You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
276 lines
6.5 KiB
276 lines
6.5 KiB
/*
|
|
* this file included by nicstar.c
|
|
*/
|
|
|
|
/*
|
|
* nicstarmac.c
|
|
* Read this ForeRunner's MAC address from eprom/eeprom
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
|
|
typedef void __iomem *virt_addr_t;
|
|
|
|
#define CYCLE_DELAY 5
|
|
|
|
/* This was the original definition
|
|
#define osp_MicroDelay(microsec) \
|
|
do { int _i = 4*microsec; while (--_i > 0) { __SLOW_DOWN_IO; }} while (0)
|
|
*/
|
|
#define osp_MicroDelay(microsec) {unsigned long useconds = (microsec); \
|
|
udelay((useconds));}
|
|
|
|
|
|
/* The following tables represent the timing diagrams found in
|
|
* the Data Sheet for the Xicor X25020 EEProm. The #defines below
|
|
* represent the bits in the NICStAR's General Purpose register
|
|
* that must be toggled for the corresponding actions on the EEProm
|
|
* to occur.
|
|
*/
|
|
|
|
/* Write Data To EEProm from SI line on rising edge of CLK */
|
|
/* Read Data From EEProm on falling edge of CLK */
|
|
|
|
#define CS_HIGH 0x0002 /* Chip select high */
|
|
#define CS_LOW 0x0000 /* Chip select low (active low)*/
|
|
#define CLK_HIGH 0x0004 /* Clock high */
|
|
#define CLK_LOW 0x0000 /* Clock low */
|
|
#define SI_HIGH 0x0001 /* Serial input data high */
|
|
#define SI_LOW 0x0000 /* Serial input data low */
|
|
|
|
/* Read Status Register = 0000 0101b */
|
|
#if 0
|
|
static u_int32_t rdsrtab[] =
|
|
{
|
|
CS_HIGH | CLK_HIGH,
|
|
CS_LOW | CLK_LOW,
|
|
CLK_HIGH, /* 0 */
|
|
CLK_LOW,
|
|
CLK_HIGH, /* 0 */
|
|
CLK_LOW,
|
|
CLK_HIGH, /* 0 */
|
|
CLK_LOW,
|
|
CLK_HIGH, /* 0 */
|
|
CLK_LOW,
|
|
CLK_HIGH, /* 0 */
|
|
CLK_LOW | SI_HIGH,
|
|
CLK_HIGH | SI_HIGH, /* 1 */
|
|
CLK_LOW | SI_LOW,
|
|
CLK_HIGH, /* 0 */
|
|
CLK_LOW | SI_HIGH,
|
|
CLK_HIGH | SI_HIGH /* 1 */
|
|
};
|
|
#endif /* 0 */
|
|
|
|
|
|
/* Read from EEPROM = 0000 0011b */
|
|
static u_int32_t readtab[] =
|
|
{
|
|
/*
|
|
CS_HIGH | CLK_HIGH,
|
|
*/
|
|
CS_LOW | CLK_LOW,
|
|
CLK_HIGH, /* 0 */
|
|
CLK_LOW,
|
|
CLK_HIGH, /* 0 */
|
|
CLK_LOW,
|
|
CLK_HIGH, /* 0 */
|
|
CLK_LOW,
|
|
CLK_HIGH, /* 0 */
|
|
CLK_LOW,
|
|
CLK_HIGH, /* 0 */
|
|
CLK_LOW,
|
|
CLK_HIGH, /* 0 */
|
|
CLK_LOW | SI_HIGH,
|
|
CLK_HIGH | SI_HIGH, /* 1 */
|
|
CLK_LOW | SI_HIGH,
|
|
CLK_HIGH | SI_HIGH /* 1 */
|
|
};
|
|
|
|
|
|
/* Clock to read from/write to the eeprom */
|
|
static u_int32_t clocktab[] =
|
|
{
|
|
CLK_LOW,
|
|
CLK_HIGH,
|
|
CLK_LOW,
|
|
CLK_HIGH,
|
|
CLK_LOW,
|
|
CLK_HIGH,
|
|
CLK_LOW,
|
|
CLK_HIGH,
|
|
CLK_LOW,
|
|
CLK_HIGH,
|
|
CLK_LOW,
|
|
CLK_HIGH,
|
|
CLK_LOW,
|
|
CLK_HIGH,
|
|
CLK_LOW,
|
|
CLK_HIGH,
|
|
CLK_LOW
|
|
};
|
|
|
|
|
|
#define NICSTAR_REG_WRITE(bs, reg, val) \
|
|
while ( readl(bs + STAT) & 0x0200 ) ; \
|
|
writel((val),(base)+(reg))
|
|
#define NICSTAR_REG_READ(bs, reg) \
|
|
readl((base)+(reg))
|
|
#define NICSTAR_REG_GENERAL_PURPOSE GP
|
|
|
|
/*
|
|
* This routine will clock the Read_Status_reg function into the X2520
|
|
* eeprom, then pull the result from bit 16 of the NicSTaR's General Purpose
|
|
* register.
|
|
*/
|
|
#if 0
|
|
u_int32_t
|
|
nicstar_read_eprom_status( virt_addr_t base )
|
|
{
|
|
u_int32_t val;
|
|
u_int32_t rbyte;
|
|
int32_t i, j;
|
|
|
|
/* Send read instruction */
|
|
val = NICSTAR_REG_READ( base, NICSTAR_REG_GENERAL_PURPOSE ) & 0xFFFFFFF0;
|
|
|
|
for (i=0; i<ARRAY_SIZE(rdsrtab); i++)
|
|
{
|
|
NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE,
|
|
(val | rdsrtab[i]) );
|
|
osp_MicroDelay( CYCLE_DELAY );
|
|
}
|
|
|
|
/* Done sending instruction - now pull data off of bit 16, MSB first */
|
|
/* Data clocked out of eeprom on falling edge of clock */
|
|
|
|
rbyte = 0;
|
|
for (i=7, j=0; i>=0; i--)
|
|
{
|
|
NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE,
|
|
(val | clocktab[j++]) );
|
|
rbyte |= (((NICSTAR_REG_READ( base, NICSTAR_REG_GENERAL_PURPOSE)
|
|
& 0x00010000) >> 16) << i);
|
|
NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE,
|
|
(val | clocktab[j++]) );
|
|
osp_MicroDelay( CYCLE_DELAY );
|
|
}
|
|
NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE, 2 );
|
|
osp_MicroDelay( CYCLE_DELAY );
|
|
return rbyte;
|
|
}
|
|
#endif /* 0 */
|
|
|
|
|
|
/*
|
|
* This routine will clock the Read_data function into the X2520
|
|
* eeprom, followed by the address to read from, through the NicSTaR's General
|
|
* Purpose register.
|
|
*/
|
|
|
|
static u_int8_t
|
|
read_eprom_byte(virt_addr_t base, u_int8_t offset)
|
|
{
|
|
u_int32_t val = 0;
|
|
int i,j=0;
|
|
u_int8_t tempread = 0;
|
|
|
|
val = NICSTAR_REG_READ( base, NICSTAR_REG_GENERAL_PURPOSE ) & 0xFFFFFFF0;
|
|
|
|
/* Send READ instruction */
|
|
for (i=0; i<ARRAY_SIZE(readtab); i++)
|
|
{
|
|
NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE,
|
|
(val | readtab[i]) );
|
|
osp_MicroDelay( CYCLE_DELAY );
|
|
}
|
|
|
|
/* Next, we need to send the byte address to read from */
|
|
for (i=7; i>=0; i--)
|
|
{
|
|
NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE,
|
|
(val | clocktab[j++] | ((offset >> i) & 1) ) );
|
|
osp_MicroDelay(CYCLE_DELAY);
|
|
NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE,
|
|
(val | clocktab[j++] | ((offset >> i) & 1) ) );
|
|
osp_MicroDelay( CYCLE_DELAY );
|
|
}
|
|
|
|
j = 0;
|
|
|
|
/* Now, we can read data from the eeprom by clocking it in */
|
|
for (i=7; i>=0; i--)
|
|
{
|
|
NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE,
|
|
(val | clocktab[j++]) );
|
|
osp_MicroDelay( CYCLE_DELAY );
|
|
tempread |= (((NICSTAR_REG_READ( base, NICSTAR_REG_GENERAL_PURPOSE )
|
|
& 0x00010000) >> 16) << i);
|
|
NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE,
|
|
(val | clocktab[j++]) );
|
|
osp_MicroDelay( CYCLE_DELAY );
|
|
}
|
|
|
|
NICSTAR_REG_WRITE( base, NICSTAR_REG_GENERAL_PURPOSE, 2 );
|
|
osp_MicroDelay( CYCLE_DELAY );
|
|
return tempread;
|
|
}
|
|
|
|
|
|
static void
|
|
nicstar_init_eprom( virt_addr_t base )
|
|
{
|
|
u_int32_t val;
|
|
|
|
/*
|
|
* turn chip select off
|
|
*/
|
|
val = NICSTAR_REG_READ(base, NICSTAR_REG_GENERAL_PURPOSE) & 0xFFFFFFF0;
|
|
|
|
NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
|
|
(val | CS_HIGH | CLK_HIGH));
|
|
osp_MicroDelay( CYCLE_DELAY );
|
|
|
|
NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
|
|
(val | CS_HIGH | CLK_LOW));
|
|
osp_MicroDelay( CYCLE_DELAY );
|
|
|
|
NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
|
|
(val | CS_HIGH | CLK_HIGH));
|
|
osp_MicroDelay( CYCLE_DELAY );
|
|
|
|
NICSTAR_REG_WRITE(base, NICSTAR_REG_GENERAL_PURPOSE,
|
|
(val | CS_HIGH | CLK_LOW));
|
|
osp_MicroDelay( CYCLE_DELAY );
|
|
}
|
|
|
|
|
|
/*
|
|
* This routine will be the interface to the ReadPromByte function
|
|
* above.
|
|
*/
|
|
|
|
static void
|
|
nicstar_read_eprom(
|
|
virt_addr_t base,
|
|
u_int8_t prom_offset,
|
|
u_int8_t *buffer,
|
|
u_int32_t nbytes )
|
|
{
|
|
u_int i;
|
|
|
|
for (i=0; i<nbytes; i++)
|
|
{
|
|
buffer[i] = read_eprom_byte( base, prom_offset );
|
|
++prom_offset;
|
|
osp_MicroDelay( CYCLE_DELAY );
|
|
}
|
|
}
|
|
|
|
|
|
/*
|
|
void osp_MicroDelay(int x) {
|
|
|
|
}
|
|
*/
|
|
|
|
|