CFE is the only supported and used bootloader on the SiByte boards,
the standalone kernel support has been never used outside Broadcom.
Remove it and make the kernel use CFE by default.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes the SiByte simulation Kconfig option, which only modified
a printk.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch makes sure that we are not going to clear
or change the interrupt status of a GPIO interrupt
superior to 13 as this is the maximum number of GPIO
interrupt source (p.232 of the RC32434 reference manual).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CPU_CAVIUM_OCTEON is mips_r2 which is handled before the switch. This
label in the switch statement is dead code, so we remove it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Reviewed by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Octeon has no execution hazards, so we can remove them and save an
instruction per TLB handler invocation.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Reviewed by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some CPUs do not need ehb instructions after writing CP0 registers.
By allowing ehb generation to be overridden in
cpu-feature-overrides.h, we can save a few instructions in the TLB
handler hot paths.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Try to fold the 64-bit TLB refill handler opportunistically at the
beginning of the vmalloc path so as to avoid splitting execution flow in
half and wasting cycles for a branch required at that point then. Resort
to doing the split if either of the newly created parts would not fit into
its designated slot.
Original-patch-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The logic used to split the r4000 refill handler is liberally
sprinkled with magic numbers. We attempt to explain what they are and
normalize them against a new symbolic value (MIPS64_REFILL_INSNS).
CC: David VomLehn <dvomlehn@cisco.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add platform support for ACLC of TXx9 SoCs.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for PCI and PCIe to the base Cavium OCTEON
processor support.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Here we add the register definitions for the processor blocks used by
the following PCI support patch.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the integrated DMAC of the TXx9 family.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use container structure for clocksource, clock_event_device and hold a
pointer to txx9_tmr_reg in it.
This saves a few instructions in clocksource and clock_event handlers.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A wrong resolution of a merge conflict made the recently deleted wrong
error check in sb1250_set_affinity. Send the zombie back to the empire
of the undead.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'next-i2c' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-stu300: Make driver depend on MACH_U300
i2c-s3c2410: use resource_size()
i2c: Use resource_size macro
i2c: ST DDC I2C U300 bus driver v3
i2c-bfin-twi: pull in io.h for ioremap()
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: switch to using late_initcall
radeon legacy chips: tv dac bg/dac adj updates
drm/radeon: introduce kernel modesetting for radeon hardware
drm: Add the TTM GPU memory manager subsystem.
drm: Memory fragmentation from lost alignment blocks
drm/radeon: fix mobility flags on new PCI IDs.
Authentication error abort codes should be translated to appropriate
Linux error codes, rather than all being translated to EREMOTEIO - which
indicates that the server had internal problems.
Additionally, a server shouldn't be marked unavailable and the next
server tried if an authentication error occurs. This will quickly make
all the servers unavailable to the client. Instead the error should be
returned straight to the user.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Connections that have seen a connection-level abort should not be reused
as the far end will just abort them again; instead a new connection
should be made.
Connection-level aborts occur due to such things as authentication
failures.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some architectures need to initialize SLAB caches to be able
to allocate page tables. They do that from pgtable_cache_init()
so the later should be called earlier now, best is before
vmalloc_init().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* akpm: (182 commits)
fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset
fbdev: *bfin*: fix __dev{init,exit} markings
fbdev: *bfin*: drop unnecessary calls to memset
fbdev: bfin-t350mcqb-fb: drop unused local variables
fbdev: blackfin has __raw I/O accessors, so use them in fb.h
fbdev: s1d13xxxfb: add accelerated bitblt functions
tcx: use standard fields for framebuffer physical address and length
fbdev: add support for handoff from firmware to hw framebuffers
intelfb: fix a bug when changing video timing
fbdev: use framebuffer_release() for freeing fb_info structures
radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb?
s3c-fb: CPUFREQ frequency scaling support
s3c-fb: fix resource releasing on error during probing
carminefb: fix possible access beyond end of carmine_modedb[]
acornfb: remove fb_mmap function
mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF
mb862xxfb: restrict compliation of platform driver to PPC
Samsung SoC Framebuffer driver: add Alpha Channel support
atmel-lcdc: fix pixclock upper bound detection
offb: use framebuffer_alloc() to allocate fb_info struct
...
Manually fix up conflicts due to kmemcheck in mm/slab.c
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The remove member of the platform_driver bfin_t350mcqb_driver should use
__devexit_p() to refer to the remove function, and that function should
get __devexit markings. Likewise, the probe function should be marked
with __devinit and not __init.
Also, module_init() functions should be marked with __init rather than
__devinit.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The dma_alloc_* functions sets the memory to 0 before returning so there
is no need to call memset after the allocation. Also no point in clearing
the memory when disabling the buffer.
Signed-off-by: Vivek Kutal <vivek.kutal@azingo.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The local fbinfo/info vars in the suspend functions don't actually get
used which cause ugly gcc warnings, so drop them.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add accelerated bitblt functions to s1d13xxx based video chipsets, more
specificly functions copyarea and fillrect.
It has only been tested and activated for 13506 chipsets but is expected
to work for the majority of s1d13xxx based chips. This patch also cleans
up the driver with respect of whitespaces and other formatting issues. We
update the current status comments.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use standard fields fbinfo.fix.smem_start and fbinfo.fix.smem_len for
physical address and length of framebuffer.
This also fixes output of the 'fbset -i' command - address and length of
the framebuffer are displayed correctly.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With KMS we have ran into an issue where we really want the KMS fb driver
to be the one running the console, so panics etc can be shown by switching
out of X etc.
However with vesafb/efifb built-in, we end up with those on fb0 and the
KMS fb driver on fb1, driving the same piece of hw, so this adds an fb
info flag to denote a firmware fbdev, and adds a new aperture base/size
range which can be compared when the hw drivers are installed to see if
there is a conflict with a firmware driver, and if there is the firmware
driver is unregistered and the hw driver takes over.
It uses new aperture_base/size members instead of comparing on the fix
smem_start/length, as smem_start/length might for example only cover the
first 1MB of the PCI aperture, and we could allocate the kms fb from 8MB
into the aperture, thus they would never overlap.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dave Airlie <airlied@redhat.com>
Acked-by: Peter Jones <pjones@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When changing video timing dynamically via fbset the screen sporadically
is rendered black.
With the attached fix which disables VCO prior to timing register change
the problem disappears.
I had a look at the Xserver register setup code. Here the VCO is
disabled in the same way [1].
This patch is taken from vga-sync-field version 0.0.11 [2][3].
[1] http://cgit.freedesktop.org/xorg/driver/xf86-video-intel/tree/src/i830_=
driver.c
[2] http://lowbyte.de/vga-sync-fields/vga-sync-fields-0.0.11.tgz
[3] http://easy-vdr.de/git?p=frc.git/.git;a=commit;h=dcc3b863e5a663652587619c357bd20075af6896
2587619c357bd20075af6896
Signed-off-by: Thomas Hilber <sparkie@lowbyte.de>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the framebuffer_release() for freeing fb_info structures allocated
with framebuffer_alloc().
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
P2G2CLK_ALWAYS_ONb is tested twice, 2nd should be P2G2CLK_DAC_ALWAYS_ONb.
[akpm@linux-foundation.org: remove duplicated bitwise-OR of PIXCLKS_CNTL__R300_P2G2CLK_ALWAYS_ONb too]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for CPU frequency scaling in the S3C24XX video driver.
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All resources are released in s3c_fb_win_release so remove other places of
resources releasing. Add releasing of an allocated fb_info structure as
well.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This check is off-by-one.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver's fb_mmap function is essentially the same as a generic fb_mmap
function. Delete driver's function and use the generic one.
A difference is that generic function marks frame buffer memory as VM_IO |
VM_RESERVED. The driver's function marks it as VM_IO only.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With this change, the driver builds fine on Microblaze, which helps
allyesconfig compile tests.
I did not test sparc, but the change should have the same effect there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Anatolij Gustschin <agust@denx.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The OpenFirmware part of this driver is uncompilable on SPARC due to it's
dependance on several PPC specific functions.
Restricting this to PPC to prevent these build errors:
CC drivers/video/mb862xx/mb862xxfb.o
drivers/video/mb862xx/mb862xxfb.c: In function 'of_platform_mb862xx_probe':
drivers/video/mb862xx/mb862xxfb.c:559: error: implicit declaration of function 'of_address_to_resource'
drivers/video/mb862xx/mb862xxfb.c:575: error: 'NO_IRQ' undeclared (first use in this function)
drivers/video/mb862xx/mb862xxfb.c:575: error: (Each undeclared identifier is reported only once
drivers/video/mb862xx/mb862xxfb.c:575: error: for each function it appears in.)
This was found using randconfig builds.
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the ARGB1888 and ARGB4888 hardware to the Samsung SoC
Framebuffer driver (s3c-fb.c).
ARGB1888 and ARGB4888 is decided by var->transp.length and this variable
is set by s3c_fb_check_var().
In s3c_fb_check_var(), if var->vits_per_pixel is 25 or 28, then
var->transp.length would be 1 or 3.
Therefore alpha mode(ARGB1888 or ARGB4888) could be decided through that
variable.
For using alpha mode, you need to set the following: This code should be
added to your machine code as platform data.
static struct s3c_fb_pd_win xxx_fb_win0 = {
/* this is to ensure we use win0 */
.win_mode = {
.pixclock = (8+8+8+240)*(38+4+38+400),
.left_margin = 8,
.right_margin = 8,
.upper_margin = 38,
.lower_margin = 38,
.hsync_len = 8,
.vsync_len = 4,
.xres = 240,
.yres = 400,
},
.max_bpp = 32,
.default_bpp = 24,
};
static struct s3c_fb_pd_win xxx_fb_win1 = {
.win_mode = {
.pixclock = (8+8+8+240)*(38+4+38+400),
.left_margin = 8,
.right_margin = 8,
.upper_margin = 38,
.lower_margin = 38,
.hsync_len = 8,
.vsync_len = 4,
.xres = 240,
.yres = 400,
},
.max_bpp = 32,
.default_bpp = 28,
};
static struct s3c_fb_platdata xxx_lcd_pdata __initdata = {
.win[0] = &ncp_fb_win0,
.win[1] = &ncp_fb_win1,
.vidcon0 = VIDCON0_VIDOUT_RGB | VIDCON0_PNRMODE_RGB,
.vidcon1 = VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC,
.setup_gpio = xxx_fb_gpio_setup,
};
s3c_fb_set_platdata(&xxx_lcd_pdata);
The above code sets pixelformat for window0 layer to RGB888 and window1
layer to ARGB4888.
Signed-off-by: InKi Dae <inki.dae@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kyungmin Park <kmpark@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
AFAICT the code which checks that the requested pixclock value is within
bounds is incorrect. It ensures that the lcdc core clock is at least
(bytes per pixel) times higher than the pixel clock rather than just
greater than or equal to.
There are tighter restrictions on the pixclock value as a function of bus
width for STN panels but even then it isn't a simple relationship as
currently checked for. IMO either something like the below patch should
be applied or else more detailed checking logic should be implemented
which takes in to account the panel type as well.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Daniel Glockner <dg@emlix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the framebuffer_alloc() function to allocate the fb_info structure so
the structure is correctly initialized after allocation.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the framebuffer_alloc() function to allocate the fb_info
structure so the structure is correctly initialized after allocation.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Imre Kaloz