Instead of hard-coding the SM PS mode per hardware,
this makes iwlwifi support the new mac80211 API for
controlling the SM PS mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The zd1211rw always assumed that the storage device is at endpoint 1,
but there are devices (Spairon Homelink 1202) that are at endpoint 0.
Try both, starting with 1 to make sure to not break existing setups.
Signed-off-by: Stefan Seyfried <seife@sphairon.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IEEE-802.11n spec says the RX highest data rate field does
not specify the highest supported RX data rate if its not set.
Ignore it if not set then. Refer to section 7.3.56.4
Cc: johannes@sipsolutions.net
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When debugging you want to be lazy and not have to parse
bits yourself so let mac80211 debugfs do the parsing for you.
This is what I get against my WRT610N:
root@tux:~# cat /sys/kernel/debug/ieee80211/phy0/stations/00\:22\:6b\:aa\:bb\:01/ht_capa
ht supported
cap: 0x000e
HT20/HT40
SM Power Save disabled
No RX STBC
Max AMSDU length: 7935 bytes
No DSSS/CCK HT40
ampdu factor/density: 2/6
MCS mask: ff ff 00 00 00 00 00 00 00 00
MCS rx highest: 0
MCS tx params: 0
Cc: johannes@sipsolutions.net
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MCS set is 16 bits so when debugging ensure the full 16 bits
are represented. Current reading would make you think its only
8 bits.
Cc: johannes@sipsolutions.net
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since mac80211_hwsim supports multiple virtual interfaces, we need to
iterate through all active interfaces when figuring out whether there
is a match during TX Ack status checking. This fixes TX status
reporting for cases where secondary interfaces are used.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hw rate control is used, these parameters have
no meaning because the hardware cannot get at them
right now, so disallow setting them. Also clean up
the function a bit.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Determine the offset at compile time.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This variable was once set to WLAN_CAPABILITY_SHORT_PREAMBLE and
there's no code that could change the variable to something else.
Therefore it seems this is not necessary :-)
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mostly for the embedded people that know beforehand that they don't need
MESH at all and want to save some bytes, but also helpful for the upcoming
cfg80211 transition.
text data bss dec hex filename
114264 2308 140 116712 1c7e8 libertas.ko with mesh
105026 2000 140 107166 1a29e libertas.ko without mesh
--------------------------------------------------
-9238 -308 -9546
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While it's might be technically true that only MESH-enabled firmwares
are also RTAP-enabled, I like to have this decoupled.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mesh_autostart_enabled was nowhere set. Rumor is that this is used in the
OLPC tree, but they never did submit their code upstream.
After removing this code, it turned out that the sync_channel stuff is now
also unused, so get rid of that as well.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both variables contained the same information (no mesh, old mesh, new mesh).
So we can get rid of one variable.
Also move the mesh-version test from cmd.c into mesh.c.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean out some cruft that could use an already existing
sta_info struct -- that case cannot happen. Also, there's
a bug there -- if allocation/insertion fails then it is
possible that we are left in a lingering state where
mac80211 waits for the AP, cfg80211 waits for mac80211,
but the AP has already replied. Since there's no way to
indicate an internal error, pretend there was a timeout,
i.e. that the AP never responded.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before
commit ca9034592823e8179511e48a78731f95bfdd766c
Author: Holger Schurig <hs4233@mail.mn-solutions.de>
Date: Tue Oct 13 13:45:28 2009 +0200
cfg80211: remove warning in deauth case
we assumed that drivers never give us spurious deauth
frames because they filter them out based on the auth
state they keep track of. This turned out to be racy,
because userspace might deauth while the AP is also
sending a deauth frame, so the warning was removed.
However, in that case we should not tell userspace
about the AP's frame if it requested deauth "first",
where "first" means it came to cfg80211 first.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some situations it is required that a system be
configured with no support for 40 MHz channels in
the 2.4 GHz band. Rather than imposing any such
restrictions on everybody, allow configuration a
system like that with a module parameter. It is
writable at runtime but only takes effect at the
time of the next association.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not that we actually ever aggregate anything, but
it could potentially be useful anyhow to simulate
aggregation sessions.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable spatial multiplexing in mac80211 by telling the
driver what to do and, where necessary, sending action
frames to the AP to update the requested SMPS mode.
Also includes a trivial implementation for hwsim that
just logs the requested mode.
For now, the userspace interface is in debugfs only,
and let you toggle the requested mode at any time.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the device receives an A-MSDU frame (indicated by flag
IWM_RX_TICKET_AMSDU_MSK), use ieee80211_amsdu_to_8023s to convert
it to a list of 802.3 frames and handled them to upper layer.
Cc: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the A-MSDU handling code from mac80211 to cfg80211 so that more
drivers can use it. The new created function ieee80211_amsdu_to_8023s
converts an A-MSDU frame to a list of 802.3 frames.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 tkip code won't call update_tkip_key, if rx packets
are received without KEY_FLAG_UPLOADED_TO_HARDWARE. This can happen on
first packet because the hardware key stuff is called asynchronously with
todo workqueue.
This patch workaround that by tracking if we sent the key to the driver.
Signed-off-by: Gregor Kowski <gregor.kowski@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure that frames without payload are properly trimmed in
rt2x00queue_insert_l2pad.
This should fix the bug reported by Benoit Papillault in:
http://marc.info/?l=linux-wireless&m=125974773006734&w=2
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to Ralink source code, the RX frame format is RXINFO + RXWI +
802.11 frame + RXD, including various padding. Before this patch, we
were using RXD + RXWI + 802.11 frame, so RXD was not correct.
Doing this, we fix the L2PAD bit which is now correctly set on received
frames.
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX aggregation is a way to receive multiple 802.11 frames in one RX buffer.
However, we don't know yet how to handle this case in rt2800usb_fill_rxdone
and this has probably no impact on RX performance as well, so we disable it
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
L2 padding will only be present when there is actual payload present.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify the rt2x00queue_insert_l2pad function by handling the alignment
operations one by one. Do not special case special circumstances.
Basically first perform header alignment, and then perform payload alignment
(if any payload does exist). This results in a properly aligned skb.
The end result is better readable code, with better results, as now L2 padding
is inserted only when a payload is actually present in the frame.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the improved L2 padding code, this flag is no longer necessary, as the
rt2x00queue_remove_l2pad is capable of detecting by itself if L2 padding is
applied.
For received frames the RX descriptor flag is still being checked.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a couple of more bugs in the L2 padding code:
1. Compute the amount of L2 padding correctly (in 3 places).
2. Trim the skb correctly when the L2 padding has been applied.
Also introduce a central macro the compute the L2 padding size.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise we end up truncating the skb before removing the l2pad
thus we might have the truncated part become garbage while getting
it back in remove_l2pad.
For the same issue: remove the skb_trim from the rt2800 fill_rxdone
(it is done after l2pad removal in rt2x00lib_rxdone).
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not include timestamp for a frame that has been injected
through a monitor interface.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The padding is to be added between header and payload for the only header need
padding case.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
platform rfkill is async thus we may try to read while the device is
already off.
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kenichi HORIO <moattailk1@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not need to log error when fail the sensitivity command, driver will send
sensitivity write command to uCode after each sensitivity calibration if
station is associated with AP. It is a normal case when user unload the module
or shutdown the system while still associated with the AP, since uCode already
on the way down, it will not reply the sensitivity write request; report
error in this case will give misleading information, remove the error checking
here to provide a clean shutdown if no other error detected.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature enables the on-screen uCode event log dump. The original
method will append the event log to syslog; with this capability,
we also enable the user to write script to capture the
events which provide additional flexibility to help uCode debugging
Method
1) change to debugfs directory (sys/kernel/debug/phyX/iwlagn/data)
2) #cat log_event
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to help uCode debugging, adding the capability to provide
continuous uCode event logging function.
uCode events is located in round-robin event queue and filled by uCode,
by enable continuous event logging, driver check the write pointer
and log the newly added events in iwl_bg_ucode_trace() timer function.
There is still possibility of missing events if event queue being
wrapped before next event dump; but with this capability, we can have
much better understanding of the uCode behavior during runtime; it can
help to debug the uCode related issues.
Methods to enable/disable the continuous event log:
step 1: enable ucode trace timer
"echo 1 >
/sys/kernel/debug/ieee80211/phyX/iwlagn/debug/ucode_tracing"
step 2: start ftrace
sudo ./trace-cmd record -e iwlwifi_ucode:* sleep 1d
step 3: stop ftrace
sudo ./trace-cmd report trace.dat
step 4: disable ucode trace timer
"echo 0 >
/sys/kernel/debug/ieee80211/phyX/iwlagn/debug/ucode_tracing"
use "ucode_tracing" debugfs file to display number of event
queue wrapped when driver attempt the continuous event logging. If event
queue being wrapped more than once when driver has opportunity to log
the event; it indicated there are events missing in the event log trace.
This continuous event log function only available for 4965 and newer
NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When uCode HW/SW error detected, dumping important CSR (Control and Status
Registers) values.
Also add "csr" debugfs file to dump the current values of CSR defined in
CSR table to syslog.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change name from RF_CARD_DISABLED to CT_CARD_DISABLED to match the
indication from uCode, also log the debug message when the condition
detected in iwl_rx_card_state_notif()
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch provides infrastructure for machine translation of the
regulatory rules database used by CRDA into a C data structure.
It includes code for searching that database as an alternative
to dynamic regulatory rules updates via CRDA. Most people should
use CRDA instead of this infrastructure, but it provides a better
alternative than the WIRELESS_OLD_REGULATORY infrastructure (which
can now be removed).
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The payload alignment warning enabled by MAC80211_DEBUG_PACKET_ALIGNMENT is
difficult. To fix it, a firmware change is needed but in most cases that's
very difficult. So the benefit from the warning is low and most probably
it just creates more confusion for people who just enable all warnings
(like it did for me).
Remove the unaligned IP payload warning and the kconfig option. But
leave the unaligned packet warning, it will be enabled with
MAC80211_VERBOSE_DEBUG.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When building rtl8180, the following warning occurs:
CC [M] drivers/net/wireless/rtl818x/rtl8180_dev.o
drivers/net/wireless/rtl818x/rtl8180_dev.c: In function ‘rtl8180_handle_rx’:
drivers/net/wireless/rtl818x/rtl8180_dev.c:135: warning: ‘qual’ is deprecated
(declared at include/net/mac80211.h:562)
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wlan didn't copy module parameters for bcm4320a to private structure.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Everything is ready now and we can enable WMM in mac80211.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg