Add generic scancode filtering of RC input events, and fall back to
permitting any RC_FILTER_NORMAL scancode filter to be set if no s_filter
callback exists. This allows raw IR decoder events to be filtered, and
potentially allows hardware decoders to set looser filters and rely on
generic code to filter out the corner cases.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On certain motherboards (mainly Intel NUC series) bios keeps the
Nuvoton CIR device disabled at boot.
This patch adds a call to kernel PNP layer to activate the device if it
is not already activated. This will improve the chances of the PNP probe
actually succeeding on Intel NUC platforms.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DViCO FusionHDTV7 device that use au0828 can fail to communicate with
xc5000 using i2c interface because of high i2c clock speed - i2c clock
stretching bug. It causes to fail xc5000 firmware loading normally at
the current driver.
Already this problem fixed as changing to low i2c clock speed at
HVR-950q device, also DViCO FusionHDTV7 device can solve it as using low
i2c clock speed - 20KHz.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Propagate errors returned by drivers from the s_filter callback back to
userland when updating scancode filters. This allows userland to see
when the filter couldn't be updated, usually because it's not a valid
filter for the hardware.
Previously the filter was being updated conditionally on success of
s_filter, but the write always reported success back to userland.
Reported-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a device id to support for PX-S1UD (PLEX ISDB-T usb dongle) which
has sms2270.
Signed-off-by: Satoshi Nagahama <sattnag@aim.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since the introduction of the new OMAP DSS DVI connector driver in
commit 348077b154 ("OMAPDSS: Add new DVI
Connector driver"), DVI outputs report a new display type of
OMAP_DISPLAY_TYPE_DVI instead of OMAP_DISPLAY_TYPE_DPI. Handle the new
type in the IRQ handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
New board addition. No other changes.
[m.chehab@samsung.com: rebase patch and fix whitespace mangling]
Signed-off-by: Pojar George <geoubuntu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These chips makes use of the media_entity in the v4l2_subdev struct
and is therefor dependent of the MEDIA_CONTROLLER config.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
try_fmt should just set field to NONE and not return an error if
a different field was passed.
buf_prepare should check if the field passed in from userspace has a
supported field value. At the moment only NONE is supported and ANY
is mapped to NONE.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
- Set the sequence counters correctly.
- Copy timestamps, timecode, relevant buffer flags and field from
the received buffer to the outgoing buffer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
To keep the vb2 buffer administration in balance stop_streaming() must
return any pending buffers to the vb2 framework.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is no reason why we shouldn't enable this here.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This resolves an issue raised by v4l2-compliance: if the given format does
not exist, then pick a default format.
While there is an exception regarding this for TV capture drivers, this
m2m driver should do the right thing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The default of 1 second is a bit painful, switch to a 25 Hz framerate.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is no any reason to use comma here.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The adv7180 has a low power mode in which the analog and the digital processing
section are shut down. Implement the s_power callback to let bridge drivers put
the part into low power mode when not needed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for async device registration to the adv7180 driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The proper way to handle IRQs that need to be able to sleep in their IRQ handler
is to use a threaded IRQ.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The device driver core already prints out a very similar message when a driver
fails to probe. No need to print one in the driver itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The device can't possibly be registered at this point, so no need to to call
v4l2_device_unregister_subdev().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Make sure to free the control handler when the device is removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The mutex is used in the subdev callbacks, so unregister the subdev before the
mutex is destroyed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Document that it is now possible to call G/S_EDID from video nodes, not
just sub-device nodes. Add a note that -EINVAL will be returned if
the pad does not support EDIDs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Support this ioctl as part of the v4l2 core. Use the new ioctl
name and struct v4l2_edid type in the existing core code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Struct v4l2_subdev_edid and the VIDIOC_SUBDEV_G/S_EDID ioctls were
specific for subdevices, but for hardware with a simple video pipeline
you do not need/want to create subdevice nodes to just get/set the EDID.
Move the v4l2_subdev_edid struct to v4l2-common.h and rename as
v4l2_edid. Add the same ioctls to videodev2.h as well, thus allowing
this API to be used with both video nodes and v4l-subdev nodes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The wrong ioctl numbers were used due to a copy-and-paste error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.7 and up
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the driver for the LM3646, dual LED Flash driver.
The LM3646 has two 1.5A sync. boost converter with dual white current source.
It is controlled via an I2C compatible interface.
Each flash brightness, torch brightness and enable/disable can be controlled.
Under voltage, input voltage monitor and thermal threshhold Faults are added.
Please refer the datasheet http://www.ti.com/lit/ds/snvs962/snvs962.pdf
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Three Flash fault are added. V4L2_FLASH_FAULT_UNDER_VOLTAGE for the case low
voltage below the min. limit. V4L2_FLASH_FAULT_INPUT_VOLTAGE for the case
falling input voltage and chip adjust flash current not occur under voltage
event. V4L2_FLASH_FAULT_LED_OVER_TEMPERATURE for the case the temperature
exceed the maximun limit
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Descriptions for flash faults V4L2_FLASH_FAULT_UNDER_VOLTAGE,
V4L2_FLASH_FAULT_INPUT_VOLTAGE, and V4L2_FLASH_FAULT_LED_OVER_TEMPERATURE.
Removed spaces before tabs.
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If we have no pdata defined and driver fails to register we leak memory.
Converting to devm_kzalloc prevents this to happen.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Let's keep the style for all comments in the code, namely using small letters
whenever it's possible.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is no need to keep the FSF address inside each file. Moreover, it might
change in future which will make this one obsolete.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Empty port nodes are allowed but currently unsupported as the
v4l2_of_get_next_endpoint() function assumes that all port nodes have at
least an endpoint. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since I'm currently unable to dedicate sufficient time to the maintainership
of these two drivers update their status to "orphan" until new maintainers
appear.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for MBUS YUV10 BT656 and BT601 formats at rcar driver.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fixes memory leak introduced by
commit 47d8c881c3.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Set permissions on the debug module parameter to make it appear in sysfs.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This code is correct but the indenting is wrong and triggers a static
checker warning "add curly braces?".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use PCI_VENDOR_ID_INTEL instead of creating its own vendor ID #define.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The NV16M description contained some copy-and-paste text from NV12M,
suggesting that this format is a 4:2:0 format when it really is a
4:2:2 format.
Fixed the text.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
interruptible_sleep_on is racy and going away. In the arv driver that
race has probably never caused problems since it would require a whole
video frame to be captured before the read function has a chance to
go to sleep, but using wait_event_interruptible lets us kill off the
old interface. In order to do this, we have to slightly adapt the
meaning of the ar->start_capture field to distinguish between not having
started a frame and having completed it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If NO_DMA=y:
warning: (VIDEO_DM6446_CCDC && VIDEO_DM355_CCDC && VIDEO_DM365_ISIF && VIDEO_OMAP2_VOUT && VIDEO_SH_VOU && VIDEO_VIU && VIDEO_TIMBERDALE && VIDEO_MX1 && VIDEO_OMAP1) selects VIDEOBUF_DMA_CONTIG which has unmet direct dependencies (MEDIA_SUPPORT && HAS_DMA)
drivers/built-in.o: In function `videobuf_vm_close':
videobuf-dma-contig.c:(.text+0x407aa0): undefined reference to `videobuf_queue_cancel'
drivers/built-in.o: In function `__videobuf_dc_alloc':
videobuf-dma-contig.c:(.text+0x407ba2): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `__videobuf_mmap_mapper':
videobuf-dma-contig.c:(.text+0x407d44): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `free_buffer':
sh_vou.c:(.text+0x41f73a): undefined reference to `videobuf_waiton'
drivers/built-in.o: In function `sh_vou_poll':
sh_vou.c:(.text+0x41f884): undefined reference to `videobuf_poll_stream'
drivers/built-in.o: In function `sh_vou_buf_prepare':
sh_vou.c:(.text+0x41fdf6): undefined reference to `videobuf_iolock'
drivers/built-in.o: In function `sh_vou_reqbufs':
sh_vou.c:(.text+0x4203b0): undefined reference to `videobuf_reqbufs'
drivers/built-in.o: In function `sh_vou_querybuf':
sh_vou.c:(.text+0x42040a): undefined reference to `videobuf_querybuf'
drivers/built-in.o: In function `sh_vou_qbuf':
sh_vou.c:(.text+0x42045e): undefined reference to `videobuf_qbuf'
drivers/built-in.o: In function `sh_vou_dqbuf':
sh_vou.c:(.text+0x4204c2): undefined reference to `videobuf_dqbuf'
drivers/built-in.o: In function `sh_vou_streamon':
sh_vou.c:(.text+0x420572): undefined reference to `videobuf_streamon'
drivers/built-in.o: In function `sh_vou_streamoff':
sh_vou.c:(.text+0x4205d2): undefined reference to `videobuf_streamoff'
drivers/built-in.o: In function `sh_vou_mmap':
sh_vou.c:(.text+0x420c46): undefined reference to `videobuf_mmap_mapper'
VIDEO_SH_VOU selects VIDEOBUF_DMA_CONTIG, which bypasses its dependency on
HAS_DMA. Make VIDEO_SH_VOU depend on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
tree: git://linuxtv.org/media_tree.git master
head: a3550ea665
commit: a3550ea665 [499/499] [media] usbtv: split core and video implementation
reproduce: make C=1 CF=-D__CHECK_ENDIAN__
sparse warnings: (new ones prefixed by >>)
>> drivers/media/usb/usbtv/usbtv-core.c:119:22: sparse: symbol 'usbtv_id_table' was not declared. Should it be static?
>> drivers/media/usb/usbtv/usbtv-core.c:129:19: sparse: symbol 'usbtv_usb_driver' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are two troubles there:
1) the bit error measure were not accumulating;
2) it was missing the bit count.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
James Hogan