net: ethernet: realtek: atp: checkpatch errors and warnings corrected

Several warnings and errors of coding style rules corrected.
Compile tested.

Signed-off-by: Roberto Medina <robertoxmed@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/realtek/atp.h

@@ -29,9 +29,10 @@ struct rx_header {
 #define RdAddr	0xC0
 #define HNib	0x10
 
-enum page0_regs
-{
-    /* The first six registers hold the ethernet physical station address. */
+enum page0_regs {
+	/* The first six registers hold
+	 * the ethernet physical station address.
+	 */
 	PAR0 = 0, PAR1 = 1, PAR2 = 2, PAR3 = 3, PAR4 = 4, PAR5 = 5,
 	TxCNT0 = 6, TxCNT1 = 7,		/* The transmit byte count. */
 	TxSTAT = 8, RxSTAT = 9,		/* Tx and Rx status. */
@@ -40,11 +41,13 @@ enum page0_regs
 	CMR2 = 13,			/* Command register 2. */
 	MODSEL = 14,		/* Mode select register. */
 	MAR = 14,			/* Memory address register (?). */
-    CMR2_h = 0x1d, };
-
-enum eepage_regs
-{ PROM_CMD = 6, PROM_DATA = 7 };	/* Note that PROM_CMD is in the "high" bits. */
+	CMR2_h = 0x1d,
+};
 
+enum eepage_regs {
+	PROM_CMD = 6,
+	PROM_DATA = 7	/* Note that PROM_CMD is in the "high" bits. */
+};
 
 #define ISR_TxOK	0x01
 #define ISR_RxOK	0x04
@@ -72,20 +75,24 @@ enum eepage_regs
 #define CMR2h_Normal	2	/* Accept physical and broadcast address. */
 #define CMR2h_PROMISC	3	/* Promiscuous mode. */
 
-/* An inline function used below: it differs from inb() by explicitly return an unsigned
-   char, saving a truncation. */
+/* An inline function used below: it differs from inb() by explicitly
+ * return an unsigned char, saving a truncation.
+ */
 static inline unsigned char inbyte(unsigned short port)
 {
 	unsigned char _v;
+
 	__asm__ __volatile__ ("inb %w1,%b0" : "=a" (_v) : "d" (port));
 	return _v;
 }
 
 /* Read register OFFSET.
-   This command should always be terminated with read_end(). */
+ * This command should always be terminated with read_end().
+ */
 static inline unsigned char read_nibble(short port, unsigned char offset)
 {
 	unsigned char retval;
+
 	outb(EOC+offset, port + PAR_DATA);
 	outb(RdAddr+offset, port + PAR_DATA);
 	inbyte(port + PAR_STATUS);	/* Settling time delay */
@@ -151,6 +158,7 @@ static inline void
 write_reg(short port, unsigned char reg, unsigned char value)
 {
 	unsigned char outval;
+
 	outb(EOC | reg, port + PAR_DATA);
 	outval = WrAddr | reg;
 	outb(outval, port + PAR_DATA);
@@ -190,6 +198,7 @@ static inline void
 write_reg_byte(short port, unsigned char reg, unsigned char value)
 {
 	unsigned char outval;
+
 	outb(EOC | reg, port + PAR_DATA); /* Reset the address register. */
 	outval = WrAddr | reg;
 	outb(outval, port + PAR_DATA);
@@ -205,8 +214,7 @@ write_reg_byte(short port, unsigned char reg, unsigned char value)
 	outb(EOC  | value, port + PAR_DATA); /* Reset the address register. */
 }
 
-/*
- * Bulk data writes to the packet buffer.  The interrupt line remains enabled.
+/* Bulk data writes to the packet buffer.  The interrupt line remains enabled.
  * The first, faster method uses only the dataport (data modes 0, 2 & 4).
  * The second (backup) method uses data and control regs (modes 1, 3 & 5).
  * It should only be needed when there is skew between the individual data