Allow injected unicast frames to be sent without having to wait
for an ACK.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes compilation errors when compiling for ARM:
ath6kl/debug.c:312: error: implicit declaration of function 'vmalloc'
ath6kl/debug.c:312: warning: assignment makes pointer from integer without a cast
ath6kl/debug.c:342: error: implicit declaration of function 'vfree'
ath6kl/debug.c:696: warning: assignment makes pointer from integer without a cast
ath6kl/debug.c:871: warning: assignment makes pointer from integer without a cast
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
My earlier debug log additions added these warnings when compiling 64 bit
kernels:
ath6kl/init.c:962: warning: format '%d' expects type 'int',
but argument 3 has type 'size_t'
ath6kl/init.c:975: warning: format '%d' expects type 'int',
but argument 3 has type 'size_t'
ath6kl/init.c:988: warning: format '%d' expects type 'int',
but argument 3 has type 'size_t'
ath6kl/init.c:1009: warning: format '%d' expects type 'int',
but argument 3 has type 'size_t'
ath6kl/init.c:1192: warning: format '%d' expects type 'int',
but argument 4 has type 'size_t'
ath6kl/init.c:1236: warning: format '%d' expects type 'int',
but argument 4 has type 'size_t'
ath6kl/init.c:1267: warning: format '%d' expects type 'int',
but argument 4 has type 'size_t'
Reported-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
802.11 says:
"Sequence numbers for QoS (+)Null frames may be
set to any value."
However, if we use the normal counters then peers
will get confused with aggregation since there'll
be holes in the sequence number sequence.
To avoid that, neither assign a sequence number
to QoS null frames nor put them on aggregation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the addition of uAPSD and driver buffering
the powersave handling has gotten quite complex.
Add a section to the documentation to explain it
for anyone wanting to implement it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi has a separate EOSP notification from
the device, and to make use of that properly
it needs to be passed to mac80211. To be able
to mix with tx_status_irqsafe and rx_irqsafe
it also needs to be an "_irqsafe" version in
the sense that it goes through the tasklet,
the actual flag clearing would be IRQ-safe
but doing it directly would cause reordering
issues.
This is needed in the case of a P2P GO going
into an absence period without transmitting
any frames that should be driver-released as
in this case there's no other way to inform
mac80211 that the service period ended. Note
that for drivers that don't use the _irqsafe
functions another version of this function
will be required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi needs to know the number of frames that are
going to be sent to a station while it is asleep so
it can properly handle the uCode blocking of that
station.
Before uAPSD, we got by by telling the device that
a single frame was going to be released whenever we
encountered IEEE80211_TX_CTL_POLL_RESPONSE. With
uAPSD, however, that is no longer possible since
there could be more than a single frame.
To support this model, add a new callback to notify
drivers when frames are going to be released.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My work and some previous work didn't add
all the flags, add them now and while at it
simplify the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flaglock in struct sta_info has long been
something that I wanted to get rid of, this
finally does the conversion to atomic bitops.
The conversion itself is straight-forward in
most places, a few things needed to change a
bit since we can no longer use multiple bits
at the same time.
On x86-64, this is a fairly significant code
size reduction:
text data bss dec hex
427861 23648 1008 452517 6e7a5 before
425383 23648 976 450007 6ddd7 after
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a PS-poll frame is retried (but was received)
there is no way to detect that since it has no
sequence number. As a consequence, the standard
asks us to not react to PS-poll frames until the
response to one made it out (was ACKed or lost).
Implement this by using the WLAN_STA_SP flags to
also indicate a PS-Poll "service period" and the
IEEE80211_TX_STATUS_EOSP flag for the response
packet to indicate the end of the "SP" as usual.
We could use separate flags, but that will most
likely completely confuse drivers, and while the
standard doesn't exclude simultaneously polling
using uAPSD and PS-Poll, doing that seems quite
problematic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For PS-poll, there's a possible race between
us expiring a frame and the station polling
for it -- send it a null frame in that case.
For uAPSD, the standard says that we have to
send a frame in each SP, so send null if we
don't have any other frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add uAPSD support to mac80211. This is probably not
possible with all devices, so advertising it with
the cfg80211 flag will be left up to drivers that
want it.
Due to my previous patches it is now a fairly
straight-forward extension. Drivers need to have
accurate TX status reporting for the EOSP frame.
For drivers that buffer themselves, the provided
APIs allow releasing the right number of frames,
but then drivers need to set EOSP and more-data
themselves. This is documented in more detail in
the new code itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there are frames for a station buffered in
the driver, mac80211 announces those in the TIM
IE but there's no way to release them. Add new
API to release such frames and use it when the
station polls for a frame.
Since the API will soon also be used for uAPSD
it is easily extensible.
Note that before this change drivers announcing
driver-buffered frames in the TIM bit actually
will respond to a PS-Poll with a potentially
lower priority frame (if there are any frames
buffered in mac80211), after this patch a driver
that hasn't been changed will no longer respond
at all. This only affects ath9k, which will need
to be fixed to implement the new API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It doesn't seem likely, but maybe possible, that the
more-data bit needs to be recomputed due to changes
in the queued frames. Clear it for filtered frames
to ensure that we never send it incorrectly. It'll
be set again as necessary when we retransmit this
frame.
The more likely case is maybe where the station woke
up after the filtered frame in which case more-data
should be clear when the frame is transmitted to the
station since it is now awake.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we no longer use the return value, we no
longer need to maintain it either, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For uAPSD support we'll need to have per-AC PS
buffers. As this is a major undertaking, split
the buffers before really adding support for
uAPSD. This already makes some reference to the
uapsd_queues variable, but for now that will
never be non-zero.
Since book-keeping is complicated, also change
the logic for keeping a maximum of frames only
and allow 64 frames per AC (up from 128 for a
station).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 will expire normal PS-buffered frames, but
if the device rejected some frames for a sleeping
station, these won't be on the ps_tx_buf queue but
on the tx_filtered queue instead; this is done to
avoid reordering.
However, mac80211 will not expire frames from the
filtered queue, let's fix that.
Also add a more comments to what all this expiry is
doing and how it works.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the TIM bit for a given station is set
and cleared all over the place. Since the logic to
set/clear it will become much more complex when we
add uAPSD support, as a first step let's collect
the entire logic in one place. This requires a few
small adjustments to other places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For uAPSD implementation, it is necessary to know on
which ACs frames are buffered. mac80211 obviously
knows about the frames it has buffered itself, but
with aggregation many drivers buffer frames. Thus,
mac80211 needs to be informed about this.
For now, since we don't have APSD in any form, this
will unconditionally set the TIM bit for the station
but later with uAPSD only some ACs might cause the
TIM bit to be set.
ath9k is the only driver using this API and I only
modify it in the most basic way, it won't be able
to implement uAPSD with this yet. But it can't do
that anyway since there's no way to selectively
release frames to the peer yet.
Since drivers will buffer frames per TID, let them
inform mac80211 on a per TID basis, mac80211 will
then sort out the AC mapping itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark the STA entries of enabled TDLS peers with a new "peer authorized"
flag.
During link setup, allow special TDLS setup frames through the AP, but
otherwise drop all packets destined to the peer. This is required by the
TDLS (802.11z) specification in order to prevent reordering of MSDUs
between the AP and direct paths.
When setup completes and the peer is authorized, send data directly,
bypassing the AP.
In the Rx path, allow data to be received directly from TDLS peers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When adding a TDLS peer STA, mark it with a new flag in both nl80211 and
mac80211. Before adding a peer, make sure the wiphy supports TDLS and
our operating mode is appropriate (managed).
In addition, make sure all peers are removed on disassociation.
A TDLS peer is first added just before link setup is initiated. In later
setup stages we have more info about peer supported rates, capabilities,
etc. This info is reported via nl80211_set_station().
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Register and implement the TDLS cfg80211 callback functions.
Internally prepare and send TDLS management frames. We incorporate
local STA capabilities and supported rates with extra IEs given by
usermode. The resulting packet is either encapsulated in a data frame,
or assembled as an action frame. It is transmitted either directly or
through the AP, as mandated by the TDLS specification.
Declare support for the TDLS external setup wiphy capability. This
tells usermode to handle link setup and discovery on its own, and use the
kernel driver for sending TDLS mgmt packets.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Relocate the mesh implementation of adding the (extended) supported
rates IE to util.c, anticipating its use by other parts of mac80211.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for sending high-level TDLS commands and TDLS frames via
NL80211_CMD_TDLS_OPER and NL80211_CMD_TDLS_MGMT, respectively. Add
appropriate cfg80211 callbacks for lower level drivers.
Add wiphy capability flags for TDLS support and advertise them via
nl80211.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
both sta and lq_sta are guaranteed to be not null in the
calling function so we don't need to check them here.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_gpio_get reads the GPIO in/out registers to get the status of
GPIO pins, so use PS wrappers
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when hostapd sets the station as authorized
we also overwrite its uAPSD parameter. This obviously
leads to buggy behaviour (later, with my patches that
actually add uAPSD support). To fix this, only apply
those parameters if they were actually set in nl80211,
and to achieve that add a bitmap of things to apply.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Making adding and deleting virtual interfaces dynamic. Adding
handlers for creating and deleting virtual interface with
given name and dev respectively.
Also, creating default interface of type station on insmod of
the driver.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"iw dev mlan0 link" shows wrong data rate, because data rate is
not sent properly to cfg80211 stack. Also stack is not updated
with mcs and Tx data flags information.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In disconnected state "iw dev mlan0 link" command will return
from cfg80211 stack itself. We also have an error check in
mwifiex_cfg80211_get_station() routine. Therefore the code
under "if (!priv->media_connected)" condition in
mwifiex_rate_ioctl_get_rate_value() routine becomes unreachable.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An extra call to mwifiex_dump_station_info() routine in get_station
callback function is redundant
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of the rx status's is_mybeacon in order to avoid
redundant memcmp.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fill the ampdu_[ack]_len for both aggregation and normal frames.
So that we could avoid unnecesary conditional at tx status.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed a possible issue in the max_tp_rate2 management of
minstrel_ht. In particular, if we look up just among max_tp_rate2 of
each group it will be possible that the selected rate will not be the
mcs with second maximum throughput. I wrote this simple patch.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otheriwse the module.h split up fails like this:
drivers/net/wireless/ath/ath6kl/init.c:27:26: error: expected ')' before 'uint'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For some reason firmware is sending invalid rates when we try to
query current bitrate from ath6kl_get_station() and a warning is issued:
[ 3810.415720] ath6kl: invalid rate: 1935633515
[ 3811.105493] ath6kl: invalid rate: 1935633515
[ 3811.556063] ath6kl: invalid rate: 1935633515
As the warning happens way too often, convert the warning to a debug
message once we have a proper fix. But to make it easy to follow
how often the problem appears, add a debugfs to print
various statistics about workarounds and make this issue the first WAR.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Correct flag usage - use it as a bit index instead of a bit value.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wrqu->encoding.length comes from the network administrator. It's
size u16. We want to limit "tocopy" to the smallest value of either
"len_keys", "wrqu->encoding.length" or 100. But because .length
gets cast from u16 to u8 we might use a random, smaller value than
the was desired. It's probably not very serious, but we may as well
fix it.
Btw, this is from code auditing and not from testing. I don't know
if this affects anyone in real life.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
save and configure tx param per sdata, rather than
per hardware.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx params are currently configured per hw, although they
should be configured per interface.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever the scan request or tx_mgmt is requesting not to
use CCK rate for managemet frames through
NL80211_ATTR_TX_NO_CCK_RATE attribute, then mac80211 should
select appropriate least non-CCK rate. This could help to
send P2P probes and P2P action frames at non 11b rates
without diabling 11b rates globally.
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa