Some error paths after the mthca_alloc_mailbox() call in mthca_modify_qp()
just do a "return -EINVAL" without freeing the mailbox. Convert these
returns to "goto out" to avoid leaking the mailbox storage.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor out common code for adding a userspace object to an idr into a
function idr_add_uobj(). This shrinks both the source and object code:
add/remove: 1/0 grow/shrink: 0/6 up/down: 57/-220 (-163)
function old new delta
idr_add_uobj - 57 +57
ib_uverbs_create_ah 543 512 -31
ib_uverbs_create_srq 662 630 -32
ib_uverbs_reg_mr 737 699 -38
ib_uverbs_create_cq 639 600 -39
ib_uverbs_alloc_pd 485 446 -39
ib_uverbs_create_qp 1020 979 -41
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In error paths when destroying an object, uverbs should not decrement
associated objects' usecnt, since ib_dereg_mr(), ib_destroy_qp(),
etc. already do that.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If ibdev->alloc_ucontext() fails then ib_uverbs_get_context() does not
unlock file->mutex before returning error.
Signed-off by: Ganapathi CH <cganapathi@novell.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use new ib_init_ah_from_wc() and ib_init_ah_from_path() helper
functions to clean up the IB CM.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a call to initialize address handle attributes given a path record.
This is used by the CM, and would be useful for users of UD QPs.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a function to initialize address handle attributes from a work
completion. This functionality is duplicated by both verbs and the CM.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The P_Key is provided into a SIDR REQ in two places, once as a
parameter, and again in the path record. Remove the P_Key as a
parameter and always use the one given in the path record.
This change has no practical effect on ABI functionality.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Misc cleanups in ib_srp:
1) I think that it is more efficient to move the req entries from req_list
to free_list in srp_reconnect_target (rather than rebuild the free_list).
(In any case this code is shorter).
2) This allows us to reuse code in srp_reset_device and srp_reconnect_target
and call a new function srp_reset_req.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There has been a change in the format of port identifiers between
revision 10 of the SRP specification and the current revision 16A.
Revision 10 specifies port identifier format as
lower 8 bytes : GUID upper 8 bytes : Extension
Whereas revision 16A specifies it as
lower 8 bytes : Extension upper 8 bytes : GUID
There are older targets (e.g. SilverStorm Virtual Fibre Channel
Bridge) which conform to revision 10 of the SRP specification.
The I/O class of revision 10 is 0xFF00 and the I/O class of revision
16A is 0x0100.
For supporting older targets, this patch:
1) Adds a new optional target creation parameter "io_class". Default
value of io_class is 0x0100 (i.e. revision 16A)
2) Uses the correct port identifier format for targets with IO class
of 0xFF00 (i.e. conforming to revision 10)
Signed-off-by: Ramachandra K <rkuchimanchi@silverstorm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add enum values for I/O Class values from rev. 10 and rev. 16a SRP
drafts. The values are used to detect targets that implement obsolete
revisions of SRP, so that the initiator can use the old format for
port identifier when connecting to them.
Signed-off-by: Ramachandra K <rkuchimanchi@silverstorm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When creating a FMR pool, query the IB device and use the returned
max_map_map_per_fmr attribute as for the max number of FMR remaps. If
the device does not suport querying this attribute, use the original
IB_FMR_MAX_REMAPS (32) default.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Report the true max_map_per_fmr value from mthca_query_device(),
taking into account the change in FMR remapping introduced by the
Sinai performance optimization.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change the mthca snoop of MADs that set PortInfo to check if the SM
has set the client reregister bit, and if it has, generate a client
reregister event. If the bit is not set, just generate a LID change
event as usual.
Signed-off-by: Leonid Arsh <leonida@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move ipath's struct port_info into <rdma/ib_smi.h>, so that it can be
used by mthca to implement client reregister support.
Remove the __attribute__((packed)) because all the members of the struct
are naturally aligned anyway.
Signed-off-by: Leonid Arsh <leonida@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Handle client reregister events by treating them just like LID or
SM changes -- flush all cached paths and rejoin multicast groups.
Signed-off-by: Leonid Arsh <leonida@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add IB_EVENT_CLIENT_REREGISTER to enum so low-level drivers can
generate "client reregister" events.
Signed-off-by: Leonid Arsh <leonida@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix misaligned access faults on ia64: never cast a misaligned
neighbour->ha + 4 pointer to union ib_gid type; pass a void * pointer
instead. The memcpy was being optimized to use full word accesses
because the compiler thought that union ib_gid is always aligned.
The cast in IPOIB_GID_ARG is safe, since it is fixed to access each
byte separately.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The comparisons of priv->tx_tail to ah->last_send in ipoib_free_ah()
and ipoib_post_receive() are slightly unsafe, because priv->tx_lock is
not held and hence a stale value of ah->last_send might be used, which
would lead to freeing an AH before the driver was really done with it.
The simple way to fix this is to the optimization of early free from
ipoib_free_ah() and unconditionally queue AHs for reaping, and then
take priv->tx_lock in __ipoib_reap_ah().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Check GID/LID for requester side when searching for request which
matches received response. This is in order to guarantee uniqueness
if the same TID is used when requesting via multiple source LIDs (when
LMC is not zero). Use ports' cached LMC to perform the check.
Further, do not perform LID check for direct-routed packets, since
the permissive LID makes a proper check impossible.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add an LMC cache to struct ib_device, and add a function
ib_get_cached_lmc() to query the cache.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
destroy_workqueue() already does flush_workqueue().
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
It's perfectly valid for a connection to an SRP target to have a
request limit of 0, so get rid of the message about it, which can spam
kernel logs even with printk_ratelimit(). Keep a count of such events
in a "zero_req_lim" SCSI host attribute instead, so someone who cares
can look at the statistics.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Handle IB_CM_DREQ_ERROR and IB_CM_DREQ_RECEIVED events from the CM,
instead of just printing "Unhandled CM event". In the case of
DREQ_ERROR, just ignore the event -- a TIMEWAIT_EXIT will be generated
also. For DREQ_RECEIVED, send a DREP in response to shut the
connection down cleanly.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make the sg_tablesize used by SRP adjustable at module load time via a
module parameter. Calculate the corresponding IU length required to
support this.
Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Allow userspace to throttle traffic on a given connection to a target
port by adding "max_cmd_per_lun=xyz" to lower the cmd_per_lun value
set for that scsi_host.
Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Interrupts will always be enabled in srp_remove_one(), so
spin_lock_irq() can be used instead of spin_lock_irqsave().
Also, the loop takes target->scsi_host->host_lock, so target->state
can just be set to SRP_TARGET_REMOVED witout testing the old value.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The SRP driver never sleeps while holding target_mutex, and it's just
used to protect some simple list operations, so hold times will be
short. So just convert it to a spinlock, which is smaller and faster.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
list_for_each_entry_safe() is used in one place where the list isn't
modified. So just change it to list_for_each_entry().
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
SCAN_WILD_CARD is indeed available from <scsi/scsi.h>, which is
already included. So get rid of private hack.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The kernel has had wait_for_completion_timeout() for a long time now.
mthca should use it to handle FW commands timing out, instead of
implementing the same thing in a much more complicated way by using
wait_for_completion() along with a timer that does complete().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Create an SRP FMR pool on HCAs that support FMRs, and use FMRs to map
gather/scatter lists that have more than one entry into a single
memory region that appears virtually contiguous to the SRP target
(which is the RDMA initiator).
This patch bails out on FMR mapping for SCSI commands where the
gather/scatter list cannot be mapped into a single FMR because there
are sub-page-sized entries in middle of the list. An unaligned
start or end of the list is OK.
Based on a patch by Vu Pham <vuhuong@mellanox.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Kernel connection management agent over InfiniBand that connects based
on IP addresses. The agent defines a generic RDMA connection
abstraction to support clients wanting to connect over different RDMA
devices.
The agent also handles RDMA device hotplug events on behalf of clients.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add an address translation service that maps IP addresses to
InfiniBand GID addresses using IPoIB.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Export ip_dev_find() to allow locating a net_device given an IP address.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Extend matching connection requests to listens in the InfiniBand CM to
include private data checks.
This allows applications to listen on the same service identifier,
with private data directing the request to the appropriate application.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Provide common handling for marshalling data between userspace clients
and kernel InfiniBand drivers.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Memfree firmware is in rare cases reporting WQE index == base - 1 in
receive completion with error, instead of (rq size - 1); base is 0 in
mthca. Here is a patch to avoid kernel crash and report a correct WR
id in this case.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca does not restore the following PCI-X/PCI Express registers after reset:
PCI-X device: PCI-X command register
PCI-X bridge: upstream and downstream split transaction registers
PCI Express : PCI Express device control and link control registers
This causes instability and/or bad performance on systems where one of
these registers is set to a non-default value by BIOS.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Reflect the fact that the Cell Broadband Engine supports 64k
pages by adding the bit to the CPU features.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The page size encoding passed to tlbie is incorrect for new-style
large pages. This fixes it. This doesn't affect anything on older
machines because mmu_psize_defs[psize].penc (the page size encoding)
is 0 for 4k and 16M pages (the two are distinguished by a separate "is
a large page" bit).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arm_timer() checks PF_EXITING to prevent BUG_ON(->exit_state)
in run_posix_cpu_timers().
However, for some reason it does so only for CPUCLOCK_PERTHREAD
case (which is imho wrong).
Also, this check is not reliable, PF_EXITING could be set on
another cpu without any locks/barriers just after the check,
so it can't prevent from attaching the timer to the exiting
task.
The previous patch makes this check unneeded.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
do_exit() clears ->it_##clock##_expires, but nothing prevents
another cpu to attach the timer to exiting process after that.
arm_timer() tries to protect against this race, but the check
is racy.
After exit_notify() does 'write_unlock_irq(&tasklist_lock)' and
before do_exit() calls 'schedule() local timer interrupt can find
tsk->exit_state != 0. If that state was EXIT_DEAD (or another cpu
does sys_wait4) interrupted task has ->signal == NULL.
At this moment exiting task has no pending cpu timers, they were
cleanuped in __exit_signal()->posix_cpu_timers_exit{,_group}(),
so we can just return from irq.
John Stultz recently confirmed this bug, see
http://marc.theaimsgroup.com/?l=linux-kernel&m=115015841413687
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the local timer interrupt happens just after do_exit() sets PF_EXITING
(and before it clears ->it_xxx_expires) run_posix_cpu_timers() will call
check_process_timers() with tasklist_lock + ->siglock held and
check_process_timers:
t = tsk;
do {
....
do {
t = next_thread(t);
} while (unlikely(t->flags & PF_EXITING));
} while (t != tsk);
the outer loop will never stop.
Actually, the window is bigger. Another process can attach the timer
after ->it_xxx_expires was cleared (see the next commit) and the 'if
(PF_EXITING)' check in arm_timer() is racy (see the one after that).
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Roland Dreier