually converted from email to an actual patch by me. -- JWL)
Reported-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To make it easier to notice cases of calling sleeping ops in atomic context,
annotate driver-ops.h with appropiate might_sleep() calls. At the same time,
also document in mac80211.h the op functions with missing contexts.
mac80211 doesn't seem to use get_tx_stats anywhere currently. Just to be on
the safe side, I documented it to be atomic, but hopefully the op can be
removed in the future.
Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen