When the host controller dies or is removed while a device is plugged in,
the USB core will attempt to deallocate the struct usb_device. That will
call into xhci_free_dev(). This function used to attempt to submit a
disable slot command to the host controller and clean up the device
structures when that command returned. Change xhci_free_dev() to skip the
command submission and just free the memory if the host controller died.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the host controller dies (e.g. it is removed from a PCI card slot),
the xHCI driver cannot expect commands to complete. The buggy code this
patch fixes would mark an URB as canceled and then expect the URB to be
completed when the stop endpoint command completed. That would never
happen if the host controller was dead, so the USB core would just hang in
the disconnect code.
If the host controller died, and the driver asks to cancel an URB, free
any structures associated with that URB and immediately give it back.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the host controller card is removed from the system, stop the timer
function to debug the xHCI rings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current 10ms timeout is too short for some normal USBTMC device
operation, increase it to a value which was tested with previously
affected Tektronix oscilloscopes.
Signed-off-by: Gergely Imreh <imrehg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stanse found a memory leak in lcd_probe. Instead of returning without
releasing the memory, jump to the error label which frees it.
http://stanse.fi.muni.cz/
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Updated sierra driver version from 1.3.7 to 1.3.8 now that the autosuspend
capabilities were added to the driver.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1295) fixes a recently-added bug in the USB serial core.
If certain kinds of errors occur during probing, the core may call a
serial driver's release method without previously calling the attach
method. This causes some drivers (io_ti in particular) to perform an
invalid memory access.
The patch adds a new flag to keep track of whether or not attach has
been called.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jean-Denis Girard <jd.girard@sysnux.pf>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a regression introduced in
39892da44b.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Re-structure read processing.
- Kill obsolete work queue and always push to tty in completion handler.
- Use tty_insert_flip_string instead of per character push when
possible.
- Fix stalled-read regression in 2.6.31 by using urb status to
determine when port is closed rather than port count.
- Fix race with open/close by checking ASYNCB_INITIALIZED in
unthrottle.
- Kill private rx_flag and lock and use throttle flags in
usb_serial_port instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove superfluous error checks in completion handler:
- No need to check private data and urb pointers as we check urb-status
before dereferencing priv (which is not freed until urb has been killed
on close).
- No need to check tty as it is checked again when processing.
- No need to check urb->number_of_packets on bulk urb.
Note that both private data and tty are checked again before processing
(possibly from work queue which also is cancelled on close).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove unused rx_byte counter which is never exposed as noted by Alan
Cox.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes tty_flip_buffer_push being called from hard interrupt context with
low_latency set.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_atp867x: add Power Management support
pata_atp867x: PIO support fixes
pata_atp867x: clarifications in timings calculations and cable detection
pata_atp867x: fix it to not claim MWDMA support
libata: fix incorrect link online check during probe
ahci: filter FPDMA non-zero offset enable for Aspire 3810T
libata: make gtf_filter per-dev
libata: implement more acpi filtering options
libata: cosmetic updates
ahci: display all AHCI 1.3 HBA capability flags (v2)
pata_ali: trivial fix of a very frequent spelling mistake
ahci: disable 64bit DMA by default on SB600s
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
futex: fix requeue_pi key imbalance
futex: Fix typo in FUTEX_WAIT/WAKE_BITSET_PRIVATE definitions
rcu: Place root rcu_node structure in separate lockdep class
rcu: Make hot-unplugged CPU relinquish its own RCU callbacks
rcu: Move rcu_barrier() to rcutree
futex: Move exit_pi_state() call to release_mm()
futex: Nullify robust lists after cleanup
futex: Fix locking imbalance
panic: Fix panic message visibility by calling bust_spinlocks(0) before dying
rcu: Replace the rcu_barrier enum with pointer to call_rcu*() function
rcu: Clean up code based on review feedback from Josh Triplett, part 4
rcu: Clean up code based on review feedback from Josh Triplett, part 3
rcu: Fix rcu_lock_map build failure on CONFIG_PROVE_LOCKING=y
rcu: Clean up code to address Ingo's checkpatch feedback
rcu: Clean up code based on review feedback from Josh Triplett, part 2
rcu: Clean up code based on review feedback from Josh Triplett
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Set correct normal_prio and prio values in sched_fork()
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: user local buffer variable for trace branch tracer
tracing: fix warning on kernel/trace/trace_branch.c andtrace_hw_branches.c
ftrace: check for failure for all conversions
tracing: correct module boundaries for ftrace_release
tracing: fix transposed numbers of lock_depth and preempt_count
trace: Fix missing assignment in trace_ctxwake_*
tracing: Use free_percpu instead of kfree
tracing: Check total refcount before releasing bufs in profile_enable failure
* 'sparc-perf-events-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
mm, perf_event: Make vmalloc_user() align base kernel virtual address to SHMLBA
perf_event: Provide vmalloc() based mmap() backing
* 'perf-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_events: Make ABI definitions available to userspace
perf tools: elf_sym__is_function() should accept "zero" sized functions
tracing/syscalls: Use long for syscall ret format and field definitions
perf trace: Update eval_flag() flags array to match interrupt.h
perf trace: Remove unused code in builtin-trace.c
perf: Propagate term signal to child
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, timers: Check for pending timers after (device) interrupts
NOHZ: update idle state also when NOHZ is inactive
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ice1724: increase SPDIF and independent stereo buffer sizes
ALSA: opl3: circular locking in the snd_opl3_note_on() and snd_opl3_note_off()
ALSA: ICE1712/24 - Change the Multi Track Peak control (level meters) from MIXER to PCM type
ALSA: hda - Fix yet another auto-mic bug in ALC268
ASoC: WM8350 capture PGA mutes are inverted
ASoC: Remove absent SYNC and TDM DAI format options from i.MX SSI
sound: via82xx: move DXS volume controls to PCM interface
ALSA: hda - Don't pick up invalid HP pins in alc_subsystem_id()
ALSA: hda - Add a workaround for ASUS A7K
ALSA: hda - Fix invalid initializations for ALC861 auto mode
ASoC: wm8940: Fix check on error code form snd_soc_codec_set_cache_io
ASoC: Fix SND_SOC_DAPM_LINE handling
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (24 commits)
drm/radeon/kms: fix vline register for second head.
drm/r600: avoid assigning vb twice in blit code
drm/radeon: use list_for_each_entry instead of list_for_each
drm/radeon/kms: Fix AGP support for R600/RV770 family (v2)
drm/radeon/kms: Fallback to non AGP when acceleration fails to initialize (v2)
drm/radeon/kms: Fix RS600/RV515/R520/RS690 IRQ
drm/radeon: Fix setting of bits
drm/ttm: fix refcounting in ttm global code.
drm/fb: add more correct 8/16/24/32 bpp fb support.
drm/fb: add setcmap and fix 8-bit support.
drm/radeon/kms: respect single crtc cards, only create one crtc. (v2)
drm: Delete the DRM_DEBUG_KMS in drm_mode_cursor_ioctl
drm/radeon/kms: add support for "Surround View"
drm/radeon/kms: Fix irq handling on AVIVO hw
drm/radeon/kms: R600/RV770 remove dead code and print message for wrong BIOS
drm/radeon/kms: Fix R600/RV770 disable acceleration path
drm/radeon/kms: Fix R600/RV770 startup path & reset
drm/radeon/kms: Fix R600 write back buffer
drm/radeon/kms: Remove old init path as no hw use it anymore
drm/radeon/kms: Convert RS600 to new init path
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (40 commits)
ethoc: limit the number of buffers to 128
ethoc: use system memory as buffer
ethoc: align received packet to make IP header at word boundary
ethoc: fix buffer address mapping
ethoc: fix typo to compute number of tx descriptors
au1000_eth: Duplicate test of RX_OVERLEN bit in update_rx_stats()
netxen: Fix Unlikely(x) > y
pasemi_mac: ethtool get settings fix
add maintainer for network drop monitor kernel service
tg3: Fix phylib locking strategy
rndis_host: support ETHTOOL_GPERMADDR
ipv4: arp_notify address list bug
gigaset: add kerneldoc comments
gigaset: correct debugging output selection
gigaset: improve error recovery
gigaset: fix device ERROR response handling
gigaset: announce if built with debugging
gigaset: handle isoc frame errors more gracefully
gigaset: linearize skb
gigaset: fix reject/hangup handling
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6:
Revert "Revert "ide: try to use PIO Mode 0 during probe if possible""
sis5513: fix PIO setup for ATAPI devices
Now that range timers and deferred timers are common, I found a
problem with these using the "perf timechart" tool. Frans Pop also
reported high scheduler latencies via LatencyTop, when using
iwlagn.
It turns out that on x86, these two 'opportunistic' timers only get
checked when another "real" timer happens. These opportunistic
timers have the objective to save power by hitchhiking on other
wakeups, as to avoid CPU wakeups by themselves as much as possible.
The change in this patch runs this check not only at timer
interrupts, but at all (device) interrupts. The effect is that:
1) the deferred timers/range timers get delayed less
2) the range timers cause less wakeups by themselves because
the percentage of hitchhiking on existing wakeup events goes up.
I've verified the working of the patch using "perf timechart", the
original exposed bug is gone with this patch. Frans also reported
success - the latencies are now down in the expected ~10 msec
range.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Tested-by: Frans Pop <elendil@planet.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <20091008064041.67219b13@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When a vmalloc'd area is mmap'd into userspace, some kind of
co-ordination is necessary for this to work on platforms with cpu
D-caches which can have aliases.
Otherwise kernel side writes won't be seen properly in userspace
and vice versa.
If the kernel side mapping and the user side one have the same
alignment, modulo SHMLBA, this can work as long as VM_SHARED is
shared of VMA and for all current users this is true. VM_SHARED
will force SHMLBA alignment of the user side mmap on platforms with
D-cache aliasing matters.
The bulk of this patch is just making it so that a specific
alignment can be passed down into __get_vm_area_node(). All
existing callers pass in '1' which preserves existing behavior.
vmalloc_user() gives SHMLBA for the alignment.
As a side effect this should get the video media drivers and other
vmalloc_user() users into more working shape on such systems.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <200909211922.n8LJMYjw029425@imap1.linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
agp: parisc-agp.c - use correct page_mask function
parisc: Fix linker script breakage.
parisc: convert to asm-generic/hardirq.h
parisc: Make THREAD_SIZE available to assembly files and linker scripts.
parisc: correct use of SHF_ALLOC
parisc: rename parisc's vmalloc_start to parisc_vmalloc_start
parisc: add me to Maintainers
parisc: includecheck fix: signal.c
parisc: HAVE_ARCH_TRACEHOOK
parisc: add skeleton syscall.h
parisc: stop using task->ptrace for {single,block}step flags
parisc: split syscall_trace into two halves
parisc: add missing TI_TASK macro in syscall.S
parisc: tracehook_signal_handler
parisc: tracehook_report_syscall
The PC Card 8.0 specification (vol. 4, section 3.2.10) says the
TPLLV1_INFO field of the CISTPL_VERS_1 tuple must contain 4 strings. Some
cards don't have all 4 so just parse as many as we can.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Tested-by: Jonathan Cameron <jic23@cam.ac.uk>
Tested-by: Bing Zhao <bzhao@marvell.com>
Cc: Roel Kluin <roel.kluin@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For hwpoison stress testing. The debugfs mount point is assumed to be
/debug/.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Refactor the code to be more modular and easier to reuse.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This helps merge duplicate code (now and future) and outstand the main
logic.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It indicates to the system admin that processes mapping such pages may be
eating less physical memory than the reported numbers by legacy tools.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Izik Eidus <ieidus@redhat.com>
Acked-by: Chris Wright <chrisw@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This flag indicates a hardware detected memory corruption on the page.
Any future access of the page data may bring down the machine.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update documentation of cgroups tasks and procs files
Document the cgroup.procs file.
Clarify the semantics of the cgroup.procs and tasks files. Although the
current cgroup.procs interface returns a sorted and uniqified list of
pids, potential future performance enhancements could result in those
properties being removed - explicitly document this aspect of the API.
There are no existing users of cgroup.procs, so compatibility isn't an
issue. There are users of the "tasks" file, but none that would appear to
break in the event of the sorted property being broken. The standard
"libcpuset" explicitly sorts the results of reading from the tasks file,
and "libcg" and other users don't appear to care about ordering.
Signed-off-by: Paul Menage <menage@google.com>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fix the following 'make includecheck' warning:
drivers/video/da8xx-fb.c: linux/device.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fix the following 'make includecheck' warning:
drivers/video/msm/mddi.c: linux/delay.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fix the following 'make includecheck' warning:
fs/proc/kcore.c: linux/mm.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fix the following 'make includecheck' warning:
mm/vmalloc.c: linux/highmem.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adjust the max_kernel_pages default to a quarter of totalram_pages,
instead of nr_free_buffer_pages() / 4: the KSM pages themselves come from
highmem, and even on a 16GB PAE machine, 4GB of KSM pages would only be
pinning 32MB of lowmem with their rmap_items, so no need for the more
obscure calculation (nor for its own special init function).
There is no way for the user to switch KSM on if CONFIG_SYSFS is not
enabled, so in that case default run to KSM_RUN_MERGE.
Update KSM Documentation and Kconfig to reflect the new defaults.
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Izik Eidus <ieidus@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sarah Sharp