Broadwell hardware supports both ring buffer mode and execlist mode.
When i915 runs inside a VM with Intel GVT-g, we allow execlist mode
only.
The main reason of EXECLIST only is that GVT-g does not support the
dynamic mode switch between ring buffer mode and execlist mode when
running multiple virtual machines.
v2:
- Adjust the position of vgpu check in sanitize function (Joonas)
- Add vgpu error check in context initialization. (Joonas, Daniel)
Signed-off-by: Zhiyuan Lv <zhiyuan.lv@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is based on Mika Kuoppala's patch below:
http://article.gmane.org/gmane.comp.freedesktop.xorg.drivers.intel/61104/match=workaround+hw+preload
The patch will preallocate the page directories for 32-bit PPGTT when
i915 runs inside a virtual machine with Intel GVT-g. With this change,
the root pointers in EXECLIST context will always keep the same.
The change is needed for vGPU because Intel GVT-g will do page table
shadowing, and needs to track all the page table changes from guest
i915 driver. However, if guest PPGTT is modified through GPU commands
like LRI, it is not possible to trap the operations in the right time,
so it will be hard to make shadow PPGTT to work correctly.
Shadow PPGTT could be much simpler with this change. Meanwhile
hypervisor could simply prohibit any attempt of PPGTT modification
through GPU command for security.
The function gen8_preallocate_top_level_pdps() in the patch is from
Mika, with only one change to set "used_pdpes" to avoid duplicated
allocation later.
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Zhiyuan Lv <zhiyuan.lv@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a common function to return "yes" or "no" string based on the
argument, and drop the local versions of it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make it available outside of intel_dp.c.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If rc6 is enabled, notify GuC so it can do proper forcewake before
command submission.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The firmware layout changes that now it only has css header +
uCode + RSA signature. Plus, other trivial changes to support
GuC V4.3.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The driver doesn't support UMS any more, so set DRIVER_MODESET by default,
remove the legacy s/r callbacks, and rename the s/r functions to make it more clear
they're only in use by switcheroo now.
Also remove an obsolete comment about atomic. Normal updates are supported only
async updates aren't yet.
v2: Don't unconditionally set DRIVER_ATOMIC, we're not yet there.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make the code mode readable by pulling the "does this crtc have any
encoders?" deduction into a separate function.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The BIOS sometimes likes to enable pipes w/o any ports, at least on
older machines. Currently we fail to assign anything sensible to
crtc->hwmode.crtc_clock which leads to complaints from the vblank code.
Deal with active pipes w/o ports and assign something sensible to
crtc_clock in i9xx_get_pipe_config(). The encoder .get_config() will
override this if the port is enabled.
Gets rid of rest of these on my gen4:
[drm:drm_calc_timestamping_constants [drm]] *ERROR* crtc 24: Can't calculate constants, dotclock = 0!
[drm:i915_get_vblank_timestamp] crtc 1 is disabled
v2: Fill out crtc_clock already in i9xx_get_pipe_config() (Maarten)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At various points when changing the DPIO lane/phy power states,
construct an expected value of the DISPLAY_PHY_STATUS register
and compare it with the real thing.
To construct the expected value we look at our shadow PHY_CONTROL
register value (which should match what we've just written to the
hardware), and we also need to look at the actual state of the cmn
power wells as a disabled power well causes the relevant LDO status
to be reported as 'on' in DISPLAY_PHY_STATUS.
When initially powering up the PHY it performs various internal
calibrations for which it fully powers up. That means that if we check
for the expetected power state immediately upon releasing cmnreset we
would get the occasional false positive. But we can of course
poll until the expected value appears. It shouldn't be too long so
this shouldn't make modesets substantially longer.
One extra complication is introduced when we cross the streams, ie.
drive port B with pipe B. In this case we trick CL2 (where the DPLL lives)
into life by temporaily powering up the lanes in the second channel,
and once the pipe is up and runnign we release the lane power override.
At that point the power state of CL2 has somehow gotten entangled with
the power state of the first channel. That means that constructing the
expected DISPLAY_PHY_STATUS value is a bit tricky since based on the
lane power states in the second channel, CL2 should also be powered
down. But we can use the DPLL enable bit to determine when CL2 should
be alive even if the lanes are powered down. However the power state
of CL2 isn't actually tied in with the DPLL state, but to the state
of the lanes in first channel, so we have to avoid checking the
expected state between shutting down the DPLL and powering down
the lanes in the first channel. So no calling assert_chv_phy_status()
before the DISPLAY_PHY_CONTROL write in chv_phy_powergate_lanes(),
but after the write is a safe time to check.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add some checks that the state of the DPIO lanes is more or less what we
expect based on the overrides.
The hardware only provides two bits per channel indicating whether all
or some of the lanes are powered down, so we can't do an exact check.
Additionally, CL2 powering down before we can check it adds another
twist. To work around this we simply check for the 0 value of the
CL2 register (which is what we get when it's powered down) and
adjust our expectations.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we release the lane soft reset before lane stagger settings
have been programmed. I believe that means we don't actually do lane
staggering. So move the soft reset deassert to happen after lane
staggering has been programmed.
The one confusing thing in this is that when we remove the power down
override from the lanes, they power up with defaul register values,
which do not have the soft reset overrides enabled. And according to
some docs by default the data lane resets are tied to cmnreset. So that
would mean that lanes would come out of reset without staggering as
soon as the power down overrides are removed. But since we can't access
either the lane stagger register nor the soft reset override registers
until the lanes are powered on, we can't really do anything about it.
So let's just set the soft reset overrides as soon as the lane is
powered on and hope for the best.
v2: Fix typos in commit message (Daniel)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was forgotten in
commit d351f6d948
Author: Francisco Jerez <currojerez@riseup.net>
Date: Fri May 29 16:44:15 2015 +0300
drm/i915: Add SCRATCH1 and ROW_CHICKEN3 to the register whitelist.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: s/intel_dp_tps/drm_dp_tps/.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This partially reverts commit 74c090b1bd.
The DRIVER_ATOMIC cap cannot yet be exported because i915 lacks async
support.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dear git bisect user,
Even though this is the patch that introduced the WARN() you're
bisecting, please notice that it's very likely that the problem you're
facing was already present before this commit. In other words: this
commit adds code to detect errors and give WARN()s about them, but the
errors were already there.
In order to continue your debug, please use the i915.mmio_debug
option, check the backtraces and try to discover which read or write
operation is causing the error message. Then check if this is
happening because the register does not exist or because its power
well is down when the operation is being done.
On my SKL machine, if I use i915.mmio_debug=999, this patch triggers
42 WARNs just by booting. I didn't investigate them yet. Normal users
are only going to get a single WARN due to the default i915.mmio_debug
setting.
Thank you for your comprehension,
Paulo
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can choose to leave the display PHY CL2 powerdown up to some hardware
signals, or we can force it. The BXT code forces the nonexistent CL2 in
the x1 PHY to power down. Follow suit on CHV. Maybe it can still save
some extra power by disabling some extra logic in CL1, or something.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has supports some form of automagic clock gating for the
DPIO SUS clock. We can simply enable the magic bits and the
hardware should take care of the rest.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With DPIO powergating active the DPLL can't be accessed unless
something else is keeping the common lane in the channel on.
That means the PPS kick procedure could fail to enable the PLL.
Power up some data lanes to force the common lane to power up
so that the PLL can be enabled temporarily.
v2: Avoid gcc uninitilized variable warning
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Normmally the common lane in a PHY channel gets powered up when some
of the data lanes get powered up. But when we're driving port B with
pipe B we don't want to enabled any of the data lanes, and just want
the DPLL in the common lane to be active.
To make that happens we have to temporarily enable some data lanes
after which we can access the DPLL registers in the common lane. Once
the pipe is up and running we can drop the power override on the data
lanes allowing them to shut down. From this point forward the common
lane will in fact stay powered on until the data lanes in the other
channel get powered down.
Ville's extended explanation from the review thread:
On Wed, Aug 19, 2015 at 07:47:41AM +0530, Deepak wrote:
> One Q, why only for port B? Port C is also in same common lane right?
Port B is in the first PHY channel which also houses CL1. CL1 always
powers up whenever any lanes in either PHY channel are powered up.
CL2 only powers up if lanes in the second channel (ie. the one with
port C) powers up.
So in this scenario (pipe B->port B) we want the DPLL from CL2, but
ideally we only want to power up the lanes for port B. Powering up
port B lanes will only power up CL1, but as we need CL2 instead we
need to, temporarily, power up some lanes in port C as well.
Crossing the streams the other way (pipe A->port C) is not a problem
since CL1 powers up whenever anything else powers up. So powering up
some port C lanes is enough on its own to make the CL1 DPLL
operational, even though CL1 and the lanes live in separate channels.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
[danvet: Amend commit message with extended explanation.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Powergate the PHY lanes when they're not needed. For HDMI all four lanes
are needed always, but for DP we can enable only the needed lanes. To
power down the unused lanes we use some power down override bits in the
DISPLAY_PHY_CONTROL register. Without the overrides it appears that the
hardware always powers on all the lanes. When the port is disabled the
power down override is not needed and the lanes will shut off on their
own. That also means the override is critical to actually be able to
access the DPIO registers before the port is actually enabled.
Additionally the common lanes will power down when not needed. CL1
remains on as long as anything else is on, CL2 will shut down when
all the lanes in the same channel will shut down. There is one exception
for CL2 that will be dealt in a separate patch for clarity.
With potentially some lanes powered down, the DP code now has to check
the number of active lanes before accessing PCS/TX registers. All
registers in powered down blocks will reads as 0xffffffff, and soe we
would drown in warnings from vlv_dpio_read() if we allowed the code
to access all those registers.
Another important detail in the DP code is the "TX latency optimal"
setting. Normally the second TX lane acts as some kind of reset master,
with the other lanes as slaves. But when only a single lane is enabled,
that single lane obviously has to be the master.
A bit of extra care is needed to reconstruct the initial state of the
DISPLAY_PHY_CONTROL register since it can't be read safely. So instead
read the actual lane status from the DPLL/PHY_STATUS registers and
use that to determine which lanes ought to be powergated initially.
We also need to switch the PHY power modes to "deep PSR" to avoid
a hard system hang when powering down the single channel PHY.
Also sprinkle a few debug prints around so that we can monitor the
DISPLAY_PHY_STATUS changes without having to read it and risk
corrupting it.
v2: Add locking to chv_powergate_phy_lanes()
v3: Actually enable dynamic powerdown in the PHY and deal with the
fallout
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bunch of stuff needs the DPLL ref/cri clocks on both VLV and CHV,
and having VGA mode enabled causes some problems for CHV. So let's just
pull the code to configure those bits into the disp2d well enable hook.
With the DPLL disable code also fixed to leave those bits alone we
should now have a consistent DPLL state all the time even if the DPLL
is disabled.
This also neatly removes some duplicated code between the VLV and
CHV codepaths.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Most of our char* arrays are markes as const already, but a few slipped
through the cracks. Fix it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A couple of hand rolled ARRAY_SIZE()s caught my eye. Get rid of them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Simple one:
drivers/gpu/drm/i915/i915_debugfs.c:2449:57: warning: Using plain integer as NULL pointer
And something a bit more peculiar:
drivers/gpu/drm/i915/i915_debugfs.c:4953:18: warning: Variable length array is used.
drivers/gpu/drm/i915/i915_debugfs.c:4953:32: warning: Variable length array is used.
We pass a 'const int' as the array size which results in the warning,
dropping the const gets rid of the warning. Weird, but I think getting
rid of the warnings is better than holding on to the const.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BXT platform uses live status bits from 0x44440 register to obtain DP
status on hotplug. The existing g4x_digital_port_connected() uses a
different register and hence misses DP hotplug events on BXT
platform. This patch fixes it by using the appropriate register(0x44440)
and live status bits(3:5).
Based on a patch by Durgadoss R <durgadoss.r@intel.com>, from whom the
commit message is shamelessly copy pasted.
Reported-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Choose the right function at the intel_digital_port_connected level.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Choose the right function at the intel_digital_port_connected level.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a common intel_digital_port_connected() that splits out to functions
for different platforms. No functional changes.
v2: make the function return a boolean
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the case added for eDP on port A (always connected from this
function's point of view), we should not be hitting any of the default
cases in ibx_digital_port_connected, so add MISSING_CASE annotation.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should not be hitting any of the default cases in
g4x_digital_port_connected, so add MISSING_CASE annotation and return
boolean status. The current behaviour is just cargo culting from the
days of yonder when the display port support was added to i915.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The function can be made static there. No functional changes.
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is possible the we request to have a mode that has
higher pixel clock than our HW can support. This patch
checks if requested pixel clock is lower than the one
supported by the HW. The requested mode is discarded
if we cannot support the requested pixel clock.
This patch applies to DVO.
V2:
- removed computation for max pixel clock
V3:
- cleanup by removing unnecessary lines
V4:
- clock check against max dotclock moved inside 'if (fixed_mode)'
V5:
- dot clock check against fixed_mode clock when available
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is possible the we request to have a mode that has
higher pixel clock than our HW can support. This patch
checks if requested pixel clock is lower than the one
supported by the HW. The requested mode is discarded
if we cannot support the requested pixel clock.
This patch applies to DSI.
V2:
- removed computation for max pixel clock
V3:
- cleanup by removing unnecessary lines
V4:
- max_pixclk variable renamed as max_dotclk
- moved dot clock checking inside 'if (fixed_mode)'
V5:
- dot clock checked against fixed_mode clock
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is possible the we request to have a mode that has
higher pixel clock than our HW can support. This patch
checks if requested pixel clock is lower than the one
supported by the HW. The requested mode is discarded
if we cannot support the requested pixel clock.
This patch applies to LVDS.
V2:
- removed computation for max pixel clock
V3:
- cleanup by removing unnecessary lines
V4:
- moved supported dotclock check from mode_valid() to intel_lvds_init()
V5:
- dotclock check moved back to mode_valid() function
- dotclock check for fixed mode
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Store max dotclock into dev_priv structure so we are able
to filter out the modes that are not supported by our
platforms.
V2:
- limit the max dot clock frequency to max CD clock frequency
for the gen9 and above
- limit the max dot clock frequency to 90% of the max CD clock
frequency for the older gens
- for Cherryview the max dot clock frequency is limited to 95%
of the max CD clock frequency
- for gen2 and gen3 the max dot clock limit is set to 90% of the
2X max CD clock frequency
V3:
- max_dotclk variable renamed as max_dotclk_freq in i915_drv.h
- in intel_compute_max_dotclk() the rounding method changed from
round up to round down when computing max dotclock
V4:
- Haswell and Broadwell supports now dot clocks up to max CD clock
frequency
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add vlv_dport_to_phy() and fix up the return values of
vlv_dport_to_channel() and vlv_pipe_to_channel() to use
the appropriate enums.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With DPIO powergating active on CHV, we can't even access the DPIO PLL
registers until the lane power state overrides have been enabled. That
will happen from the encoder .pre_pll_enable() hook, so move
chv_prepare_pll() to happen after that point, which puts it just before
chv_enable_pll() actually.
Do the same for VLV to avoid accumulating weird differences between the
platforms. Both platforms seem happy with the new arrangement.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
dev_priv->chv_phy_control is protected by the power_domains->lock
elsewhere, so also grab it when initializing chv_phy_control.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To implement DPIO lane power gating on CHV we're going to need to access
DPIO registers from the cmn power well enable hook. That gets called
rather early, so we need to move the DPIO port IOSF sideband port
assignment earlier as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the CHV clock buffer disable from chv_disable_pll() to the new
encoder .post_pll_disable() hook. This is more symmetric since the
clock buffer enable happens from the .pre_pll_enable() hook.
We'll have more use for the new hook soon.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The docs give you the impression that the unique transition scale
value shouldn't matter when unique transition scale is enabled. But
as Imre found on BXT (and I verfied also on BSW) the value does
matter. So from now on just program the same value 0x9a always.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When fractional m2 divider isn't used on CHV the fractional part
is ignore by the hardware. Despite that, program the fractional
value (0 in this case) to the hardware register just to keep
things a bit more consistent. Might at least make register dumps
a bit less confusing when there isn't some stale fractional part
hanging around.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current versions of these two macros don't work correctly if the
argument expression happens to contain a modulo operator (%) -- when
stringified, it gets interpreted as a printf formatting character!
With a specifically crafted parameter, this could probably cause a
kernel OOPS; consider WARN_ON(p%s) or WARN_ON(f %*pEp).
Instead, we should use an explicit "%s" format, with the stringified
expression as the coresponding literal-string argument.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With MST there won't be a crtc assigned to the main link encoder, so
trying to dig up the pipe_config from there is a recipe for an oops.
Instead store the parameters (lane_count and link_rate) in the encoder,
and use those values during link training etc. Since those parameters
are now assigned only when the link is actually enabled,
.compute_config() won't clobber them as it did before.
Hardware state readout is still bonkers though as we don't transfer the
link parameters from pipe_config intel_dp. We should do that during
encoder sanitation. But since we don't even do a proper job of reading
out the main link encoder state for MST there's littel point in
worrying about this now.
Fixes a regression with MST caused by:
commit 90a6b7b052
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Jul 6 16:39:15 2015 +0300
drm/i915: Move intel_dp->lane_count into pipe_config
v2: Different apporoach that should keep intel_dp_check_mst_status()
somewhat less oopsy
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Due to a coherency issue on BXT A steppings we can't guarantee a
coherent view of cached (CPU snooped) GPU mappings, so fail such
requests. User space is supposed to fall back to uncached mappings in
this case.
v2:
- limit the WA to A steppings, on later stepping this HW issue is fixed
v3:
- return error instead of trying to work around the issue in kernel,
since that could confuse user space (Chris)
Testcast: igt/gem_store_dword_batches_loop/cached-mapping
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By running igt/store_dword_loop_render on BXT we can hit a coherency
problem where the seqno written at GPU command completion time is not
seen by the CPU. This results in __i915_wait_request seeing the stale
seqno and not completing the request (not considering the lost
interrupt/GPU reset mechanism). I also verified that this isn't a case
of a lost interrupt, or that the command didn't complete somehow: when
the coherency issue occured I read the seqno via an uncached GTT mapping
too. While the cached version of the seqno still showed the stale value
the one read via the uncached mapping was the correct one.
Work around this issue by clflushing the corresponding CPU cacheline
following any store of the seqno and preceding any reading of it. When
reading it do this only when the caller expects a coherent view.
v2:
- fix using the proper logical && instead of a bitwise & (Jani, Mika)
- limit the workaround to A stepping, on later steppings this HW issue
is fixed
v3:
- use a separate get_seqno/set_seqno vfunc (Chris)
Testcase: igt/store_dword_loop_render
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We also need to call the frontbuffer flip to trigger proper
invalidations when disabling planes. Otherwise we will miss
screen updates when disabling sprites or cursor.
On core platforms where HW tracking also works, this issue
is totally masked because HW tracking triggers PSR exit
however on VLV/CHV that has only SW tracking we miss screen
updates when disabling planes.
It was caught with kms_psr_sink_crc sprite_plane_onoff
and cursor_plane_onoff subtests running on VLV/CHV.
This is probably a regression since I can also get this
with the manual test case, but with so many changes on atomic
modeset I couldn't track exactly when this was introduced.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Zhiyuan Lv