The maximum receive packet size field in the Port Serial Control
register controls at what size received packets are flagged
overlength in the receive descriptor, but it doesn't prevent
overlength packets from being DMAd to memory and signaled to the
host like other received packets.
mv643xx_eth does not support receiving jumbo frames in 10/100 mode,
but setting the packet threshold to larger than 1522 bytes in 10/100
mode won't cause breakage by itself.
If we really want to enforce maximum packet size on the receiving
end instead of on the sending end where it should be done, we can
always just add a length check to the software receive handler
instead of relying on the hardware to do the comparison for us.
What's more, changing the maximum packet size field requires
temporarily disabling the RX/TX paths. So once the link comes
up in 10/100 Mb/s mode or 1000 Mb/s mode, we'd have to disable it
again just to set the right maximum packet size field (1522 in
10/100 Mb/s mode or 9700 in 1000 Mb/s mode), just so that we can
offload one comparison operation to hardware that we might as well
do in software, assuming that we'd want to do it at all.
Contrary to what the documentation suggests, there is no harm in
just setting a 9700 byte maximum packet size in 10/100 mode, so use
the maximum maximum packet size for all modes.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The mv643xx_eth driver allows doing transmit reclaim from within the
napi poll routine, but after doing reclaim, it would forget to check
the free transmit descriptor count and wake up the transmit queue if
the reclaim caused enough descriptors for a new packet to become
available. This would cause the netdev watchdog to occasionally kick
in during certain workloads with combined receive and transmit traffic.
Fix this by adding a wakeup check identical to the one in the
interrupt handler to the napi poll routine.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
When the ethernet link goes down while mv643xx_eth is transmitting
data, transmit DMA can stop before all queued transmit descriptors
have been processed. But even the descriptors that _have_ been
processed might not be properly marked as done before the transmit
DMA unit shuts down.
Then when the link comes up again, the hardware transmit pointer
might have advanced while not all previous packet descriptors have
been marked as transmitted, causing software transmit reclaim to
hang waiting for the hardware to finish transmitting a descriptor
that it has already skipped.
This patch forcibly reclaims all packets on the transmit ring on a
link down interrupt, and then resyncs the hardware transmit pointer to
what the software's idea of the first free descriptor is. Also, we
need to prevent re-waking the transmit queue if we get a 'transmit
done' interrupt at the same time as a 'link down' interrupt, which
this patch does as well.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The previously merged TX hang erratum workaround ("mv643xx_eth:
work around TX hang hardware issue") assumes that TX_END interrupts
are delivered simultaneously with or after their corresponding TX
interrupts, but this is not always true in practise.
In particular, it appears that TX_END interrupts are issued as soon
as descriptor fetch returns an invalid descriptor, which may happen
before earlier descriptors have been fully transmitted and written
back to memory as being done.
This hardware behavior can lead to a situation where the current
driver code mistakenly assumes that the MAC has given up transmitting
before noticing the packets that it is in fact still currently working
on, causing the driver to re-kick the transmit queue, which will only
cause the MAC to re-fetch the invalid head descriptor, and generate
another TX_END interrupt, et cetera, until the packets in the pipe
finally finish transmitting and have their descriptors written back
to memory, which will then finally break the loop.
Fix this by having the erratum workaround not check the 'number of
unfinished descriptor', but instead, to compare the software's idea
of what the head descriptor pointer should be to the hardware's head
descriptor pointer (which is updated on the same conditions as the
TX_END interupt is generated on, i.e. possibly before all previous
descriptors have been transmitted and written back).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (82 commits)
ipw2200: Call netif_*_queue() interfaces properly.
netxen: Needs to include linux/vmalloc.h
[netdrvr] atl1d: fix !CONFIG_PM build
r6040: rework init_one error handling
r6040: bump release number to 0.18
r6040: handle RX fifo full and no descriptor interrupts
r6040: change the default waiting time
r6040: use definitions for magic values in descriptor status
r6040: completely rework the RX path
r6040: call napi_disable when puting down the interface and set lp->dev accordingly.
mv643xx_eth: fix NETPOLL build
r6040: rework the RX buffers allocation routine
r6040: fix scheduling while atomic in r6040_tx_timeout
r6040: fix null pointer access and tx timeouts
r6040: prefix all functions with r6040
rndis_host: support WM6 devices as modems
at91_ether: use netstats in net_device structure
sfc: Create one RX queue and interrupt per CPU package by default
sfc: Use a separate workqueue for resets
sfc: I2C adapter initialisation fixes
...
Stephen Rothwell points out that this file got deleted (on purpose) by
commit 640c1bce86 ("USB: delete airprime
driver"), but then almost immediately incorrectly resurrected by commit
95da310e66 ("usb_serial: API all change").
Delete it again. If it comes back, we'll need to drive a stake through
its heart.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc32: pass -m32 when building vmlinux.lds
sparc: Fixes the DRM layer build on sparc.
ide: merge <asm-sparc/ide_64.h> with <asm-sparc/ide_32.h>
ide: <asm-sparc/ide_64.h>: use __raw_{read,write}w()
ide: <asm-sparc/ide_32.h>: use __raw_{read,write}w()
ide: <asm-sparc/ide_64.h>: use %r0 for outw_be()
sparc64: Do not define BIO_VMERGE_BOUNDARY.
netif_carrier_{on,off}() handles starting and stopping packet
flow into the driver. So there is no reason to invoke netif_stop_queue()
and netif_wake_queue() in response to link status events.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks the error handling in r6040_init_one
in order not to leak resources and correcly unmap and release
PCI regions of the MAC. Also prefix printk's with the driver name
for clarity.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch bumps the release of the r6040 driver. There has been
quite some versions of it out there, but this one is the one
people should report bugs against.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch allows the MAC to handle the RX FIFO full
and no descriptor available interrupts. While we are at it
replace the TX interrupt with its corresponding definition.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch changes the default waiting time of a packet, which
along with our previous r6040_rx path, was causing huge delays
with another host (160 to 230 ms).
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Define all the descriptor status the MAC can set.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch completely reworks the RX path in order to be
more accurate about what is going on with the MAC.
We no longer read the error from the MLSR register instead read
the descriptor status register which reflects, the error per descriptor.
We now allocate skbs on the fly in r6040_rx, and we handle allocation
failure instead of simply dropping the packet. Remove the
rx_free_desc counter of r6040_private structure since we
allocate skbs in the RX path.
r6040_rx_buf_alloc is now removed and becomes unuseless.
Signed-Off-By: Joerg Albert <jal2@gmx.de>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We did not call napi_disabled when putting down the interface
which should be done. Finally initialize lp->dev when everything
is set.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Joseph Fannin <jfannin@gmail.com> and Takashi Iwai <tiwai@suse.de>
noticed that commit 073a345c04
("mv643xx_eth: clarify irq masking and unmasking") broke the
mv643xx_eth build when NETPOLL is enabled, due to it not renaming
one instance of INT_CAUSE_EXT in mv643xx_eth_netpoll(). This patch
takes care of that instance as well.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: Dale Farnsworth <dale@farnsworth.org>
Cc: Joseph Fannin <jfannin@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rework the RX buffers allocation function so that we do not
leak memory in the case we could not allocate skbs for the
RX path. Propagate the errors to the r6040_up function
where we call the RX buffers allocation function.
Also rename the r6040_alloc_txbufs function to
r6040_init_txbufs, to reflect what it really does.
Signed-Off-By: Joerg Albert <jal2@gmx.de>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add a helper function which only modifies R6040 MAC registers
use it when we timeout, and on adapter initialization. Fix
the scheduling while atomic but in the timeout routine due
to the reallocation of rx/tx buffers.
Signed-Off-By: Joerg Albert <jal2@gmx.de>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes a null pointer access in r6040_rx due
to lp->dev not being initialized.
Fix the TX timeouts, TX irq was not re-enabled on RX irq
Signed-Off-By: Joerg Albert <jal2@gmx.de>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Prefix all functions inside the r6040 driver with r6040 to
avoid namespace clashing.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch allows Windows Mobile 6 devices to be used for
tethering -- that is, used as modems. It was requested by
AdamW in kernel bugzilla:
http://bugzilla.kernel.org/show_bug.cgi?id=11119
and Mandriva kernel-discuss list. It is tested and confirmed
to work by Peterl:
http://forum.eeeuser.com/viewtopic.php?pid=323543#p323543
This patch is based on the patch in the above kernel bugzilla,
which is from the usb-rndis-lite tree.
[ dbrownell@users.sourceforge.net: misc fixes ]
Signed-off-by: Thomas Backlund <tmb@mandriva.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use net_device_stats from net_device structure instead of local.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Using multiple cores in the same package to handle received traffic
does not appear to provide a performance benefit. Therefore use CPU
topology information to count CPU packages and use that as the default
number of RX queues and interrupts. We rely on interrupt balancing to
spread the interrupts across packages.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This avoids deadlock in case a reset is triggered during self-test.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As recommended by Jean Delvare:
- Increase timeout to 50 ms
- Leave adapter class clear so that unwanted drivers do not probe our bus
- Use strlcpy() for name initialisation
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch makes e1000 driver ioport-free.
This corrects behavior in probe function so as not to request ioport
resources as long as they are not really needed. This is based on the
ioport-free patch of e1000 driver from Auke Kok and Tomohiro Kusumi.
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@jp.fujitsu.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jeff Kirsher<jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The email linux-nics@intel.com is no longer available, remove all
references.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Redefine DPRINTK macro using do while(0)
__FUNCTION__ to __func__
structs {} on separate lines
Surround negative constants with ()
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use struct e1000_hw *hw = adapter->hw; where necessary
Change macros E1000_READ_REG and E1000_WRITE_REG to er32 and ew32
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
An | in an if statement to check a bit? I think this needs to be a &.
As a result of this typo meth will always operate in promiscuous mode.
Signed-off-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Full patch for the Atheros L1E Gigabit Ethernet driver.
Supportring AR8121, AR8113 and AR8114
Signed-off-by: Jie Yang <jie.yang @atheros.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ixgbe driver was untested with device ID 8086:10c8 but still advertises
support. Currently if this device is present in the system when the driver
is loaded, the system will panic.
Remove this device ID until full support can be tested with available
hardware. This patch is necessary for 2.6.24, 2.6.25 and 2.6.26
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Otherwise it breaks since we merged asm/page.h
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The drivers were touching net queue before it has been started, so
without this patch, the drivers will potentially WARN at
net/core/dev.c:1328.
I don't have the hardware for the drivers below, so this patch is
untested, and thus should be carefully peer reviewed.
tc35815.c
au1000_eth.c
bfin_mac.c
macb.c
^ The four drivers are using phylib, they're calling netif_start_queue()
in open() callback. So trivially remove netif_tx_schedule_all().
Phylib will handle netif_carrier_*().
cpmac.c
fec_mpc52xx.c
fs_enet/fs_enet-main.c
sh_eth.c
^ The same as above, but these were also needlessly calling
netif_carrier_*() functions. So removed queue calls and also remove
carrier calls, since phylib will handle it. fs_enet-main.c also didn't
call netif_start_queue() at open(), this is fixed now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The OQO model 2 has an RTL8139 from Atheros that doesn't like MMIO.
It fails on modprobe, with a 'PCI Bus error' message.
Force it to always use polled IO.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is needed to support devices that only work with PIO without
penalising devices that work fine with MMIO in distro kernels.
It also allows us to eventually use PIO as a fallback when setting
up MMIO fails.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MII_M1111_HWCFG_FIBER_COPPER_RES is a bit of MII_M1111_PHY_EXT_SR, not
MII_M1111_PHY_EXT_CR.
Signed-off-by: Wang Jian <lark@linux.net.cn>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The 27.15 bit (MII_M1111_HWCFG_FIBER_COPPER_AUTO) is disable bit. When
set to 1, copper/fiber auto selection is disabled. The current code
to enable but actually disable auto selection.
Signed-off-by: Wang Jian <lark@linux.net.cn>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/net/igb/igb_main.c:388:20: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Lennert Buytenhek