The following patch adds support for the Barco LPT->DVI I2C adapter to
the i2c-parport driver.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove duplicate of BCD macros.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch clarifies the W83627THF VID documentation.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the VID reading; no cpu0_vid and vrm files created if
the chip is w83627thf and GPIO5 not enabled.
Signed-off-by: Yuan Mu <ymu@winbond.com.tw>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers, hwmon, adm1025 and adm1026: remove deprecated sysfs names.
these names have been listed for removal for six months, time for them to go
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add code to handle case where board firmware does not start the
RTC.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
CC: James Chapman <jchapman@katalix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch tweaks i2c-i801.c so that the driver always sets the SMBAUXCTL
register (which enables/disables PEC) explicitly before each transaction.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These patches add the header linux/if_ether.h and change 1500 to
ETH_DATA_LEN in some files.
Signed-off-by: Kris Katterjohn <kjak@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some PCMCIA device IDs for the microdrive found in the Sharp Zaurus
and a different revision of the Socket CF+ Bluetooth card.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
kill the socket_shutdown()/shutdown_socket() confusion by making it
one single function. move cs_socket_put() in there. nicer to read and
smaller:
original:
text data bss dec hex filename
25181 1076 32 26289 66b1 drivers/pcmcia/pcmcia_core.ko
patched:
text data bss dec hex filename
24973 1076 32 26081 65e1 drivers/pcmcia/pcmcia_core.ko
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Export the stored values instead of re-reading everything in the socket
information sysfs files, and make them accessible to all users, not only
to root.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This adds PCMCIA support for both MPC885ADS and MPC866ADS.
This is established not together with FADS, because 885 does not have
io_block_mapping() for BCSR area.
Also, some cleanups done both for 885ADS and MBX.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This fixes misconfiguration that could result in odd work of some old CF
cards.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Some PCMCIA sockets have statically mapped memory windows, but dynamically
mapped IO windows. Using the "nonstatic" socket library is inpractical for
them, as they do neither need a resource database (as we can trust the
kernel resource database on m68k and ppc) nor lots of other features of that
library. Let them get a small "iodyn" socket library (105 lines of code)
instead.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Update the PCMCIA sound drivers to handle the recent changes to the PCMCIA
core. A part of this merge was done by Takashi Iwai <tiwai@suse.de>.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Unify the EVENT_CARD_INSERTION and "attach" callbacks to one unified
probe() callback. As all in-kernel drivers are changed to this new
callback, there will be no temporary backwards-compatibility. Inside a
probe() function, each driver _must_ set struct pcmcia_device
*p_dev->instance and instance->handle correctly.
With these patches, the basic driver interface for 16-bit PCMCIA drivers
now has the classic four callbacks known also from other buses:
int (*probe) (struct pcmcia_device *dev);
void (*remove) (struct pcmcia_device *dev);
int (*suspend) (struct pcmcia_device *dev);
int (*resume) (struct pcmcia_device *dev);
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The linked list of devices managed by each PCMCIA driver is, in very most
cases, unused. Therefore, remove it from many drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Unify the "detach" and REMOVAL_EVENT handlers to one "remove" function.
Old functionality is preserved, for the moment.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Merge the suspend and resume methods for 16-bit PCMCIA cards into the
device model -- for both runtime power management and suspend to ram/disk.
Bugfix in ds.c by Richard Purdie
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Move the suspend and resume methods out of the event handler, and into
special functions. Also use these functions for pre- and post-reset, as
almost all drivers already do, and the remaining ones can easily be
converted.
Bugfix to include/pcmcia/ds.c
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Make the bridge specific initialization code config options depending on
CONFIG_EMBEDDED. Config options for TI/EnE, Toshiba, Ricoh and O2Micro are
available. Disabling all of the specific tweaks cuts off more than half
of yenta_socket.ko.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Also return a value if CONFIG_PCMCIA_PROBE is not set.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Add a return value to pcmcia_validate_mem. Only if we have enough memory
available to map the CIS, we should proceed in trying to determine information
about the device.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Don't waste cpu time in yenta interrupt handler when the interrupt was for
another device.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
arch/ia64/kernel/setup.c: In function `show_cpuinfo':
arch/ia64/kernel/setup.c:576: warning: long unsigned int format, different type arg (arg 12)
arch/ia64/kernel/setup.c:576: warning: long unsigned int format, different type arg (arg 13)
Introduced by 95235ca2c2
Signed-off-by: Tony Luck <tony.luck@intel.com>
I have recently been switching from using 2.4.32 on my trusty
old Sparc Blade 100 to using 2.6.15 . Some of the problems I ran into
were distorted video when the console was active (missing first
character, skipped dots) and when running X windows (colored snow,
stripes, missing pixels). A quick examination of the 2.6 versus 2.4
source for the ATY driver revealed alot of changes.
A closer look at the code/data for the 64GR/XL chip revealed
two minor "typos" that the rewriter(s) of the code made. The first is
a incorrect clock value (230 .vs. 235) and the second is a missing
flag (M64F_SDRAM_MAGIC_PLL). Making both these changes seems to have
fixed my problem. I tend to think the 235 value is the correct one,
as there is a 29.4 Mhz clock crystal close to the video chip and 235.2
(29.4*8) is too close to 235 to make it a coincidence.
The flag for M64F_SDRAM_MAGIC_PLL was dropped during the
changes made by adaplas in file revision 1.72 on the old bitkeeper
repository.
The change relating to the clock rate has been there forever,
at least in the 2.6 tree. I'm not sure where to look for the old 2.5
tree or if anyone cares when it happened.
On SPARC Blades 100's, which use the ATY MACH64GR video chipset, the
clock crystal frequency is 235.2 Mhz, not 230 Mhz. The chipset also
requires the use of M64F_SDRAM_MAGIC_PLL in order to setup the PLL
properly for the DRAM.
Signed-off-by: Luis F. Ortiz <lfo@Polyad.Org>
Signed-off-by: David S. Miller <davem@davemloft.net>
HOPLIMIT metric is appropriate to TCP reset sent by REJECT target
than hard-coded max TTL. Thanks to David S. Miller for hint.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC [M] net/ipv4/netfilter/nf_conntrack_l3proto_ipv4.o
net/ipv4/netfilter/nf_conntrack_l3proto_ipv4.c: In function 'ipv4_refrag':
net/ipv4/netfilter/nf_conntrack_l3proto_ipv4.c:198: error: dereferencing pointer to incomplete type
make[3]: *** [net/ipv4/netfilter/nf_conntrack_l3proto_ipv4.o] Error 1
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original ipv6_find_hdr() finds the specified header in IPv6 packets.
This makes it possible to get transport header so that we can kill similar
loop in ip6_match_packet().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call POST_ROUTING hook before fragmentation to get rid of the okfn use
in ip_refrag and save the useless fragmentation/defragmentation step
when NAT is used.
The patch introduces one user-visible change, the POSTROUTING chain
in the mangle table gets entire packets, not fragments, which should
simplify use of the MARK and CLASSIFY targets for queueing as a nice
side-effect.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
okfn should only be used from different contexts to avoid deep call chains,
i.e. by nf_queue.
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Properly dump the helper name instead of internal kernel data.
Based on patch by Marcus Sundberg <marcus@ingate.com>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix netfilter module_param types and permissions. Also fix an off-by-one in
the ipt_ULOG nlbufsiz < 128k check.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump entries of a given Layer 3 protocol number.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set conntrack mark before it is in hashes.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Korsgaard