Using a static variable for counting the number of CCWs attached to
a DMA channel when appending a new descriptor is not multi user safe.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
There is no need to have the clock enabled all the time the driver is
loaded.
It will be enabled anyway in mxs_dma_alloc_chan_resources() when a
channel is actually going to be used.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
amba_probe() now calls pm_runtime_get_noresume() and pm_runtime_enable()
for the devices before the device probe is called. Hence we don't need
to call pm_runtime_get_xxx and pm_runtime_enable() in device probe again.
In the same way, since amba_remove() calls the respective pm_runtime
functions, those functions need not be called from device remove.
This patch fixes following run time error with pl330 driver.
dma-pl330 dma-pl330.0: Unbalanced pm_runtime_enable!
dma-pl330 dma-pl330.0: failed to get runtime pm
Signed-off-by: Giridhar Maruthy <giridhar.maruthy@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The IPU internally works on 32bit colors. It can arbitrarily map
between pixel formats and internal representation and also between
internal representation and the physical connection to the display.
The driver used to change the mapping between internal representation
and display connection depending on the user selected bpp which is
wrong. Instead, the mapping is specified by the hardware, so an
additional field in platform data is added to describe the connection
between i.MX and the display. The default for this field is RGB666
which seems to be the only configuration which works without this
patch, so I assumed that all in Kernel boards are connected this
way.
This patch has been tested on a RGB666 connected display and a
RGB888 connected display in both 16bpp and 32bpp modes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The burstsize (npb in struct chan_param_mem) is set in
ipu_ch_param_set_size() once. The number of allowed
pixels in a burst depend on the pixel format and the
rotation mode. For 16bit formats 16 pixels are allowed
whereas for 32bit formats only 8 pixels are allowed.
Set these values correctly in ipu_ch_param_set_size()
and do not overwrite them afterwards.
We do not support rotation right now, so ignore this
case.
This patch fixes the wrong burstsize setting of 16 pixels
for 32bpp.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Allow logical channels to specify the physical channel they want to use.
This is needed to avoid two peripherals operating on the same physical
channel during some special use-cases. (like mmc and usb during a
usb mass storage case).
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Narayanan G <narayanan.gopalakrishnan@stericsson.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Currently, if plchan->phychan is true, we return immediately from
prep_phy_chan(). We must configure txd->ccfg and increment phychan_hold before
returning. Otherwise, request line number wouldn't be configured in this txd.
Reported-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This patch converts the drivers in drivers/dma/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Piotr Ziecik <kosmo@semihalf.com>
Cc: Rongjun Ying <rongjun.ying@csr.com>
Cc: Barry Song <21cnbao@gmail.com>
Cc: Pelagicore AB <info@pelagicore.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
When we use the SDMA in the UART driver(such as imx6q), we will
meet one situation:
Assume we set 64 bytes for the RX DMA buffer.
The RX DMA buffer has received some data, but not full.
An Aging DMA request will be received by the SDMA controller if we enable the
IDDMAEN(UCR4[6]) in this case.
So the UART driver needs to know the count of the real received bytes,
and push them to upper layer.
Add two new fields to sdmac, and update the `residue` in sdma_tx_status().
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Setting the flags in case of IDE didn't have any effect since the control
register is overwritten few lines below. So move these to be after the control
register is initialized.
Signed-off-by: Rafal Prylowski <prylowski@metasoft.pl>
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Using a configuration structure simplify the finding of SoC
dependent parameters. Both platform data and device tree ids are
using these structures.
This will separate data from code and remove the need for an enum.
Idea from Grant Likely.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Trivial form modification to unify structure look.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This patch provides an option of having the lcla (link address)
in ESRAM instead of allocating it. The bool value (use_esram_lcla)
in the stedma40_platform_data if set to true, then the lcla
address would be taken from platform resources. Also, the
corresponding esram regulator is managed in the
suspend/resume functions.
Signed-off-by: Narayanan G <narayanan.gopalakrishnan@stericsson.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Sparse warns:
drivers/dma/timb_dma.c:168:17: warning: mixing different enum types
drivers/dma/timb_dma.c:168:17: int enum dma_transfer_direction versus
drivers/dma/timb_dma.c:168:17: int enum dma_data_direction
drivers/dma/timb_dma.c:172:32: warning: mixing different enum types
drivers/dma/timb_dma.c:172:32: int enum dma_transfer_direction versus
drivers/dma/timb_dma.c:172:32: int enum dma_data_direction
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
In S2R all DMA registers are reset by hardware and thus they are required to be
reprogrammed. The channels which aren't reprogrammed are channel configuration
and interrupt enable registers, which are currently programmed at chan_alloc
time.
This patch creates another routine to initialize a channel. It will try to
initialize channel on every dwc_dostart() call. If channel is already
initialised then it simply returns, otherwise it configures registers.
This routine will also initialize registers on wakeup from S2R, as we mark
channels as uninitialized on suspend.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Set the right DMA direction in the sdma_control(), else
we will get the wrong log when enable the DYNAMIC_DEBUG.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This patch adds power management support to the dma40
driver. The DMA registers are backed up and restored,
during suspend/resume. Also flags to track the dma usage
have been introduced to facilitate this. Patch also includes
few other minor changes, related to formatting, comments.
Signed-off-by: Narayanan G <narayanan.gopalakrishnan@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
[fixed direction enums and cyclic api based on changes
already merged]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Define a new api that could be used for doing fancy data transfers
like interleaved to contiguous copy and vice-versa.
Traditional SG_list based transfers tend to be very inefficient in
such cases as where the interleave and chunk are only a few bytes,
which call for a very condensed api to convey pattern of the transfer.
This api supports all 4 variants of scatter-gather and contiguous transfer.
Of course, neither can this api help transfers that don't lend to DMA by
nature, i.e, scattered tiny read/writes with no periodic pattern.
Also since now we support SLAVE channels that might not provide
device_prep_slave_sg callback but device_prep_interleaved_dma,
remove the BUG_ON check.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Acked-by: Barry Song <Baohua.Song@csr.com>
[renamed dmaxfer_template to dma_interleaved_template
did fixup after the enum dma_transfer_merge]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
fixup usage of dma direction by introducing dma_transfer_direction,
this patch moves usb/renesas driver to use new enum
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
fixup usage of dma direction by introducing dma_transfer_direction,
this patch moves usb/musb driver to use new enum
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
On October 1 in 2011,
OKI SEMICONDUCTOR Co., Ltd. changed the company name in to LAPIS Semiconductor
Co., Ltd.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The individual SoC dependency in Kconfig hardly scales anymore.
Instead of having such a fine grained dependency just depend
on ARCH_MXC and risk that the uninformed user has to look in
the help text to figure out which driver is the correct one.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This patch adds to fix the build warning as following.
drivers/dma/pl330.c: In function 'pl330_probe':
drivers/dma/pl330.c:859: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Add device tree probe support for atmel at_hdmac DMA driver.
Bindings are added to specify DMA controller configuration.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
We remove the use of platform data from DMA controller driver.
We now use of .id_table to distinguish between compatible
types. The two implementations allow to determine the
number of channels and the capabilities of the controller.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
.. with new name. Because nothing says "really solid kernel release"
like naming it after an extinct animal that just happened to be in the
news lately.
Mountpoint crossing is similar to following procfs symlinks - we do
not get ->d_revalidate() called for dentry we have arrived at, with
unpleasant consequences for NFS4.
Simple way to reproduce the problem in mainline:
cat >/tmp/a.c <<'EOF'
#include <unistd.h>
#include <fcntl.h>
#include <stdio.h>
main()
{
struct flock fl = {.l_type = F_RDLCK, .l_whence = SEEK_SET, .l_len = 1};
if (fcntl(0, F_SETLK, &fl))
perror("setlk");
}
EOF
cc /tmp/a.c -o /tmp/test
then on nfs4:
mount --bind file1 file2
/tmp/test < file1 # ok
/tmp/test < file2 # spews "setlk: No locks available"...
What happens is the missing call of ->d_revalidate() after mountpoint
crossing and that's where NFS4 would issue OPEN request to server.
The fix is simple - treat mountpoint crossing the same way we deal with
following procfs-style symlinks. I.e. set LOOKUP_JUMPED...
Cc: stable@kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf top: Fix live annotation in the --stdio interface
perf top tui: Don't recalc column widths considering just the first page
perf report: Add progress bar when processing time ordered events
perf hists browser: Warn about lost events
perf tools: Fix a typo of command name as trace-cmd
perf hists: Fix recalculation of total_period when sorting entries
perf header: Fix build on old systems
perf ui browser: Handle K_RESIZE in dialog windows
perf ui browser: No need to switch char sets that often
perf hists browser: Use K_TIMER
perf ui: Rename ui__warning_paranoid to ui__error_paranoid
perf ui: Reimplement the popup windows using libslang
perf ui: Reimplement ui__popup_menu using ui__browser
perf ui: Reimplement ui_helpline using libslang
perf ui: Improve handling sigwinch a bit
perf ui progress: Reimplement using slang
perf evlist: Fix grouping of multiple events
Commit 32aaeffbd4 (Merge branch
'modsplit-Oct31_2011'...) caused some build errors. Fix these
and make sure we always have export.h or module.h included
for MODULE_ and EXPORT_SYMBOL users:
$ grep -rl ^MODULE_ arch/arm/*omap*/*.c | xargs \
grep -L linux/module.h
arch/arm/mach-omap2/dsp.c
arch/arm/mach-omap2/mailbox.c
arch/arm/mach-omap2/omap-iommu.c
arch/arm/mach-omap2/smartreflex.c
Also check we either have export.h or module.h included
for the files exporting symbols:
$ grep -rl EXPORT_SYMBOL arch/arm/*omap*/*.c | xargs \
grep -L linux/export.h | xargs grep -L linux/module.h
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Include linux/export.h to fix below build warning:
CC arch/arm/plat-omap/omap_device.o
arch/arm/plat-omap/omap_device.c:1055: warning: data definition has no type or storage class
arch/arm/plat-omap/omap_device.c:1055: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
arch/arm/plat-omap/omap_device.c:1055: warning: parameter names (without types) in function declaration
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
forcedeth: fix a few sparse warnings (variable shadowing)
forcedeth: Improve stats counters
forcedeth: remove unneeded stats updates
forcedeth: Acknowledge only interrupts that are being processed
forcedeth: fix race when unloading module
MAINTAINERS/rds: update maintainer
wanrouter: Remove kernel_lock annotations
usbnet: fix oops in usbnet_start_xmit
ixgbe: Fix compile for kernel without CONFIG_PCI_IOV defined
etherh: Add MAINTAINERS entry for etherh
bonding: comparing a u8 with -1 is always false
sky2: fix regression on Yukon Optima
netlink: clarify attribute length check documentation
netlink: validate NLA_MSECS length
i825xx:xscale:8390:freescale: Fix Kconfig dependancies
macvlan: receive multicast with local address
tg3: Update version to 3.121
tg3: Eliminate timer race with reset_task
tg3: Schedule at most one tg3_reset_task run
tg3: Obtain PCI function number from device
...
This fixes the following sparse warnings:
drivers/net/ethernet/nvidia/forcedeth.c:2113:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2102:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2155:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2102:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2227:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2215:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2271:7: warning: symbol 'size' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2215:6: originally declared here
drivers/net/ethernet/nvidia/forcedeth.c:2986:20: warning: symbol 'addr' shadows an earlier one
drivers/net/ethernet/nvidia/forcedeth.c:2963:6: originally declared here
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx byte count was off; instead use the hardware's count. Tx packet
count was counting pre-TSO packets; instead count on-the-wire packets.
Report hardware dropped frame count as rx_fifo_errors.
- The count of transmitted packets reported by the forcedeth driver
reports pre-TSO (TCP Segmentation Offload) packet counts and not the
count of the number of packets sent on the wire. This change fixes
the forcedeth driver to report the correct count. Fixed the code by
copying the count stored in the NIC H/W to the value reported by the
driver.
- Count rx_drop_frame errors as rx_fifo_errors:
We see a lot of rx_drop_frame errors if we disable the rx bottom-halves
for too long. Normally, rx_fifo_errors would be counted in this case.
The rx_drop_frame error count is private to forcedeth and is not
reported by ifconfig or sysfs. The rx_fifo_errors count is currently
unused in the forcedeth driver. It is reported by ifconfig as overruns.
This change reports rx_drop_frame errors as rx_fifo_errors.
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function ndo_get_stats() updates most of the stats from hardware
registers, making the manual updates un-needed. This change removes
these manual updates. Main exception is rx_missed_errors which needs
manual update.
Another exception is rx_packets, still updated manually in this commit
to make sure this patch doesn't change behavior of driver. This will
be addressed by a future patch.
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to avoid a race, accidentally acknowledging an interrupt that
we didn't notice and won't immediately process. This is based solely
on code inspection; it is not known if there was an actual bug here.
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When forcedeth module is unloaded, there exists a path that can lead
to mod_timer() after del_timer_sync(), causing an oops. This patch
short-circuits this unneeded path, which originates in
nv_get_ethtool_stats().
Tested:
x86_64 16-way + 3 ethtool -S infinite loops + 100Mbps incoming traffic
+ rmmod/modprobe/ifconfig in a loop
Initial-Author: Salman Qazi <sqazi@google.com>
Discussion: http://patchwork.ozlabs.org/patch/123548/
Signed-off-by: David Decotigny <david.decotigny@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
since it uses the module facilities.
Reported-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the files which are not themselves modular, we can change
them to include only the smaller export.h since all they are
doing is looking for EXPORT_SYMBOL.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These files didn't exist at the time of the module.h split, and
so were not fixed by the commits on that baseline. Since they use
the EXPORT_SYMBOL and/or THIS_MODULE macros, they will need the
new export.h file included that provides them.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lothar Waßmann