You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
531 lines
13 KiB
531 lines
13 KiB
/*
|
|
* OHCI HCD (Host Controller Driver) for USB.
|
|
*
|
|
* (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
|
|
* (C) Copyright 2000-2005 David Brownell
|
|
* (C) Copyright 2002 Hewlett-Packard Company
|
|
*
|
|
* OMAP Bus Glue
|
|
*
|
|
* Modified for OMAP by Tony Lindgren <tony@atomide.com>
|
|
* Based on the 2.4 OMAP OHCI driver originally done by MontaVista Software Inc.
|
|
* and on ohci-sa1111.c by Christopher Hoover <ch@hpl.hp.com>
|
|
*
|
|
* This file is licenced under the GPL.
|
|
*/
|
|
|
|
#include <linux/signal.h> /* IRQF_DISABLED */
|
|
#include <linux/jiffies.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/clk.h>
|
|
|
|
#include <asm/hardware.h>
|
|
#include <asm/io.h>
|
|
#include <asm/mach-types.h>
|
|
|
|
#include <asm/arch/mux.h>
|
|
#include <asm/arch/irqs.h>
|
|
#include <asm/arch/gpio.h>
|
|
#include <asm/arch/fpga.h>
|
|
#include <asm/arch/usb.h>
|
|
|
|
|
|
/* OMAP-1510 OHCI has its own MMU for DMA */
|
|
#define OMAP1510_LB_MEMSIZE 32 /* Should be same as SDRAM size */
|
|
#define OMAP1510_LB_CLOCK_DIV 0xfffec10c
|
|
#define OMAP1510_LB_MMU_CTL 0xfffec208
|
|
#define OMAP1510_LB_MMU_LCK 0xfffec224
|
|
#define OMAP1510_LB_MMU_LD_TLB 0xfffec228
|
|
#define OMAP1510_LB_MMU_CAM_H 0xfffec22c
|
|
#define OMAP1510_LB_MMU_CAM_L 0xfffec230
|
|
#define OMAP1510_LB_MMU_RAM_H 0xfffec234
|
|
#define OMAP1510_LB_MMU_RAM_L 0xfffec238
|
|
|
|
|
|
#ifndef CONFIG_ARCH_OMAP
|
|
#error "This file is OMAP bus glue. CONFIG_OMAP must be defined."
|
|
#endif
|
|
|
|
#ifdef CONFIG_TPS65010
|
|
#include <asm/arch/tps65010.h>
|
|
#else
|
|
|
|
#define LOW 0
|
|
#define HIGH 1
|
|
|
|
#define GPIO1 1
|
|
|
|
static inline int tps65010_set_gpio_out_value(unsigned gpio, unsigned value)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
#endif
|
|
|
|
extern int usb_disabled(void);
|
|
extern int ocpi_enable(void);
|
|
|
|
static struct clk *usb_host_ck;
|
|
|
|
static void omap_ohci_clock_power(int on)
|
|
{
|
|
if (on) {
|
|
clk_enable(usb_host_ck);
|
|
/* guesstimate for T5 == 1x 32K clock + APLL lock time */
|
|
udelay(100);
|
|
} else {
|
|
clk_disable(usb_host_ck);
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Board specific gang-switched transceiver power on/off.
|
|
* NOTE: OSK supplies power from DC, not battery.
|
|
*/
|
|
static int omap_ohci_transceiver_power(int on)
|
|
{
|
|
if (on) {
|
|
if (machine_is_omap_innovator() && cpu_is_omap1510())
|
|
fpga_write(fpga_read(INNOVATOR_FPGA_CAM_USB_CONTROL)
|
|
| ((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
|
|
INNOVATOR_FPGA_CAM_USB_CONTROL);
|
|
else if (machine_is_omap_osk())
|
|
tps65010_set_gpio_out_value(GPIO1, LOW);
|
|
} else {
|
|
if (machine_is_omap_innovator() && cpu_is_omap1510())
|
|
fpga_write(fpga_read(INNOVATOR_FPGA_CAM_USB_CONTROL)
|
|
& ~((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
|
|
INNOVATOR_FPGA_CAM_USB_CONTROL);
|
|
else if (machine_is_omap_osk())
|
|
tps65010_set_gpio_out_value(GPIO1, HIGH);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* OMAP-1510 specific Local Bus clock on/off
|
|
*/
|
|
static int omap_1510_local_bus_power(int on)
|
|
{
|
|
if (on) {
|
|
omap_writel((1 << 1) | (1 << 0), OMAP1510_LB_MMU_CTL);
|
|
udelay(200);
|
|
} else {
|
|
omap_writel(0, OMAP1510_LB_MMU_CTL);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* OMAP-1510 specific Local Bus initialization
|
|
* NOTE: This assumes 32MB memory size in OMAP1510LB_MEMSIZE.
|
|
* See also arch/mach-omap/memory.h for __virt_to_dma() and
|
|
* __dma_to_virt() which need to match with the physical
|
|
* Local Bus address below.
|
|
*/
|
|
static int omap_1510_local_bus_init(void)
|
|
{
|
|
unsigned int tlb;
|
|
unsigned long lbaddr, physaddr;
|
|
|
|
omap_writel((omap_readl(OMAP1510_LB_CLOCK_DIV) & 0xfffffff8) | 0x4,
|
|
OMAP1510_LB_CLOCK_DIV);
|
|
|
|
/* Configure the Local Bus MMU table */
|
|
for (tlb = 0; tlb < OMAP1510_LB_MEMSIZE; tlb++) {
|
|
lbaddr = tlb * 0x00100000 + OMAP1510_LB_OFFSET;
|
|
physaddr = tlb * 0x00100000 + PHYS_OFFSET;
|
|
omap_writel((lbaddr & 0x0fffffff) >> 22, OMAP1510_LB_MMU_CAM_H);
|
|
omap_writel(((lbaddr & 0x003ffc00) >> 6) | 0xc,
|
|
OMAP1510_LB_MMU_CAM_L);
|
|
omap_writel(physaddr >> 16, OMAP1510_LB_MMU_RAM_H);
|
|
omap_writel((physaddr & 0x0000fc00) | 0x300, OMAP1510_LB_MMU_RAM_L);
|
|
omap_writel(tlb << 4, OMAP1510_LB_MMU_LCK);
|
|
omap_writel(0x1, OMAP1510_LB_MMU_LD_TLB);
|
|
}
|
|
|
|
/* Enable the walking table */
|
|
omap_writel(omap_readl(OMAP1510_LB_MMU_CTL) | (1 << 3), OMAP1510_LB_MMU_CTL);
|
|
udelay(200);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_USB_OTG
|
|
|
|
static void start_hnp(struct ohci_hcd *ohci)
|
|
{
|
|
const unsigned port = ohci_to_hcd(ohci)->self.otg_port - 1;
|
|
unsigned long flags;
|
|
|
|
otg_start_hnp(ohci->transceiver);
|
|
|
|
local_irq_save(flags);
|
|
ohci->transceiver->state = OTG_STATE_A_SUSPEND;
|
|
writel (RH_PS_PSS, &ohci->regs->roothub.portstatus [port]);
|
|
OTG_CTRL_REG &= ~OTG_A_BUSREQ;
|
|
local_irq_restore(flags);
|
|
}
|
|
|
|
#endif
|
|
|
|
/*-------------------------------------------------------------------------*/
|
|
|
|
static int omap_start_hc(struct ohci_hcd *ohci, struct platform_device *pdev)
|
|
{
|
|
struct omap_usb_config *config = pdev->dev.platform_data;
|
|
int need_transceiver = (config->otg != 0);
|
|
int ret;
|
|
|
|
dev_dbg(&pdev->dev, "starting USB Controller\n");
|
|
|
|
if (config->otg) {
|
|
ohci_to_hcd(ohci)->self.otg_port = config->otg;
|
|
/* default/minimum OTG power budget: 8 mA */
|
|
ohci_to_hcd(ohci)->power_budget = 8;
|
|
}
|
|
|
|
/* boards can use OTG transceivers in non-OTG modes */
|
|
need_transceiver = need_transceiver
|
|
|| machine_is_omap_h2() || machine_is_omap_h3();
|
|
|
|
if (cpu_is_omap16xx())
|
|
ocpi_enable();
|
|
|
|
#ifdef CONFIG_ARCH_OMAP_OTG
|
|
if (need_transceiver) {
|
|
ohci->transceiver = otg_get_transceiver();
|
|
if (ohci->transceiver) {
|
|
int status = otg_set_host(ohci->transceiver,
|
|
&ohci_to_hcd(ohci)->self);
|
|
dev_dbg(&pdev->dev, "init %s transceiver, status %d\n",
|
|
ohci->transceiver->label, status);
|
|
if (status) {
|
|
if (ohci->transceiver)
|
|
put_device(ohci->transceiver->dev);
|
|
return status;
|
|
}
|
|
} else {
|
|
dev_err(&pdev->dev, "can't find transceiver\n");
|
|
return -ENODEV;
|
|
}
|
|
}
|
|
#endif
|
|
|
|
omap_ohci_clock_power(1);
|
|
|
|
if (cpu_is_omap1510()) {
|
|
omap_1510_local_bus_power(1);
|
|
omap_1510_local_bus_init();
|
|
}
|
|
|
|
if ((ret = ohci_init(ohci)) < 0)
|
|
return ret;
|
|
|
|
/* board-specific power switching and overcurrent support */
|
|
if (machine_is_omap_osk() || machine_is_omap_innovator()) {
|
|
u32 rh = roothub_a (ohci);
|
|
|
|
/* power switching (ganged by default) */
|
|
rh &= ~RH_A_NPS;
|
|
|
|
/* TPS2045 switch for internal transceiver (port 1) */
|
|
if (machine_is_omap_osk()) {
|
|
ohci_to_hcd(ohci)->power_budget = 250;
|
|
|
|
rh &= ~RH_A_NOCP;
|
|
|
|
/* gpio9 for overcurrent detction */
|
|
omap_cfg_reg(W8_1610_GPIO9);
|
|
omap_request_gpio(9);
|
|
omap_set_gpio_direction(9, 1 /* IN */);
|
|
|
|
/* for paranoia's sake: disable USB.PUEN */
|
|
omap_cfg_reg(W4_USB_HIGHZ);
|
|
}
|
|
ohci_writel(ohci, rh, &ohci->regs->roothub.a);
|
|
distrust_firmware = 0;
|
|
}
|
|
|
|
/* FIXME khubd hub requests should manage power switching */
|
|
omap_ohci_transceiver_power(1);
|
|
|
|
/* board init will have already handled HMC and mux setup.
|
|
* any external transceiver should already be initialized
|
|
* too, so all configured ports use the right signaling now.
|
|
*/
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void omap_stop_hc(struct platform_device *pdev)
|
|
{
|
|
dev_dbg(&pdev->dev, "stopping USB Controller\n");
|
|
omap_ohci_clock_power(0);
|
|
}
|
|
|
|
|
|
/*-------------------------------------------------------------------------*/
|
|
|
|
void usb_hcd_omap_remove (struct usb_hcd *, struct platform_device *);
|
|
|
|
/* configure so an HC device and id are always provided */
|
|
/* always called with process context; sleeping is OK */
|
|
|
|
|
|
/**
|
|
* usb_hcd_omap_probe - initialize OMAP-based HCDs
|
|
* Context: !in_interrupt()
|
|
*
|
|
* Allocates basic resources for this USB host controller, and
|
|
* then invokes the start() method for the HCD associated with it
|
|
* through the hotplug entry's driver_data.
|
|
*/
|
|
int usb_hcd_omap_probe (const struct hc_driver *driver,
|
|
struct platform_device *pdev)
|
|
{
|
|
int retval, irq;
|
|
struct usb_hcd *hcd = 0;
|
|
struct ohci_hcd *ohci;
|
|
|
|
if (pdev->num_resources != 2) {
|
|
printk(KERN_ERR "hcd probe: invalid num_resources: %i\n",
|
|
pdev->num_resources);
|
|
return -ENODEV;
|
|
}
|
|
|
|
if (pdev->resource[0].flags != IORESOURCE_MEM
|
|
|| pdev->resource[1].flags != IORESOURCE_IRQ) {
|
|
printk(KERN_ERR "hcd probe: invalid resource type\n");
|
|
return -ENODEV;
|
|
}
|
|
|
|
usb_host_ck = clk_get(0, "usb_hhc_ck");
|
|
if (IS_ERR(usb_host_ck))
|
|
return PTR_ERR(usb_host_ck);
|
|
|
|
hcd = usb_create_hcd (driver, &pdev->dev, pdev->dev.bus_id);
|
|
if (!hcd) {
|
|
retval = -ENOMEM;
|
|
goto err0;
|
|
}
|
|
hcd->rsrc_start = pdev->resource[0].start;
|
|
hcd->rsrc_len = pdev->resource[0].end - pdev->resource[0].start + 1;
|
|
|
|
if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
|
|
dev_dbg(&pdev->dev, "request_mem_region failed\n");
|
|
retval = -EBUSY;
|
|
goto err1;
|
|
}
|
|
|
|
hcd->regs = (void __iomem *) (int) IO_ADDRESS(hcd->rsrc_start);
|
|
|
|
ohci = hcd_to_ohci(hcd);
|
|
ohci_hcd_init(ohci);
|
|
|
|
retval = omap_start_hc(ohci, pdev);
|
|
if (retval < 0)
|
|
goto err2;
|
|
|
|
irq = platform_get_irq(pdev, 0);
|
|
if (irq < 0) {
|
|
retval = -ENXIO;
|
|
goto err2;
|
|
}
|
|
retval = usb_add_hcd(hcd, irq, IRQF_DISABLED);
|
|
if (retval == 0)
|
|
return retval;
|
|
|
|
omap_stop_hc(pdev);
|
|
err2:
|
|
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
|
|
err1:
|
|
usb_put_hcd(hcd);
|
|
err0:
|
|
clk_put(usb_host_ck);
|
|
return retval;
|
|
}
|
|
|
|
|
|
/* may be called with controller, bus, and devices active */
|
|
|
|
/**
|
|
* usb_hcd_omap_remove - shutdown processing for OMAP-based HCDs
|
|
* @dev: USB Host Controller being removed
|
|
* Context: !in_interrupt()
|
|
*
|
|
* Reverses the effect of usb_hcd_omap_probe(), first invoking
|
|
* the HCD's stop() method. It is always called from a thread
|
|
* context, normally "rmmod", "apmd", or something similar.
|
|
*
|
|
*/
|
|
void usb_hcd_omap_remove (struct usb_hcd *hcd, struct platform_device *pdev)
|
|
{
|
|
usb_remove_hcd(hcd);
|
|
if (machine_is_omap_osk())
|
|
omap_free_gpio(9);
|
|
omap_stop_hc(pdev);
|
|
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
|
|
usb_put_hcd(hcd);
|
|
clk_put(usb_host_ck);
|
|
}
|
|
|
|
/*-------------------------------------------------------------------------*/
|
|
|
|
static int __devinit
|
|
ohci_omap_start (struct usb_hcd *hcd)
|
|
{
|
|
struct omap_usb_config *config;
|
|
struct ohci_hcd *ohci = hcd_to_ohci (hcd);
|
|
int ret;
|
|
|
|
config = hcd->self.controller->platform_data;
|
|
if (config->otg || config->rwc)
|
|
writel(OHCI_CTRL_RWC, &ohci->regs->control);
|
|
|
|
if ((ret = ohci_run (ohci)) < 0) {
|
|
dev_err(hcd->self.controller, "can't start\n");
|
|
ohci_stop (hcd);
|
|
return ret;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
/*-------------------------------------------------------------------------*/
|
|
|
|
static const struct hc_driver ohci_omap_hc_driver = {
|
|
.description = hcd_name,
|
|
.product_desc = "OMAP OHCI",
|
|
.hcd_priv_size = sizeof(struct ohci_hcd),
|
|
|
|
/*
|
|
* generic hardware linkage
|
|
*/
|
|
.irq = ohci_irq,
|
|
.flags = HCD_USB11 | HCD_MEMORY,
|
|
|
|
/*
|
|
* basic lifecycle operations
|
|
*/
|
|
.start = ohci_omap_start,
|
|
.stop = ohci_stop,
|
|
|
|
/*
|
|
* managing i/o requests and associated device resources
|
|
*/
|
|
.urb_enqueue = ohci_urb_enqueue,
|
|
.urb_dequeue = ohci_urb_dequeue,
|
|
.endpoint_disable = ohci_endpoint_disable,
|
|
|
|
/*
|
|
* scheduling support
|
|
*/
|
|
.get_frame_number = ohci_get_frame,
|
|
|
|
/*
|
|
* root hub support
|
|
*/
|
|
.hub_status_data = ohci_hub_status_data,
|
|
.hub_control = ohci_hub_control,
|
|
#ifdef CONFIG_PM
|
|
.bus_suspend = ohci_bus_suspend,
|
|
.bus_resume = ohci_bus_resume,
|
|
#endif
|
|
.start_port_reset = ohci_start_port_reset,
|
|
};
|
|
|
|
/*-------------------------------------------------------------------------*/
|
|
|
|
static int ohci_hcd_omap_drv_probe(struct platform_device *dev)
|
|
{
|
|
return usb_hcd_omap_probe(&ohci_omap_hc_driver, dev);
|
|
}
|
|
|
|
static int ohci_hcd_omap_drv_remove(struct platform_device *dev)
|
|
{
|
|
struct usb_hcd *hcd = platform_get_drvdata(dev);
|
|
struct ohci_hcd *ohci = hcd_to_ohci (hcd);
|
|
|
|
usb_hcd_omap_remove(hcd, dev);
|
|
if (ohci->transceiver) {
|
|
(void) otg_set_host(ohci->transceiver, 0);
|
|
put_device(ohci->transceiver->dev);
|
|
}
|
|
platform_set_drvdata(dev, NULL);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*-------------------------------------------------------------------------*/
|
|
|
|
#ifdef CONFIG_PM
|
|
|
|
static int ohci_omap_suspend(struct platform_device *dev, pm_message_t message)
|
|
{
|
|
struct ohci_hcd *ohci = hcd_to_ohci(platform_get_drvdata(dev));
|
|
|
|
if (time_before(jiffies, ohci->next_statechange))
|
|
msleep(5);
|
|
ohci->next_statechange = jiffies;
|
|
|
|
omap_ohci_clock_power(0);
|
|
ohci_to_hcd(ohci)->state = HC_STATE_SUSPENDED;
|
|
dev->power.power_state = PMSG_SUSPEND;
|
|
return 0;
|
|
}
|
|
|
|
static int ohci_omap_resume(struct platform_device *dev)
|
|
{
|
|
struct ohci_hcd *ohci = hcd_to_ohci(platform_get_drvdata(dev));
|
|
|
|
if (time_before(jiffies, ohci->next_statechange))
|
|
msleep(5);
|
|
ohci->next_statechange = jiffies;
|
|
|
|
omap_ohci_clock_power(1);
|
|
dev->power.power_state = PMSG_ON;
|
|
usb_hcd_resume_root_hub(dev_get_drvdata(dev));
|
|
return 0;
|
|
}
|
|
|
|
#endif
|
|
|
|
/*-------------------------------------------------------------------------*/
|
|
|
|
/*
|
|
* Driver definition to register with the OMAP bus
|
|
*/
|
|
static struct platform_driver ohci_hcd_omap_driver = {
|
|
.probe = ohci_hcd_omap_drv_probe,
|
|
.remove = ohci_hcd_omap_drv_remove,
|
|
#ifdef CONFIG_PM
|
|
.suspend = ohci_omap_suspend,
|
|
.resume = ohci_omap_resume,
|
|
#endif
|
|
.driver = {
|
|
.owner = THIS_MODULE,
|
|
.name = "ohci",
|
|
},
|
|
};
|
|
|
|
static int __init ohci_hcd_omap_init (void)
|
|
{
|
|
printk (KERN_DEBUG "%s: " DRIVER_INFO " (OMAP)\n", hcd_name);
|
|
if (usb_disabled())
|
|
return -ENODEV;
|
|
|
|
pr_debug("%s: block sizes: ed %Zd td %Zd\n", hcd_name,
|
|
sizeof (struct ed), sizeof (struct td));
|
|
|
|
return platform_driver_register(&ohci_hcd_omap_driver);
|
|
}
|
|
|
|
static void __exit ohci_hcd_omap_cleanup (void)
|
|
{
|
|
platform_driver_unregister(&ohci_hcd_omap_driver);
|
|
}
|
|
|
|
module_init (ohci_hcd_omap_init);
|
|
module_exit (ohci_hcd_omap_cleanup);
|
|
|