As we initialize the default cctl value in the prep_* functions along
with the increment settings, we don't need to repeat the selection of
the AHB ports each time we create a LLI entry. Do this in the prep_*
functions once per transfer.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We don't need to initialize the cctl increment and protection values
in the runtime_config method - we have all the inforamtion to setup
these values in prep_slave_sg(). Move their initialization there.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Rather than modifying platform data while preparing a transfer, copy
the cctl value into the txd structure and modify the value there.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There is no need to wait until we start processing a tx descriptor
before setting up the DMA request selection in the ccfg register.
We know which channel and request will be used in prep_phy_channel(),
so setup the ccfg request selection at txd creation time in
prep_phy_channel().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The ccfg register is used to configure the channel parameters - the type
and direction of transfer, the flow control signal and IRQ mask enables.
The type and direction of transfer is known in the relevent prep_*
function where a txd is created. The IRQ mask enables are always set,
and the flow control signals are always set when we start processing a
txd according to phychan->signal.
If we store the ccfg value in the txd structure, we can avoid modifying
platform data - and even having it in platform data at all.
So, remove it from platform data too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As we now have all the code accessing the phychan {csrc,cdst,clli,cctl,
ccfg} members in one function, there's no point storing the data into
the struct. Get rid of the struct members. Re-order the register dump
in the dev_dbg() to reflect the order we write the registers to the DMA
device.
The txd {csrc,cdst,clli,cctl} values are duplicates of the lli[0]
values, so there's no point duplicating these either. Program the DMAC
registers directly from the lli[0] values.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There is no need for pl08x_config_phychan_for_txd(), pl08x_set_cregs()
and pl08x_enable_phy_chan() to be separate - they are always called in
sequence. Combine them into one function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As the LLI list is an array, we can use maths to locate which LLI
index we're currently at, and then sum up the remaining LLI entries
until we reach the end of the list.
This makes the code much easier to read, and much less susceptible
to falling off the end of the array.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The LLI pointer in the documentation is placed into the LLI register,
so name it LLI rather than 'next'.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use 'u32' for the LLI structure members, which are defined by hardware
to be 32-bit. dma_addr_t is much more vague about its actual size.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use size_t for variables denoting lengths throughout, and use the 'z'
qualifier for printing the value. For safety, add a BUG_ON() in
pl08x_fill_lli_for_desc() to catch the remainder potentially becoming
negative.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
llis_bus is the DMA address of the LLI array. Casting it to be a
pointer just to be able to use pointer arithmetic on it is not nice.
We can trivially deal with the places where we do arithmetic on it,
and it's actually cleaner this way.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We only want use the address of the LLI pointer when locating the
corresponding structure in memory, so clear the master bus selection
bit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tight loops should use cpu_relax() to allow CPUs to reduce power
consumption while waiting for events.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Consolidate duplicated channel release code into release_phy_channel()
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Consolidate code which allocates and initializes txds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Avoid using 'void *' struct fields when the structs are not defined
in linux/amba/pl08x.h - instead, forward declare the struct names, and
use these instead. This ensures we have proper typechecking.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We should never modify the vendor data structure so make it const.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The driver already won't initialize a channel with a circular buffer;
the check in pl08x_prep_channel_resources() sees to that. Remove
circular buffer support for the time being.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The tasklet always is initialized with a non-NULL data argument. It
is not possible for it to be called with a NULL data argument (unless
something is very wrong in the tasklet code - in which case lots of
stuff will break). Therefore, as plchan can never be NULL, remove
this unnecessary BUG check.
In pl08x_tasklet(), we've already dereferenced plchan->at, so it can't
be NULL here. Remove this unnecessary BUG check.
pl08x_fill_llis_for_desc() and pl08x_free_txd() are always called with
a non-NULL txd argument - either as a consequence of the code paths or
as a result of other checks already in place. We don't need to repeat
the non-NULL check in these functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We don't need to include linux/pci.h as we aren't a PCI driver. We
aren't doing any processor specific functions, so asm/processor.h is
not required. asm/cacheflush.h shouldn't be used, we have the DMA API
for this. DMA interfaces aren't required as we're only implementing
the dmaengine API and not a platform-private DMA API.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A driver which emits both decimal and hex numbers in its printk
creates confusion as to what is what. Prefix hex numbers with 0x.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Include the revision number of the PL08x primecell in the boot-time
printk to allow proper identification of the peripheral. Reformat
the announcement printk format reflect what we do for other primecell
drivers - generally "PLXXX revX at 0xNNNNNNNN irq X".
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Explain the two flow control methods which the PL08x implements, along
with the problem which peripheral flow control presents. This helps
people understand why we are unable to use these DMA controllers with
(eg) the MMCI.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
drivers/dma/amba-pl08x.c:1895:40: warning: Unknown escape '%'
drivers/dma/amba-pl08x.c:1903:40: warning: Unknown escape '%'
drivers/dma/amba-pl08x.c:513:6: warning: symbol 'pl08x_choose_master_bus' was not declared. Should it be static?
drivers/dma/amba-pl08x.c:604:5: warning: symbol 'pl08x_fill_llis_for_desc' was not declared. Should it be static?
drivers/dma/amba-pl08x.c:1442:32: warning: symbol 'pl08x_prep_slave_sg' was not declared. Should it be static?
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Trying to disable a tasklet while holding a spinlock which the tasklet
will take is a recipe for deadlock - tasklet_disable() will wait for the
tasklet to finish running, which it will never do. In any case, there
is not a corresponding tasklet_enable(), so once the tasklet is disabled,
it will never run again until reboot.
It's safe to just remove the tasklet_disable() as we remove all current
and pending descriptors before releasing this spinlock. This means that
the tasklet will find no remaining work if it subsequently runs.
The only remaining issue is that the callback for an already submitted
txd may be in progress, or even called after terminate_all() returns.
There's not much that can be done about that as waiting for the callback
to complete before returning will also lead to deadlocks.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
pl08x_issue_pending() returns with the spinlock locked and interrupts
disabled if the channel is waiting for a physical DMA to become free.
This is wrong - especially as pl08x_issue_pending() is an API function
as it leads to deadlocks. Fix it to always return with the spinlock
unlocked.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If we fail to allocate the LLI, the prep_* function will return NULL.
However, the TXD we allocated will not be placed on any list, nor
will it be freed - we'll just drop all references to it. Make sure
we free it rather than leaking TXDs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tasklets are run from an interruptible context. The slave DMA functions
can be called from within IRQ handlers. Taking the spinlock without
disabling interrupts allows an interrupt handler to run, which may try
to take the spinlock again, resulting in deadlock. Fix this by using
the irqsave spinlocks.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The last_issued variable uses an atomic type, which is only
incremented inside a protected region, and then read. Everywhere else
only reads the value, so it isn't using atomic_t correctly, and it
doesn't even need to. Moreover, the DMA engine code provides us with
a variable for this already - chan.cookie. Use chan.cookie instead.
Also, avoid negative dma_cookie_t values - negative returns from
tx_submit() mean failure, yet in reality we always succeed. Restart
from cookie 1, just like other DMA engine drivers do.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If maxburst was passed in as zero, we would overflow the burst_sizes[]
array. Fix this by checking for this condition, and defaulting to
single transfer 'bursts'.
Improve the readability of the loop using a for() loop rather than
a while() loop with the iterator initialized far from the loop.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Correct mis-spellings in comments and printk strings.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
PowerPC relies on IRQ-disable to guard against RCU quiecent states,
use the appropriate RCU call version.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This reverts commit e0fdace10e.
On-list discussion seems to suggest that the robustness fixes for printk
make this unnecessary and DaveM has also agreed in person at Kernel Summit
and on list.
The main problem with this code is once we hit a lockdep splat we always
keep oops_in_progress set, the console layer uses oops_in_progress with KMS
to decide when it should be showing the oops and not showing X, so it causes
problems around suspend/resume time when a userspace resume can cause a console
switch away from X, only if oops_in_progress is set (which is what we want
if an oops actually is in progress, but not because we had a lockdep splat
2 days prior).
Cc: David S Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP2+: PM/serial: hold console semaphore while OMAP UARTs are disabled
OMAP: UART: don't resume UARTs that are not enabled.
Some Lenovos have TPMs that require a quirk to function correctly. This can
be autodetected by checking whether the device has a _HID of INTC0102. This
is an invalid PNPid, and as such is discarded by the pnp layer - however
it's still present in the ACPI code, so we can pull it out that way. This
means that the quirk won't be automatically applied on non-ACPI systems,
but without ACPI we don't have any way to identify the chip anyway so I
don't think that's a great concern.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Tested-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Andy Isaacson <adi@hexapodia.org>
Signed-off-by: James Morris <jmorris@namei.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (24 commits)
Btrfs: don't use migrate page without CONFIG_MIGRATION
Btrfs: deal with DIO bios that span more than one ordered extent
Btrfs: setup blank root and fs_info for mount time
Btrfs: fix fiemap
Btrfs - fix race between btrfs_get_sb() and umount
Btrfs: update inode ctime when using links
Btrfs: make sure new inode size is ok in fallocate
Btrfs: fix typo in fallocate to make it honor actual size
Btrfs: avoid NULL pointer deref in try_release_extent_buffer
Btrfs: make btrfs_add_nondir take parent inode as an argument
Btrfs: hold i_mutex when calling btrfs_log_dentry_safe
Btrfs: use dget_parent where we can UPDATED
Btrfs: fix more ESTALE problems with NFS
Btrfs: handle NFS lookups properly
btrfs: make 1-bit signed fileds unsigned
btrfs: Show device attr correctly for symlinks
btrfs: Set file size correctly in file clone
btrfs: Check if dest_offset is block-size aligned before cloning file
Btrfs: handle the space_cache option properly
btrfs: Fix early enospc because 'unused' calculated with wrong sign.
...
Its easy to eat all kernel memory and trigger NMI watchdog, using an
exploit program that queues unix sockets on top of others.
lkml ref : http://lkml.org/lkml/2010/11/25/8
This mechanism is used in applications, one choice we have is to have a
recursion limit.
Other limits might be needed as well (if we queue other types of files),
since the passfd mechanism is currently limited by socket receive queue
sizes only.
Add a recursion_level to unix socket, allowing up to 4 levels.
Each time we send an unix socket through sendfd mechanism, we copy its
recursion level (plus one) to receiver. This recursion level is cleared
when socket receive queue is emptied.
Reported-by: Марк Коренберг <socketpair@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong of initializer entry was modified.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Reported-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver's AUTHOR was changed to "Toshiharu Okada" from "Masayuki Ohtake".
I update the Kconfig, renamed "Topcliff" to "EG20T".
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 58933c64(ucc_geth: Fix the wrong the Rx/Tx FIFO size),
the UCC_GETH_UTFTT_INIT is set to 512 based on the recommendation
of the QE Reference Manual. But that will sometimes cause tx halt
while working in half duplex mode.
According to errata draft QE_GENERAL-A003(High Tx Virtual FIFO
threshold size can cause UCC to halt), setting UTFTT less than
[(UTFS x (M - 8)/M) - 128] will prevent this from happening
(M is the minimum buffer size).
The patch changes UTFTT back to 256.
Signed-off-by: Li Yang <leoli@freescale.com>
Cc: Jean-Denis Boyer <jdboyer@media5corp.com>
Cc: Andreas Schmitz <Andreas.Schmitz@riedel.net>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet sockets corresponding to passive connections are added to the bind hash
using ___inet_inherit_port(). These sockets are later removed from the bind
hash using __inet_put_port(). These two functions are not exactly symmetrical.
__inet_put_port() decrements hashinfo->bsockets and tb->num_owners, whereas
___inet_inherit_port() does not increment them. This results in both of these
going to -ve values.
This patch fixes this by calling inet_bind_hash() from ___inet_inherit_port(),
which does the right thing.
'bsockets' and 'num_owners' were introduced by commit a9d8f9110d
(inet: Allowing more than 64k connections and heavily optimize bind(0))
Signed-off-by: Nagendra Singh Tomar <tomer_iisc@yahoo.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds some debug information about ehea not being able to
allocate enough spaces. Also it correctly updates the amount of available
skb.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King - ARM Linux