This patch implement the sender side for SACK-IMMEDIATELY
extension.
Section 4.1. Sender Side Considerations
Whenever the sender of a DATA chunk can benefit from the
corresponding SACK chunk being sent back without delay, the sender
MAY set the I-bit in the DATA chunk header.
Reasons for setting the I-bit include
o The sender is in the SHUTDOWN-PENDING state.
o The application requests to set the I-bit of the last DATA chunk
of a user message when providing the user message to the SCTP
implementation.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
This patch implement the receiver side for SACK-IMMEDIATELY
extension:
Section 4.2. Receiver Side Considerations
On reception of an SCTP packet containing a DATA chunk with the I-bit
set, the receiver SHOULD NOT delay the sending of the corresponding
SACK chunk and SHOULD send it back immediately.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
This patch implement the definition for SACK-IMMEDIATELY
extension.
Section 3. The I-bit in the DATA Chunk Header
The following Figure 1 shows the extended DATA chunk.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 0 | Res |I|U|B|E| Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TSN |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Stream Identifier | Stream Sequence Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Payload Protocol Identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
\ \
/ User Data /
\ \
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1
The only difference between the DATA chunk in Figure 1 and the DATA
chunk defined in [RFC4960] is the addition of the I-bit in the flags
field of the chunk header.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
There appears to be a stray setting of the VFE bit when registering vlans.
This should not be done as vlan filtering should be enabled any time the
interface is not in promiscous mode
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While configuring rscctl use rx buffer length from rx ring structure
instead of passing rx_buf_len to ixgbe_configure_rscctl
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Divide 82599 HWRSC counters into aggregated and flushed to count number of
packets getting coalesced per TCP connection.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can run out of mccq wrbs when completions don't arrive
due to an unresponsive card. This must not hit a BUG_ON(); instead
log a msg and return an error.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling msix was missing when probe fails after enabling msix.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These cmds are issued to the fw in probe/resume and remove/suspend
paths to help fw execute some initialization and cleanup code.
This change needed the be_hw_up() code to be refactored as be_get_config().
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To send upto 64 addresses in the multicast-set cmd, the non-embeeded cmd format
that provides for a bigger buffer is used instead of an embedded format.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Sun, 2009-11-22 at 16:31 -0800, David Miller wrote:
> It should be of the form:
> if (x &&
> y)
>
> or:
> if (x && y)
>
> Fix patches, rather than complaints, for existing cases where things
> do not follow this pattern are certainly welcome.
Also collapsed some multiple tabs to single space.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following htmldocs warning:
Warning(net/core/dev.c:5378): bad line:
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx unit hang detection code in e1000e detects other hangs caused by
hardware components (e.g. Rx, DMA units), but it is not possible to detect
exactly which component is hung so it has always assumed a Tx unit hang.
When dumping a message to the system log because of a hang, this patch adds
more data to help narrow the cause of the issue and makes the message
non-Tx-specific. Because this new code reads PHY registers which can
sleep, move it off to a workqueue. This and all previously existing work
tasks in the driver are now cancelled when the driver is removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mutex_lock() calls might_sleep() the driver doesn't have to here.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A failure to initialize the identification LED is not a fatal condition and
should allow the init path to continue.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was pointed out a pm_qos DMA latency requirement set when the driver is
loaded when parts that support early receive of jumbo frames are probed
could have that requirement overidden if another part supported by the
driver (one that does not support early receive of jumbo frames) is probed
later. Change the DMA latency requirement to be per-interface if needed
instead of per driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The e1000_clear_hw_cntrs_*() functions read the registers to clear them.
There is no reason to save the register contents so the temp variable can
be removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set booleans to 'true' or 'false' to make it clear it is a boolean. Also
change instances of TRUE/FALSE in comments to lowercase true/false.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy and nvm operations structures have function pointers that contain
"phy" and "nvm" in the pointer names which are redundant since the
structures are already obviously in phy and nvm structures.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch depends on a previous one that cleans up redundant #includes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was only updating MII stats when an LSC up was detected and
the interface had not already been reported up to netdev. This meant
MII stats returned in response to an SIOCGMIIREG ioctl would always
show a link up if it had ever been up. This was misleading the networking
daemon guessnet, which uses this ioctl, into making improper network port
selections.
This fix adds a call to e1000_phy_read_status() to actively read the
mii stats before responding to the SIOCGMIIREG ioctl.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When performing the ethtool PHY loopback test on PCH-based LOMs (82577 and
82578), disable K1 (a MAC-PHY interconnect low power mode) otherwise
packets might get corrupted.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The e1000_get_cable_length_82577() should return a negative value upon
error.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Copper links with WoL or management enabled (any condition which prevents
the phy from being powered down when the interface is taken down) were
always reporting link-up when the interface had been taken down. This
is because when the interface is taken down (ifconfig ethx down),
interrupts are disabled. With no interrupts, there is no LSC interrupt,
which is normally required to set "get_link_status", which instructs the
driver to query the device for link state. The fix is to force
get_link_status to true if the interface is not up.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using legacy interrupts, do not clean the Rx ring while resetting
otherwise traffic will not pass.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide missing function pointers for ethtool set/get offloads.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clearing the interrupt timers following an IMS clear has the unwanted
side-effect of flushing all descriptors immediately following a partial
write when interrupts are disabled.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tests for 82583 in a couple ethtool functions that were missed from the
initial hardware enablement submission.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting WoL feature, check the supplied modes are all supported rather
than checking for no support. This way, if any new modes are added the
driver does not default to not complaining about it if we don't really
support it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That's extremely non-intuitive, noticed by William Allen Simpson.
And let's make the default be on, it's been suggested by a lot of
people so we'll give it a try.
Signed-off-by: David S. Miller <davem@davemloft.net>
Please apply patch to update redboot section while firmware update. Code
checks if section needs to be updated before actually doing it.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove PCI vendor and device IDs for QLE8240 and QLE8242
CNA devices. CNA devices will have separate driver.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes use of the 82580 PHY and MAC support added and adds a set
of supported device IDs for said hardware.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the 82580 MAC.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the phy included in the 82580 silicon family.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed function pointer use from non-majority address-of style
to majority short form without & via: (was: 8 with &, 36 without)
grep -rPl "\btasklet_init\s*\([^,\)]+,\s*\&" drivers/net | while read file ; do \
perl -i -e 'local $/; while (<>) { s@(\btasklet_init\s*\([^,\)]+,\s*)\&@\1@g ; print ; }' $file ;\
done
Compile tested allyesconfig x86
Signed-off-by: Joe Perches <joe@perches.com>
drivers/net/cnic.c | 4 ++--
drivers/net/jme.c | 10 +++++-----
drivers/net/skge.c | 2 +-
3 files changed, 8 insertions(+), 8 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds SIOCX25SCAUSEDIAG, allowing X.25 programs to set the cause and
diagnostic fields.
Normally used to indicate status upon closing connections.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. define macro for handling firmware api version
2. add MODULE_FIRMWARE
3. cleanup iwmct_fw_load style
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not as fancy as coccinelle. Checkpatch errors ignored.
Compile tested allyesconfig x86, not all files compiled.
grep -rPl --include=*.[ch] "\brequest_irq\s*\([^,\)]+,\s*\&" drivers/net | while read file ; do \
perl -i -e 'local $/; while (<>) { s@(\brequest_irq\s*\([^,\)]+,\s*)\&@\1@g ; print ; }' $file ;\
done
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix can probably wait 2.6.33, or should use another patch
if needed in 2.6.32 (no get_dev_by_index_rcu() before 2.6.33)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun