setting err as -EOVERFLOW for Too many iscsi targets.
Also fixes a spurious compiler warning for gcc 4.3.3 and gcc 4.4 :
CC drivers/scsi/scsi_transport_iscsi.o
drivers/scsi/scsi_transport_iscsi.c: In function ‘iscsi_add_session’:
drivers/scsi/scsi_transport_iscsi.c:678: warning: ‘err’ may be used uninitialized in this function
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The return value from BSG timout function should be based on the state of the
BSG job. This helps block layer to take selective actions to clean up BSG job.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Registered the softirq_done function, since this is requried iby an request
using block level request timeout functionality. This function will be called
by the block layer as part of time out clean process to release the BSG
request.
Moved some of the BSG request completion activities to softirq_done routine to
take care of both normal and timout completions.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This makes a huge difference when you have a serial console on bootup to limit
these messages to a sane number.
Signed-off-by: John Stoffel <john@stoffel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
People keep sending patches to expose CONFIG_SCSI_WAIT_SCAN as a tunable
item. These patches aren't accepted upstream, so let's stop the ongoing
irritation of people due to the unconditionally installed module and its
Kconfig symbol.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fixes a problem seen where sending a PRLI to a target
resulted in it sending a LOGO. This caused the ibmvfc
driver to go back through discovery again, which caused
another PRLI attempt, which caused another LOGO. Fix this
behavior by ignoring LOGO if we haven't even logged into
the target yet.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Since async events could indicate changes to link status, or
events which could affect decisions made during discovery, we should
process async events prior to command completion responses.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds the /sys/module/libfc/parameters/debug_logging
file to sysfs as a module parameter. It accepts an integer
bitmask for logging. Currently it supports:
bit
LSB 0 = general libfc debugging
1 = lport debugging
2 = disc debugging
3 = rport debugging
4 = fcp debugging
5 = EM debugging
6 = exch/seq debugging
7 = scsi logging (mostly error handling)
the other bits are not used at this time.
The patch converts all of the libfc source files to use
these new macros and removes the old FC_DBG macro.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds a 'debug_logging' module parameter to
libfcoe.ko. It is an unsigned int that represents a bitmask of
available debug logging levels, each of which can be tuned at
runtime. Currently there are only two logging levels for this
module-
bit
LSB 0 = libfcoe general logging
1 = FIP logging
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch converts all FC_DBG statements to use new runtime tunable
debug macros. The fcoe.ko module now has a debug_logging module
parameter.
fcoe_debug_logging is an unsigned integer representing a bitmask of all
available logging levels. Currently only two logging levels are
supported-
bit
LSB 0 = general fcoe logging
1 = netdevice related logging
This patch also attempts to clean up some debug statement formatting
so it's more readable.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds support for setting the physical block exponent and
lowest aligned LBA in the READ CAPACITY(16) response.
The B0 VPD page is adjusted accordingly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
NETDEVICES + NETDEV_1000 need to be enabled so that kconfig will check
those branches for selects and enforce "select UIO" under CNIC.
Otherwise the build fails with:
ERROR: "uio_unregister_device" [drivers/net/cnic.ko] undefined!
ERROR: "uio_event_notify" [drivers/net/cnic.ko] undefined!
ERROR: "__uio_register_device" [drivers/net/cnic.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Ingo molnar <mingo@elte.hu> reported the error
drivers/net/cnic.c:2520: error: implicit declaration of function ‘__symbol_get’
when CONFIG_MODULES is not defined. Fix by using symbol_get() instead.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This reverts commit bc3bf8fd33.
All the commit did was add a second #include of <linux/module.h> which is
the wrong fix.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
MSI has only been tested on and known to work with PCI-E based adapters. This
patch adds a field to struct ipr_chip_t to indicate which type of interrupt to
use based on what is known about the chip.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The return value from pci_enable_msi() can not always be trusted. This patch
adds code to generate an interrupt after MSI has been enabled and tests
whether or not we can receive and process it. If the tests fails, then fall
back to LSI.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There have been several bug reports which identified the Ultrium-3
tape as just hanging up on the bus during certain types of IU
transfer. The identified culpret is type 0x02 (MULTIPLE COMMAND)
transfers. The only way to prevent this tape wedging is to prevent it
from using IU transfers at all. So this patch uses the exported
blacklist matching technology to recognise the drive and force it not
to use IU transfers.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Right at the moment, we carefully set up the spi_support_xx in the
device configuration routines, but then we never actually use the
results: we rely on the inquiry strings. If we're going to allow
overrides to the inquiry data, we have to rely on our own internal
settings.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The current scsi_devinfo.c matching routines use a single table for
the global blacklist. However, we're developing a need to blacklist
from specific transports too (notably some tape drives using SPI which
don't respond well to high speed protocols). Instead of developing
separate blacklist matching for each transport class needing it,
enhance the current list matching to permit multiple lists.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Pre-ISP24xx chips have dedicated uses for mailbox 4 and 5 which
software should typically not query nor update.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* To set iiDMA speeds for ISP81XX, bits 5-0 are used whereas for
other older ISPs bits 2-0 are used.
* Pass proper VP index
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Just once, two fcoe instances got the same host number
from scsi_add_host().
Use atomic_t and atomic_inc_return() to get next host number.
Subtract 1, so that scsi_host still starts with 0.
[jejb: added comment about unusual subtraction]
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The SMP handler (sas_smp_request) was fixed to use the block API
properly, so we don't need this workaround to avoid blk_put_request()
warning.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We need to call blk_end_request_all to complete SMP requests properly.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Allow the user to control the debug logs in libiscsi. We will now
have a module param for connection, session & error handling.
[Mike Christie - Fixed up to compile on current code and added
missing ISCSI_DBG_EH conversions]
Signed-off-by: Erez Zilber <erezzi.list@gmail.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The net layer might return -EAGAIN because it could not
get space/mem within the sock sndtimeo or becuase the tcp/ip
connection was down. For the latter we do not want to retry
because the conn/session should just be shutdown and restarted.
libiscsi knows the state of the session recovery so propogate
this error to that layer. It will either do iscsi recovery
or have us retry the operation. Right now if we have partially
sent a pdu we would always retry the IO xmit slowing down
recovery.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If we are sending or receiving data for the task successfully do
not run the scsi eh, because we know the task is making progress.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The default kernel pages supported are 4K, 8K, 16K, and 64K. Re-calculate
entries if PAGE_SIZE is not one of the defaults.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The iscsi ddp functionality could be used by multiple iscsi entities,
add a refcnt to keep track of it, so we would not release it pre-maturely.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Query the block limits VPD page and adjust queue minimum and optimal I/O
sizes.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Detect non-rotational devices and set the queue flag accordingly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Extract physical block size and lowest aligned LBA from READ
CAPACITY(16) response and adjust queue parameters.
Report physical block size and alignment when applicable.
[jejb: fix up trailing whitespace]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
da456f1 "page allocator: do not disable interrupts in free_page_mlock()" moved
the PG_mlocked clearing after the flag sanity checking which makes mlocked
pages always trigger 'bad page'. Fix this by clearing the bit up front.
Reported--and-debugged-by: Peter Chubb <peter.chubb@nicta.com.au>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The discussion about using "access_ok()" in get_user_pages_fast() (see
commit 7f8189068726492950bf1a2dcfd9b51314560abf: "x86: don't use
'access_ok()' as a range check in get_user_pages_fast()" for details and
end result), made us notice that x86-64 was really being very sloppy
about virtual address checking.
So be way more careful and straightforward about masking x86-64 virtual
addresses:
- All the VIRTUAL_MASK* variants now cover half of the address
space, it's not like we can use the full mask on a signed
integer, and the larger mask just invites mistakes when
applying it to either half of the 48-bit address space.
- /proc/kcore's kc_offset_to_vaddr() becomes a lot more
obvious when it transforms a file offset into a
(kernel-half) virtual address.
- Unify/simplify the 32-bit and 64-bit USER_DS definition to
be based on TASK_SIZE_MAX.
This cleanup and more careful/obvious user virtual address checking also
uncovered a buglet in the x86-64 implementation of strnlen_user(): it
would do an "access_ok()" check on the whole potential area, even if the
string itself was much shorter, and thus return an error even for valid
strings. Our sloppy checking had hidden this.
So this fixes 'strnlen_user()' to do this properly, the same way we
already handled user strings in 'strncpy_from_user()'. Namely by just
checking the first byte, and then relying on fault handling for the
rest. That always works, since we impose a guard page that cannot be
mapped at the end of the user space address space (and even if we
didn't, we'd have the address space hole).
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq, irq.h: Fix kernel-doc warnings
genirq: fix comment to say IRQ_WAKE_THREAD
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (49 commits)
perfcounter: Handle some IO return values
perf_counter: Push perf_sample_data through the swcounter code
perf_counter tools: Define and use our own u64, s64 etc. definitions
perf_counter: Close race in perf_lock_task_context()
perf_counter, x86: Improve interactions with fast-gup
perf_counter: Simplify and fix task migration counting
perf_counter tools: Add a data file header
perf_counter: Update userspace callchain sampling uses
perf_counter: Make callchain samples extensible
perf report: Filter to parent set by default
perf_counter tools: Handle lost events
perf_counter: Add event overlow handling
fs: Provide empty .set_page_dirty() aop for anon inodes
perf_counter: tools: Makefile tweaks for 64-bit powerpc
perf_counter: powerpc: Add processor back-end for MPC7450 family
perf_counter: powerpc: Make powerpc perf_counter code safe for 32-bit kernels
perf_counter: powerpc: Change how processor-specific back-ends get selected
perf_counter: powerpc: Use unsigned long for register and constraint values
perf_counter: powerpc: Enable use of software counters on 32-bit powerpc
perf_counter tools: Add and use isprint()
...
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix out of scope variable access in sched_slice()
sched: Hide runqueues from direct refer at source code level
sched: Remove unneeded __ref tag
sched, x86: Fix cpufreq + sched_clock() TSC scaling
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (24 commits)
tracing/urgent: warn in case of ftrace_start_up inbalance
tracing/urgent: fix unbalanced ftrace_start_up
function-graph: add stack frame test
function-graph: disable when both x86_32 and optimize for size are configured
ring-buffer: have benchmark test print to trace buffer
ring-buffer: do not grab locks in nmi
ring-buffer: add locks around rb_per_cpu_empty
ring-buffer: check for less than two in size allocation
ring-buffer: remove useless compile check for buffer_page size
ring-buffer: remove useless warn on check
ring-buffer: use BUF_PAGE_HDR_SIZE in calculating index
tracing: update sample event documentation
tracing/filters: fix race between filter setting and module unload
tracing/filters: free filter_string in destroy_preds()
ring-buffer: use commit counters for commit pointer accounting
ring-buffer: remove unused variable
ring-buffer: have benchmark test handle discarded events
ring-buffer: prevent adding write in discarded area
tracing/filters: strloc should be unsigned short
tracing/filters: operand can be negative
...
Fix up kmemcheck-induced conflict in kernel/trace/ring_buffer.c manually
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (45 commits)
x86, mce: fix error path in mce_create_device()
x86: use zalloc_cpumask_var for mce_dev_initialized
x86: fix duplicated sysfs attribute
x86: de-assembler-ize asm/desc.h
i386: fix/simplify espfix stack switching, move it into assembly
i386: fix return to 16-bit stack from NMI handler
x86, ioapic: Don't call disconnect_bsp_APIC if no APIC present
x86: Remove duplicated #include's
x86: msr.h linux/types.h is only required for __KERNEL__
x86: nmi: Add Intel processor 0x6f4 to NMI perfctr1 workaround
x86, mce: mce_intel.c needs <asm/apic.h>
x86: apic/io_apic.c: dmar_msi_type should be static
x86, io_apic.c: Work around compiler warning
x86: mce: Don't touch THERMAL_APIC_VECTOR if no active APIC present
x86: mce: Handle banks == 0 case in K7 quirk
x86, boot: use .code16gcc instead of .code16
x86: correct the conversion of EFI memory types
x86: cap iomem_resource to addressable physical memory
x86, mce: rename _64.c files which are no longer 64-bit-specific
x86, mce: mce.h cleanup
...
Manually fix up trivial conflict in arch/x86/mm/fault.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (35 commits)
Input: add driver for Synaptics I2C touchpad
Input: synaptics - add support for reporting x/y resolution
Input: ALPS - handle touchpoints buttons correctly
Input: gpio-keys - change timer to workqueue
Input: ads7846 - pin change interrupt support
Input: add support for touchscreen on W90P910 ARM platform
Input: appletouch - improve finger detection
Input: wacom - clear Intuos4 wheel data when finger leaves proximity
Input: ucb1400 - move static function from header into core
Input: add driver for EETI touchpanels
Input: ads7846 - more detailed model name in sysfs
Input: ads7846 - support swapping x and y axes
Input: ati_remote2 - use non-atomic bitops
Input: introduce lm8323 keypad driver
Input: psmouse - ESD workaround fix for OLPC XO touchpad
Input: tsc2007 - make sure platform provides get_pendown_state()
Input: uinput - flush all pending ff effects before destroying device
Input: simplify name handling for certain input handles
Input: serio - do not use deprecated dev.power.power_state
Input: wacom - add support for Intuos4 tablets
...
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (24 commits)
agp/intel: Make intel_i965_mask_memory use dma_addr_t for physical addresses
agp: add user mapping support to ATI AGP bridge.
drm/i915: enable GEM on PAE.
drm/radeon: fix unused variables warning
agp: switch AGP to use page array instead of unsigned long array
agpgart: detected ALi M???? chipset with M1621
drm/radeon: command stream checker for r3xx-r5xx hardware
drm/radeon: Fully initialize LVDS info also when we can't get it from the ROM.
radeon: Fix CP byte order on big endian architectures with KMS.
agp/uninorth: Handle user memory types.
drm/ttm: Add some powerpc cache flush code.
radeon: Enable modesetting on non-x86.
drm/radeon: Respect AGP cant_use_aperture flag.
drm: EDID endianness fixes.
drm/radeon: this VRAM vs aperture test is wrong, just remove it.
drm/ttm: fix an error path to exit function correctly
drm: Apply "Memory fragmentation from lost alignment blocks"
ttm: Return -ERESTART when a signal interrupts bo eviction.
drm: Remove memory debugging infrastructure.
drm/i915: Clear fence register on tiling stride change.
...
It's really not right to use 'access_ok()', since that is meant for the
normal "get_user()" and "copy_from/to_user()" accesses, which are done
through the TLB, rather than through the page tables.
Why? access_ok() does both too few, and too many checks. Too many,
because it is meant for regular kernel accesses that will not honor the
'user' bit in the page tables, and because it honors the USER_DS vs
KERNEL_DS distinction that we shouldn't care about in GUP. And too few,
because it doesn't do the 'canonical' check on the address on x86-64,
since the TLB will do that for us.
So instead of using a function that isn't meant for this, and does
something else and much more complicated, just do the real rules: we
don't want the range to overflow, and on x86-64, we want it to be a
canonical low address (on 32-bit, all addresses are canonical).
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jaswinder Singh Rajput