You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
581 lines
16 KiB
581 lines
16 KiB
/*
|
|
* linux/include/asm-arm/hardware/sa1111.h
|
|
*
|
|
* Copyright (C) 2000 John G Dorsey <john+@cs.cmu.edu>
|
|
*
|
|
* This file contains definitions for the SA-1111 Companion Chip.
|
|
* (Structure and naming borrowed from SA-1101.h, by Peter Danielsson.)
|
|
*
|
|
* Macro that calculates real address for registers in the SA-1111
|
|
*/
|
|
|
|
#ifndef _ASM_ARCH_SA1111
|
|
#define _ASM_ARCH_SA1111
|
|
|
|
#include <asm/arch/bitfield.h>
|
|
|
|
/*
|
|
* The SA1111 is always located at virtual 0xf4000000, and is always
|
|
* "native" endian.
|
|
*/
|
|
|
|
#define SA1111_VBASE 0xf4000000
|
|
|
|
/* Don't use these! */
|
|
#define SA1111_p2v( x ) ((x) - SA1111_BASE + SA1111_VBASE)
|
|
#define SA1111_v2p( x ) ((x) - SA1111_VBASE + SA1111_BASE)
|
|
|
|
#ifndef __ASSEMBLY__
|
|
#define _SA1111(x) ((x) + sa1111->resource.start)
|
|
#endif
|
|
|
|
#define sa1111_writel(val,addr) __raw_writel(val, addr)
|
|
#define sa1111_readl(addr) __raw_readl(addr)
|
|
|
|
/*
|
|
* 26 bits of the SA-1110 address bus are available to the SA-1111.
|
|
* Use these when feeding target addresses to the DMA engines.
|
|
*/
|
|
|
|
#define SA1111_ADDR_WIDTH (26)
|
|
#define SA1111_ADDR_MASK ((1<<SA1111_ADDR_WIDTH)-1)
|
|
#define SA1111_DMA_ADDR(x) ((x)&SA1111_ADDR_MASK)
|
|
|
|
/*
|
|
* Don't ask the (SAC) DMA engines to move less than this amount.
|
|
*/
|
|
|
|
#define SA1111_SAC_DMA_MIN_XFER (0x800)
|
|
|
|
/*
|
|
* System Bus Interface (SBI)
|
|
*
|
|
* Registers
|
|
* SKCR Control Register
|
|
* SMCR Shared Memory Controller Register
|
|
* SKID ID Register
|
|
*/
|
|
#define SA1111_SKCR 0x0000
|
|
#define SA1111_SMCR 0x0004
|
|
#define SA1111_SKID 0x0008
|
|
|
|
#define SKCR_PLL_BYPASS (1<<0)
|
|
#define SKCR_RCLKEN (1<<1)
|
|
#define SKCR_SLEEP (1<<2)
|
|
#define SKCR_DOZE (1<<3)
|
|
#define SKCR_VCO_OFF (1<<4)
|
|
#define SKCR_SCANTSTEN (1<<5)
|
|
#define SKCR_CLKTSTEN (1<<6)
|
|
#define SKCR_RDYEN (1<<7)
|
|
#define SKCR_SELAC (1<<8)
|
|
#define SKCR_OPPC (1<<9)
|
|
#define SKCR_PLLTSTEN (1<<10)
|
|
#define SKCR_USBIOTSTEN (1<<11)
|
|
/*
|
|
* Don't believe the specs! Take them, throw them outside. Leave them
|
|
* there for a week. Spit on them. Walk on them. Stamp on them.
|
|
* Pour gasoline over them and finally burn them. Now think about coding.
|
|
* - The October 1999 errata (278260-007) says its bit 13, 1 to enable.
|
|
* - The Feb 2001 errata (278260-010) says that the previous errata
|
|
* (278260-009) is wrong, and its bit actually 12, fixed in spec
|
|
* 278242-003.
|
|
* - The SA1111 manual (278242) says bit 12, but 0 to enable.
|
|
* - Reality is bit 13, 1 to enable.
|
|
* -- rmk
|
|
*/
|
|
#define SKCR_OE_EN (1<<13)
|
|
|
|
#define SMCR_DTIM (1<<0)
|
|
#define SMCR_MBGE (1<<1)
|
|
#define SMCR_DRAC_0 (1<<2)
|
|
#define SMCR_DRAC_1 (1<<3)
|
|
#define SMCR_DRAC_2 (1<<4)
|
|
#define SMCR_DRAC Fld(3, 2)
|
|
#define SMCR_CLAT (1<<5)
|
|
|
|
#define SKID_SIREV_MASK (0x000000f0)
|
|
#define SKID_MTREV_MASK (0x0000000f)
|
|
#define SKID_ID_MASK (0xffffff00)
|
|
#define SKID_SA1111_ID (0x690cc200)
|
|
|
|
/*
|
|
* System Controller
|
|
*
|
|
* Registers
|
|
* SKPCR Power Control Register
|
|
* SKCDR Clock Divider Register
|
|
* SKAUD Audio Clock Divider Register
|
|
* SKPMC PS/2 Mouse Clock Divider Register
|
|
* SKPTC PS/2 Track Pad Clock Divider Register
|
|
* SKPEN0 PWM0 Enable Register
|
|
* SKPWM0 PWM0 Clock Register
|
|
* SKPEN1 PWM1 Enable Register
|
|
* SKPWM1 PWM1 Clock Register
|
|
*/
|
|
#define SA1111_SKPCR 0x0200
|
|
#define SA1111_SKCDR 0x0204
|
|
#define SA1111_SKAUD 0x0208
|
|
#define SA1111_SKPMC 0x020c
|
|
#define SA1111_SKPTC 0x0210
|
|
#define SA1111_SKPEN0 0x0214
|
|
#define SA1111_SKPWM0 0x0218
|
|
#define SA1111_SKPEN1 0x021c
|
|
#define SA1111_SKPWM1 0x0220
|
|
|
|
#define SKPCR_UCLKEN (1<<0)
|
|
#define SKPCR_ACCLKEN (1<<1)
|
|
#define SKPCR_I2SCLKEN (1<<2)
|
|
#define SKPCR_L3CLKEN (1<<3)
|
|
#define SKPCR_SCLKEN (1<<4)
|
|
#define SKPCR_PMCLKEN (1<<5)
|
|
#define SKPCR_PTCLKEN (1<<6)
|
|
#define SKPCR_DCLKEN (1<<7)
|
|
#define SKPCR_PWMCLKEN (1<<8)
|
|
|
|
/*
|
|
* USB Host controller
|
|
*/
|
|
#define SA1111_USB 0x0400
|
|
|
|
/*
|
|
* Offsets from SA1111_USB_BASE
|
|
*/
|
|
#define SA1111_USB_STATUS 0x0118
|
|
#define SA1111_USB_RESET 0x011c
|
|
#define SA1111_USB_IRQTEST 0x0120
|
|
|
|
#define USB_RESET_FORCEIFRESET (1 << 0)
|
|
#define USB_RESET_FORCEHCRESET (1 << 1)
|
|
#define USB_RESET_CLKGENRESET (1 << 2)
|
|
#define USB_RESET_SIMSCALEDOWN (1 << 3)
|
|
#define USB_RESET_USBINTTEST (1 << 4)
|
|
#define USB_RESET_SLEEPSTBYEN (1 << 5)
|
|
#define USB_RESET_PWRSENSELOW (1 << 6)
|
|
#define USB_RESET_PWRCTRLLOW (1 << 7)
|
|
|
|
#define USB_STATUS_IRQHCIRMTWKUP (1 << 7)
|
|
#define USB_STATUS_IRQHCIBUFFACC (1 << 8)
|
|
#define USB_STATUS_NIRQHCIM (1 << 9)
|
|
#define USB_STATUS_NHCIMFCLR (1 << 10)
|
|
#define USB_STATUS_USBPWRSENSE (1 << 11)
|
|
|
|
/*
|
|
* Serial Audio Controller
|
|
*
|
|
* Registers
|
|
* SACR0 Serial Audio Common Control Register
|
|
* SACR1 Serial Audio Alternate Mode (I2C/MSB) Control Register
|
|
* SACR2 Serial Audio AC-link Control Register
|
|
* SASR0 Serial Audio I2S/MSB Interface & FIFO Status Register
|
|
* SASR1 Serial Audio AC-link Interface & FIFO Status Register
|
|
* SASCR Serial Audio Status Clear Register
|
|
* L3_CAR L3 Control Bus Address Register
|
|
* L3_CDR L3 Control Bus Data Register
|
|
* ACCAR AC-link Command Address Register
|
|
* ACCDR AC-link Command Data Register
|
|
* ACSAR AC-link Status Address Register
|
|
* ACSDR AC-link Status Data Register
|
|
* SADTCS Serial Audio DMA Transmit Control/Status Register
|
|
* SADTSA Serial Audio DMA Transmit Buffer Start Address A
|
|
* SADTCA Serial Audio DMA Transmit Buffer Count Register A
|
|
* SADTSB Serial Audio DMA Transmit Buffer Start Address B
|
|
* SADTCB Serial Audio DMA Transmit Buffer Count Register B
|
|
* SADRCS Serial Audio DMA Receive Control/Status Register
|
|
* SADRSA Serial Audio DMA Receive Buffer Start Address A
|
|
* SADRCA Serial Audio DMA Receive Buffer Count Register A
|
|
* SADRSB Serial Audio DMA Receive Buffer Start Address B
|
|
* SADRCB Serial Audio DMA Receive Buffer Count Register B
|
|
* SAITR Serial Audio Interrupt Test Register
|
|
* SADR Serial Audio Data Register (16 x 32-bit)
|
|
*/
|
|
|
|
#define SA1111_SERAUDIO 0x0600
|
|
|
|
/*
|
|
* These are offsets from the above base.
|
|
*/
|
|
#define SA1111_SACR0 0x00
|
|
#define SA1111_SACR1 0x04
|
|
#define SA1111_SACR2 0x08
|
|
#define SA1111_SASR0 0x0c
|
|
#define SA1111_SASR1 0x10
|
|
#define SA1111_SASCR 0x18
|
|
#define SA1111_L3_CAR 0x1c
|
|
#define SA1111_L3_CDR 0x20
|
|
#define SA1111_ACCAR 0x24
|
|
#define SA1111_ACCDR 0x28
|
|
#define SA1111_ACSAR 0x2c
|
|
#define SA1111_ACSDR 0x30
|
|
#define SA1111_SADTCS 0x34
|
|
#define SA1111_SADTSA 0x38
|
|
#define SA1111_SADTCA 0x3c
|
|
#define SA1111_SADTSB 0x40
|
|
#define SA1111_SADTCB 0x44
|
|
#define SA1111_SADRCS 0x48
|
|
#define SA1111_SADRSA 0x4c
|
|
#define SA1111_SADRCA 0x50
|
|
#define SA1111_SADRSB 0x54
|
|
#define SA1111_SADRCB 0x58
|
|
#define SA1111_SAITR 0x5c
|
|
#define SA1111_SADR 0x80
|
|
|
|
#ifndef CONFIG_ARCH_PXA
|
|
|
|
#define SACR0_ENB (1<<0)
|
|
#define SACR0_BCKD (1<<2)
|
|
#define SACR0_RST (1<<3)
|
|
|
|
#define SACR1_AMSL (1<<0)
|
|
#define SACR1_L3EN (1<<1)
|
|
#define SACR1_L3MB (1<<2)
|
|
#define SACR1_DREC (1<<3)
|
|
#define SACR1_DRPL (1<<4)
|
|
#define SACR1_ENLBF (1<<5)
|
|
|
|
#define SACR2_TS3V (1<<0)
|
|
#define SACR2_TS4V (1<<1)
|
|
#define SACR2_WKUP (1<<2)
|
|
#define SACR2_DREC (1<<3)
|
|
#define SACR2_DRPL (1<<4)
|
|
#define SACR2_ENLBF (1<<5)
|
|
#define SACR2_RESET (1<<6)
|
|
|
|
#define SASR0_TNF (1<<0)
|
|
#define SASR0_RNE (1<<1)
|
|
#define SASR0_BSY (1<<2)
|
|
#define SASR0_TFS (1<<3)
|
|
#define SASR0_RFS (1<<4)
|
|
#define SASR0_TUR (1<<5)
|
|
#define SASR0_ROR (1<<6)
|
|
#define SASR0_L3WD (1<<16)
|
|
#define SASR0_L3RD (1<<17)
|
|
|
|
#define SASR1_TNF (1<<0)
|
|
#define SASR1_RNE (1<<1)
|
|
#define SASR1_BSY (1<<2)
|
|
#define SASR1_TFS (1<<3)
|
|
#define SASR1_RFS (1<<4)
|
|
#define SASR1_TUR (1<<5)
|
|
#define SASR1_ROR (1<<6)
|
|
#define SASR1_CADT (1<<16)
|
|
#define SASR1_SADR (1<<17)
|
|
#define SASR1_RSTO (1<<18)
|
|
#define SASR1_CLPM (1<<19)
|
|
#define SASR1_CRDY (1<<20)
|
|
#define SASR1_RS3V (1<<21)
|
|
#define SASR1_RS4V (1<<22)
|
|
|
|
#define SASCR_TUR (1<<5)
|
|
#define SASCR_ROR (1<<6)
|
|
#define SASCR_DTS (1<<16)
|
|
#define SASCR_RDD (1<<17)
|
|
#define SASCR_STO (1<<18)
|
|
|
|
#define SADTCS_TDEN (1<<0)
|
|
#define SADTCS_TDIE (1<<1)
|
|
#define SADTCS_TDBDA (1<<3)
|
|
#define SADTCS_TDSTA (1<<4)
|
|
#define SADTCS_TDBDB (1<<5)
|
|
#define SADTCS_TDSTB (1<<6)
|
|
#define SADTCS_TBIU (1<<7)
|
|
|
|
#define SADRCS_RDEN (1<<0)
|
|
#define SADRCS_RDIE (1<<1)
|
|
#define SADRCS_RDBDA (1<<3)
|
|
#define SADRCS_RDSTA (1<<4)
|
|
#define SADRCS_RDBDB (1<<5)
|
|
#define SADRCS_RDSTB (1<<6)
|
|
#define SADRCS_RBIU (1<<7)
|
|
|
|
#define SAD_CS_DEN (1<<0)
|
|
#define SAD_CS_DIE (1<<1) /* Not functional on metal 1 */
|
|
#define SAD_CS_DBDA (1<<3) /* Not functional on metal 1 */
|
|
#define SAD_CS_DSTA (1<<4)
|
|
#define SAD_CS_DBDB (1<<5) /* Not functional on metal 1 */
|
|
#define SAD_CS_DSTB (1<<6)
|
|
#define SAD_CS_BIU (1<<7) /* Not functional on metal 1 */
|
|
|
|
#define SAITR_TFS (1<<0)
|
|
#define SAITR_RFS (1<<1)
|
|
#define SAITR_TUR (1<<2)
|
|
#define SAITR_ROR (1<<3)
|
|
#define SAITR_CADT (1<<4)
|
|
#define SAITR_SADR (1<<5)
|
|
#define SAITR_RSTO (1<<6)
|
|
#define SAITR_TDBDA (1<<8)
|
|
#define SAITR_TDBDB (1<<9)
|
|
#define SAITR_RDBDA (1<<10)
|
|
#define SAITR_RDBDB (1<<11)
|
|
|
|
#endif /* !CONFIG_ARCH_PXA */
|
|
|
|
/*
|
|
* General-Purpose I/O Interface
|
|
*
|
|
* Registers
|
|
* PA_DDR GPIO Block A Data Direction
|
|
* PA_DRR/PA_DWR GPIO Block A Data Value Register (read/write)
|
|
* PA_SDR GPIO Block A Sleep Direction
|
|
* PA_SSR GPIO Block A Sleep State
|
|
* PB_DDR GPIO Block B Data Direction
|
|
* PB_DRR/PB_DWR GPIO Block B Data Value Register (read/write)
|
|
* PB_SDR GPIO Block B Sleep Direction
|
|
* PB_SSR GPIO Block B Sleep State
|
|
* PC_DDR GPIO Block C Data Direction
|
|
* PC_DRR/PC_DWR GPIO Block C Data Value Register (read/write)
|
|
* PC_SDR GPIO Block C Sleep Direction
|
|
* PC_SSR GPIO Block C Sleep State
|
|
*/
|
|
|
|
#define _PA_DDR _SA1111( 0x1000 )
|
|
#define _PA_DRR _SA1111( 0x1004 )
|
|
#define _PA_DWR _SA1111( 0x1004 )
|
|
#define _PA_SDR _SA1111( 0x1008 )
|
|
#define _PA_SSR _SA1111( 0x100c )
|
|
#define _PB_DDR _SA1111( 0x1010 )
|
|
#define _PB_DRR _SA1111( 0x1014 )
|
|
#define _PB_DWR _SA1111( 0x1014 )
|
|
#define _PB_SDR _SA1111( 0x1018 )
|
|
#define _PB_SSR _SA1111( 0x101c )
|
|
#define _PC_DDR _SA1111( 0x1020 )
|
|
#define _PC_DRR _SA1111( 0x1024 )
|
|
#define _PC_DWR _SA1111( 0x1024 )
|
|
#define _PC_SDR _SA1111( 0x1028 )
|
|
#define _PC_SSR _SA1111( 0x102c )
|
|
|
|
#define SA1111_GPIO 0x1000
|
|
|
|
#define SA1111_GPIO_PADDR (0x000)
|
|
#define SA1111_GPIO_PADRR (0x004)
|
|
#define SA1111_GPIO_PADWR (0x004)
|
|
#define SA1111_GPIO_PASDR (0x008)
|
|
#define SA1111_GPIO_PASSR (0x00c)
|
|
#define SA1111_GPIO_PBDDR (0x010)
|
|
#define SA1111_GPIO_PBDRR (0x014)
|
|
#define SA1111_GPIO_PBDWR (0x014)
|
|
#define SA1111_GPIO_PBSDR (0x018)
|
|
#define SA1111_GPIO_PBSSR (0x01c)
|
|
#define SA1111_GPIO_PCDDR (0x020)
|
|
#define SA1111_GPIO_PCDRR (0x024)
|
|
#define SA1111_GPIO_PCDWR (0x024)
|
|
#define SA1111_GPIO_PCSDR (0x028)
|
|
#define SA1111_GPIO_PCSSR (0x02c)
|
|
|
|
#define GPIO_A0 (1 << 0)
|
|
#define GPIO_A1 (1 << 1)
|
|
#define GPIO_A2 (1 << 2)
|
|
#define GPIO_A3 (1 << 3)
|
|
|
|
#define GPIO_B0 (1 << 8)
|
|
#define GPIO_B1 (1 << 9)
|
|
#define GPIO_B2 (1 << 10)
|
|
#define GPIO_B3 (1 << 11)
|
|
#define GPIO_B4 (1 << 12)
|
|
#define GPIO_B5 (1 << 13)
|
|
#define GPIO_B6 (1 << 14)
|
|
#define GPIO_B7 (1 << 15)
|
|
|
|
#define GPIO_C0 (1 << 16)
|
|
#define GPIO_C1 (1 << 17)
|
|
#define GPIO_C2 (1 << 18)
|
|
#define GPIO_C3 (1 << 19)
|
|
#define GPIO_C4 (1 << 20)
|
|
#define GPIO_C5 (1 << 21)
|
|
#define GPIO_C6 (1 << 22)
|
|
#define GPIO_C7 (1 << 23)
|
|
|
|
/*
|
|
* Interrupt Controller
|
|
*
|
|
* Registers
|
|
* INTTEST0 Test register 0
|
|
* INTTEST1 Test register 1
|
|
* INTEN0 Interrupt Enable register 0
|
|
* INTEN1 Interrupt Enable register 1
|
|
* INTPOL0 Interrupt Polarity selection 0
|
|
* INTPOL1 Interrupt Polarity selection 1
|
|
* INTTSTSEL Interrupt source selection
|
|
* INTSTATCLR0 Interrupt Status/Clear 0
|
|
* INTSTATCLR1 Interrupt Status/Clear 1
|
|
* INTSET0 Interrupt source set 0
|
|
* INTSET1 Interrupt source set 1
|
|
* WAKE_EN0 Wake-up source enable 0
|
|
* WAKE_EN1 Wake-up source enable 1
|
|
* WAKE_POL0 Wake-up polarity selection 0
|
|
* WAKE_POL1 Wake-up polarity selection 1
|
|
*/
|
|
#define SA1111_INTC 0x1600
|
|
|
|
/*
|
|
* These are offsets from the above base.
|
|
*/
|
|
#define SA1111_INTTEST0 0x0000
|
|
#define SA1111_INTTEST1 0x0004
|
|
#define SA1111_INTEN0 0x0008
|
|
#define SA1111_INTEN1 0x000c
|
|
#define SA1111_INTPOL0 0x0010
|
|
#define SA1111_INTPOL1 0x0014
|
|
#define SA1111_INTTSTSEL 0x0018
|
|
#define SA1111_INTSTATCLR0 0x001c
|
|
#define SA1111_INTSTATCLR1 0x0020
|
|
#define SA1111_INTSET0 0x0024
|
|
#define SA1111_INTSET1 0x0028
|
|
#define SA1111_WAKEEN0 0x002c
|
|
#define SA1111_WAKEEN1 0x0030
|
|
#define SA1111_WAKEPOL0 0x0034
|
|
#define SA1111_WAKEPOL1 0x0038
|
|
|
|
/*
|
|
* PS/2 Trackpad and Mouse Interfaces
|
|
*
|
|
* Registers
|
|
* PS2CR Control Register
|
|
* PS2STAT Status Register
|
|
* PS2DATA Transmit/Receive Data register
|
|
* PS2CLKDIV Clock Division Register
|
|
* PS2PRECNT Clock Precount Register
|
|
* PS2TEST1 Test register 1
|
|
* PS2TEST2 Test register 2
|
|
* PS2TEST3 Test register 3
|
|
* PS2TEST4 Test register 4
|
|
*/
|
|
|
|
#define SA1111_KBD 0x0a00
|
|
#define SA1111_MSE 0x0c00
|
|
|
|
/*
|
|
* These are offsets from the above bases.
|
|
*/
|
|
#define SA1111_PS2CR 0x0000
|
|
#define SA1111_PS2STAT 0x0004
|
|
#define SA1111_PS2DATA 0x0008
|
|
#define SA1111_PS2CLKDIV 0x000c
|
|
#define SA1111_PS2PRECNT 0x0010
|
|
|
|
#define PS2CR_ENA 0x08
|
|
#define PS2CR_FKD 0x02
|
|
#define PS2CR_FKC 0x01
|
|
|
|
#define PS2STAT_STP 0x0100
|
|
#define PS2STAT_TXE 0x0080
|
|
#define PS2STAT_TXB 0x0040
|
|
#define PS2STAT_RXF 0x0020
|
|
#define PS2STAT_RXB 0x0010
|
|
#define PS2STAT_ENA 0x0008
|
|
#define PS2STAT_RXP 0x0004
|
|
#define PS2STAT_KBD 0x0002
|
|
#define PS2STAT_KBC 0x0001
|
|
|
|
/*
|
|
* PCMCIA Interface
|
|
*
|
|
* Registers
|
|
* PCSR Status Register
|
|
* PCCR Control Register
|
|
* PCSSR Sleep State Register
|
|
*/
|
|
|
|
#define SA1111_PCMCIA 0x1600
|
|
|
|
/*
|
|
* These are offsets from the above base.
|
|
*/
|
|
#define SA1111_PCCR 0x0000
|
|
#define SA1111_PCSSR 0x0004
|
|
#define SA1111_PCSR 0x0008
|
|
|
|
#define PCSR_S0_READY (1<<0)
|
|
#define PCSR_S1_READY (1<<1)
|
|
#define PCSR_S0_DETECT (1<<2)
|
|
#define PCSR_S1_DETECT (1<<3)
|
|
#define PCSR_S0_VS1 (1<<4)
|
|
#define PCSR_S0_VS2 (1<<5)
|
|
#define PCSR_S1_VS1 (1<<6)
|
|
#define PCSR_S1_VS2 (1<<7)
|
|
#define PCSR_S0_WP (1<<8)
|
|
#define PCSR_S1_WP (1<<9)
|
|
#define PCSR_S0_BVD1 (1<<10)
|
|
#define PCSR_S0_BVD2 (1<<11)
|
|
#define PCSR_S1_BVD1 (1<<12)
|
|
#define PCSR_S1_BVD2 (1<<13)
|
|
|
|
#define PCCR_S0_RST (1<<0)
|
|
#define PCCR_S1_RST (1<<1)
|
|
#define PCCR_S0_FLT (1<<2)
|
|
#define PCCR_S1_FLT (1<<3)
|
|
#define PCCR_S0_PWAITEN (1<<4)
|
|
#define PCCR_S1_PWAITEN (1<<5)
|
|
#define PCCR_S0_PSE (1<<6)
|
|
#define PCCR_S1_PSE (1<<7)
|
|
|
|
#define PCSSR_S0_SLEEP (1<<0)
|
|
#define PCSSR_S1_SLEEP (1<<1)
|
|
|
|
|
|
|
|
|
|
extern struct bus_type sa1111_bus_type;
|
|
|
|
#define SA1111_DEVID_SBI 0
|
|
#define SA1111_DEVID_SK 1
|
|
#define SA1111_DEVID_USB 2
|
|
#define SA1111_DEVID_SAC 3
|
|
#define SA1111_DEVID_SSP 4
|
|
#define SA1111_DEVID_PS2 5
|
|
#define SA1111_DEVID_GPIO 6
|
|
#define SA1111_DEVID_INT 7
|
|
#define SA1111_DEVID_PCMCIA 8
|
|
|
|
struct sa1111_dev {
|
|
struct device dev;
|
|
unsigned int devid;
|
|
struct resource res;
|
|
void __iomem *mapbase;
|
|
unsigned int skpcr_mask;
|
|
unsigned int irq[6];
|
|
u64 dma_mask;
|
|
};
|
|
|
|
#define SA1111_DEV(_d) container_of((_d), struct sa1111_dev, dev)
|
|
|
|
#define sa1111_get_drvdata(d) dev_get_drvdata(&(d)->dev)
|
|
#define sa1111_set_drvdata(d,p) dev_set_drvdata(&(d)->dev, p)
|
|
|
|
struct sa1111_driver {
|
|
struct device_driver drv;
|
|
unsigned int devid;
|
|
int (*probe)(struct sa1111_dev *);
|
|
int (*remove)(struct sa1111_dev *);
|
|
int (*suspend)(struct sa1111_dev *, pm_message_t);
|
|
int (*resume)(struct sa1111_dev *);
|
|
};
|
|
|
|
#define SA1111_DRV(_d) container_of((_d), struct sa1111_driver, drv)
|
|
|
|
#define SA1111_DRIVER_NAME(_sadev) ((_sadev)->dev.driver->name)
|
|
|
|
/*
|
|
* These frob the SKPCR register.
|
|
*/
|
|
void sa1111_enable_device(struct sa1111_dev *);
|
|
void sa1111_disable_device(struct sa1111_dev *);
|
|
|
|
unsigned int sa1111_pll_clock(struct sa1111_dev *);
|
|
|
|
#define SA1111_AUDIO_ACLINK 0
|
|
#define SA1111_AUDIO_I2S 1
|
|
|
|
void sa1111_select_audio_mode(struct sa1111_dev *sadev, int mode);
|
|
int sa1111_set_audio_rate(struct sa1111_dev *sadev, int rate);
|
|
int sa1111_get_audio_rate(struct sa1111_dev *sadev);
|
|
|
|
int sa1111_check_dma_bug(dma_addr_t addr);
|
|
|
|
int sa1111_driver_register(struct sa1111_driver *);
|
|
void sa1111_driver_unregister(struct sa1111_driver *);
|
|
|
|
void sa1111_set_io_dir(struct sa1111_dev *sadev, unsigned int bits, unsigned int dir, unsigned int sleep_dir);
|
|
void sa1111_set_io(struct sa1111_dev *sadev, unsigned int bits, unsigned int v);
|
|
void sa1111_set_sleep_io(struct sa1111_dev *sadev, unsigned int bits, unsigned int v);
|
|
|
|
#endif /* _ASM_ARCH_SA1111 */
|
|
|