You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
120 lines
3.0 KiB
120 lines
3.0 KiB
/*
|
|
* arch/mips/ddb5074/int-handler.S -- NEC DDB Vrc-5074 interrupt handler
|
|
*
|
|
* Based on arch/mips/sgi/kernel/indyIRQ.S
|
|
*
|
|
* Copyright (C) 1996 David S. Miller (dm@engr.sgi.com)
|
|
*
|
|
* Copyright (C) 2000 Geert Uytterhoeven <geert@sonycom.com>
|
|
* Sony Software Development Center Europe (SDCE), Brussels
|
|
*/
|
|
#include <asm/asm.h>
|
|
#include <asm/mipsregs.h>
|
|
#include <asm/regdef.h>
|
|
#include <asm/stackframe.h>
|
|
|
|
/* A lot of complication here is taken away because:
|
|
*
|
|
* 1) We handle one interrupt and return, sitting in a loop and moving across
|
|
* all the pending IRQ bits in the cause register is _NOT_ the answer, the
|
|
* common case is one pending IRQ so optimize in that direction.
|
|
*
|
|
* 2) We need not check against bits in the status register IRQ mask, that
|
|
* would make this routine slow as hell.
|
|
*
|
|
* 3) Linux only thinks in terms of all IRQs on or all IRQs off, nothing in
|
|
* between like BSD spl() brain-damage.
|
|
*
|
|
* Furthermore, the IRQs on the INDY look basically (barring software IRQs
|
|
* which we don't use at all) like:
|
|
*
|
|
* MIPS IRQ Source
|
|
* -------- ------
|
|
* 0 Software (ignored)
|
|
* 1 Software (ignored)
|
|
* 2 Local IRQ level zero
|
|
* 3 Local IRQ level one
|
|
* 4 8254 Timer zero
|
|
* 5 8254 Timer one
|
|
* 6 Bus Error
|
|
* 7 R4k timer (what we use)
|
|
*
|
|
* We handle the IRQ according to _our_ priority which is:
|
|
*
|
|
* Highest ---- R4k Timer
|
|
* Local IRQ zero
|
|
* Local IRQ one
|
|
* Bus Error
|
|
* 8254 Timer zero
|
|
* Lowest ---- 8254 Timer one
|
|
*
|
|
* then we just return, if multiple IRQs are pending then we will just take
|
|
* another exception, big deal.
|
|
*/
|
|
|
|
.text
|
|
.set noreorder
|
|
.set noat
|
|
.align 5
|
|
NESTED(ddbIRQ, PT_SIZE, sp)
|
|
SAVE_ALL
|
|
CLI
|
|
.set at
|
|
mfc0 s0, CP0_CAUSE # get irq mask
|
|
|
|
#if 1
|
|
mfc0 t2,CP0_STATUS # get enabled interrupts
|
|
and s0,t2 # isolate allowed ones
|
|
#endif
|
|
/* First we check for r4k counter/timer IRQ. */
|
|
andi a0, s0, CAUSEF_IP2 # delay slot, check local level zero
|
|
beq a0, zero, 1f
|
|
andi a0, s0, CAUSEF_IP3 # delay slot, check local level one
|
|
|
|
/* Wheee, local level zero interrupt. */
|
|
jal ddb_local0_irqdispatch
|
|
move a0, sp # delay slot
|
|
|
|
j ret_from_irq
|
|
nop # delay slot
|
|
|
|
1:
|
|
beq a0, zero, 1f
|
|
andi a0, s0, CAUSEF_IP6 # delay slot, check bus error
|
|
|
|
/* Wheee, local level one interrupt. */
|
|
move a0, sp
|
|
jal ddb_local1_irqdispatch
|
|
nop
|
|
|
|
j ret_from_irq
|
|
nop
|
|
|
|
1:
|
|
beq a0, zero, 1f
|
|
nop
|
|
|
|
/* Wheee, an asynchronous bus error... */
|
|
move a0, sp
|
|
jal ddb_buserror_irq
|
|
nop
|
|
|
|
j ret_from_irq
|
|
nop
|
|
|
|
1:
|
|
/* Here by mistake? This is possible, what can happen
|
|
* is that by the time we take the exception the IRQ
|
|
* pin goes low, so just leave if this is the case.
|
|
*/
|
|
andi a0, s0, (CAUSEF_IP4 | CAUSEF_IP5)
|
|
beq a0, zero, 1f
|
|
|
|
/* Must be one of the 8254 timers... */
|
|
move a0, sp
|
|
jal ddb_8254timer_irq
|
|
nop
|
|
1:
|
|
j ret_from_irq
|
|
nop
|
|
END(ddbIRQ)
|
|
|