You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
2701 lines
66 KiB
2701 lines
66 KiB
/* Copyright (c) 2014-2015, 2020, The Linux Foundation. All rights reserved.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 and
|
|
* only version 2 as published by the Free Software Foundation.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*/
|
|
|
|
#define pr_fmt(fmt) "SMB358 %s: " fmt, __func__
|
|
#include <linux/i2c.h>
|
|
#include <linux/debugfs.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/errno.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/module.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/power_supply.h>
|
|
#include <linux/regulator/of_regulator.h>
|
|
#include <linux/regulator/machine.h>
|
|
#include <linux/regulator/consumer.h>
|
|
#include <linux/regulator/driver.h>
|
|
#include <linux/of.h>
|
|
#include <linux/of_gpio.h>
|
|
#include <linux/mutex.h>
|
|
#include <linux/iio/iio.h>
|
|
#include <linux/iio/consumer.h>
|
|
#include <dt-bindings/iio/qcom,spmi-vadc.h>
|
|
#include <linux/extcon.h>
|
|
|
|
#define _SMB358_MASK(BITS, POS) \
|
|
((unsigned char)(((1 << (BITS)) - 1) << (POS)))
|
|
#define SMB358_MASK(LEFT_BIT_POS, RIGHT_BIT_POS) \
|
|
_SMB358_MASK((LEFT_BIT_POS) - (RIGHT_BIT_POS) + 1, \
|
|
(RIGHT_BIT_POS))
|
|
|
|
/* Config/Control registers */
|
|
#define CHG_CURRENT_CTRL_REG 0x0
|
|
#define CHG_OTH_CURRENT_CTRL_REG 0x1
|
|
#define VARIOUS_FUNC_REG 0x2
|
|
#define VFLOAT_REG 0x3
|
|
#define CHG_CTRL_REG 0x4
|
|
#define STAT_AND_TIMER_CTRL_REG 0x5
|
|
#define CHG_PIN_EN_CTRL_REG 0x6
|
|
#define THERM_A_CTRL_REG 0x7
|
|
#define SYSOK_AND_USB3_REG 0x8
|
|
#define OTHER_CTRL_REG 0x9
|
|
#define FAULT_INT_REG 0xC
|
|
#define STATUS_INT_REG 0xD
|
|
|
|
/* Command registers */
|
|
#define CMD_A_REG 0x30
|
|
#define CMD_B_REG 0x31
|
|
|
|
/* IRQ status registers */
|
|
#define IRQ_A_REG 0x35
|
|
#define IRQ_B_REG 0x36
|
|
#define IRQ_C_REG 0x37
|
|
#define IRQ_D_REG 0x38
|
|
#define IRQ_E_REG 0x39
|
|
#define IRQ_F_REG 0x3A
|
|
|
|
/* Status registers */
|
|
#define STATUS_C_REG 0x3D
|
|
#define STATUS_D_REG 0x3E
|
|
#define STATUS_E_REG 0x3F
|
|
|
|
/* Config bits */
|
|
#define CHG_INHI_EN_MASK BIT(1)
|
|
#define CHG_INHI_EN_BIT BIT(1)
|
|
#define CMD_A_CHG_ENABLE_BIT BIT(1)
|
|
#define CMD_A_VOLATILE_W_PERM_BIT BIT(7)
|
|
#define CMD_A_CHG_SUSP_EN_BIT BIT(2)
|
|
#define CMD_A_CHG_SUSP_EN_MASK BIT(2)
|
|
#define CMD_A_OTG_ENABLE_BIT BIT(4)
|
|
#define CMD_A_OTG_ENABLE_MASK BIT(4)
|
|
#define CMD_B_CHG_HC_ENABLE_BIT BIT(0)
|
|
#define USB3_ENABLE_BIT BIT(5)
|
|
#define USB3_ENABLE_MASK BIT(5)
|
|
#define CMD_B_CHG_USB_500_900_ENABLE_BIT BIT(1)
|
|
#define CHG_CTRL_AUTO_RECHARGE_ENABLE_BIT 0x0
|
|
#define CHG_CTRL_CURR_TERM_END_CHG_BIT 0x0
|
|
#define CHG_CTRL_BATT_MISSING_DET_THERM_IO SMB358_MASK(5, 4)
|
|
#define CHG_CTRL_AUTO_RECHARGE_MASK BIT(7)
|
|
#define CHG_AUTO_RECHARGE_DIS_BIT BIT(7)
|
|
#define CHG_CTRL_CURR_TERM_END_MASK BIT(6)
|
|
#define CHG_CTRL_BATT_MISSING_DET_MASK SMB358_MASK(5, 4)
|
|
#define CHG_CTRL_APSD_EN_BIT BIT(2)
|
|
#define CHG_CTRL_APSD_EN_MASK BIT(2)
|
|
#define CHG_ITERM_MASK 0x07
|
|
#define CHG_PIN_CTRL_USBCS_REG_BIT 0x0
|
|
/* This is to select if use external pin EN to control CHG */
|
|
#define CHG_PIN_CTRL_CHG_EN_LOW_PIN_BIT SMB358_MASK(6, 5)
|
|
#define CHG_PIN_CTRL_CHG_EN_LOW_REG_BIT 0x0
|
|
#define CHG_PIN_CTRL_CHG_EN_MASK SMB358_MASK(6, 5)
|
|
|
|
#define CHG_LOW_BATT_THRESHOLD \
|
|
SMB358_MASK(3, 0)
|
|
#define CHG_PIN_CTRL_USBCS_REG_MASK BIT(4)
|
|
#define CHG_PIN_CTRL_APSD_IRQ_BIT BIT(1)
|
|
#define CHG_PIN_CTRL_APSD_IRQ_MASK BIT(1)
|
|
#define CHG_PIN_CTRL_CHG_ERR_IRQ_BIT BIT(2)
|
|
#define CHG_PIN_CTRL_CHG_ERR_IRQ_MASK BIT(2)
|
|
#define VARIOUS_FUNC_USB_SUSP_EN_REG_BIT BIT(6)
|
|
#define VARIOUS_FUNC_USB_SUSP_MASK BIT(6)
|
|
#define FAULT_INT_HOT_COLD_HARD_BIT BIT(7)
|
|
#define FAULT_INT_HOT_COLD_SOFT_BIT BIT(6)
|
|
#define FAULT_INT_INPUT_OV_BIT BIT(3)
|
|
#define FAULT_INT_INPUT_UV_BIT BIT(2)
|
|
#define FAULT_INT_AICL_COMPLETE_BIT BIT(1)
|
|
#define STATUS_INT_CHG_TIMEOUT_BIT BIT(7)
|
|
#define STATUS_INT_OTG_DETECT_BIT BIT(6)
|
|
#define STATUS_INT_BATT_OV_BIT BIT(5)
|
|
#define STATUS_INT_CHGING_BIT BIT(4)
|
|
#define STATUS_INT_CHG_INHI_BIT BIT(3)
|
|
#define STATUS_INT_INOK_BIT BIT(2)
|
|
#define STATUS_INT_MISSING_BATT_BIT BIT(1)
|
|
#define STATUS_INT_LOW_BATT_BIT BIT(0)
|
|
#define THERM_A_THERM_MONITOR_EN_BIT 0x0
|
|
#define THERM_A_THERM_MONITOR_EN_MASK BIT(4)
|
|
#define VFLOAT_MASK 0x3F
|
|
|
|
/* IRQ status bits */
|
|
#define IRQ_A_HOT_HARD_BIT BIT(6)
|
|
#define IRQ_A_COLD_HARD_BIT BIT(4)
|
|
#define IRQ_A_HOT_SOFT_BIT BIT(2)
|
|
#define IRQ_A_COLD_SOFT_BIT BIT(0)
|
|
#define IRQ_B_BATT_MISSING_BIT BIT(4)
|
|
#define IRQ_B_BATT_LOW_BIT BIT(2)
|
|
#define IRQ_B_BATT_OV_BIT BIT(6)
|
|
#define IRQ_B_PRE_FAST_CHG_BIT BIT(0)
|
|
#define IRQ_C_TAPER_CHG_BIT BIT(2)
|
|
#define IRQ_C_TERM_BIT BIT(0)
|
|
#define IRQ_C_INT_OVER_TEMP_BIT BIT(6)
|
|
#define IRQ_D_CHG_TIMEOUT_BIT (BIT(0) | BIT(2))
|
|
#define IRQ_D_AICL_DONE_BIT BIT(4)
|
|
#define IRQ_D_APSD_COMPLETE BIT(6)
|
|
#define IRQ_E_INPUT_UV_BIT BIT(0)
|
|
#define IRQ_E_INPUT_OV_BIT BIT(2)
|
|
#define IRQ_E_AFVC_ACTIVE BIT(4)
|
|
#define IRQ_F_OTG_VALID_BIT BIT(2)
|
|
#define IRQ_F_OTG_BATT_FAIL_BIT BIT(4)
|
|
#define IRQ_F_OTG_OC_BIT BIT(6)
|
|
#define IRQ_F_POWER_OK BIT(0)
|
|
|
|
/* Status bits */
|
|
#define STATUS_C_CHARGING_MASK SMB358_MASK(2, 1)
|
|
#define STATUS_C_FAST_CHARGING BIT(2)
|
|
#define STATUS_C_PRE_CHARGING BIT(1)
|
|
#define STATUS_C_TAPER_CHARGING SMB358_MASK(2, 1)
|
|
#define STATUS_C_CHG_ERR_STATUS_BIT BIT(6)
|
|
#define STATUS_C_CHG_ENABLE_STATUS_BIT BIT(0)
|
|
#define STATUS_C_CHG_HOLD_OFF_BIT BIT(3)
|
|
#define STATUS_D_CHARGING_PORT_MASK \
|
|
SMB358_MASK(3, 0)
|
|
#define STATUS_D_PORT_ACA_DOCK BIT(3)
|
|
#define STATUS_D_PORT_SDP BIT(2)
|
|
#define STATUS_D_PORT_DCP BIT(1)
|
|
#define STATUS_D_PORT_CDP BIT(0)
|
|
#define STATUS_D_PORT_OTHER SMB358_MASK(1, 0)
|
|
#define STATUS_D_PORT_ACA_A (BIT(2) | BIT(0))
|
|
#define STATUS_D_PORT_ACA_B SMB358_MASK(2, 1)
|
|
#define STATUS_D_PORT_ACA_C SMB358_MASK(2, 0)
|
|
|
|
/* constants */
|
|
#define USB2_MIN_CURRENT_MA 100
|
|
#define USB2_MAX_CURRENT_MA 500
|
|
#define USB3_MIN_CURRENT_MA 150
|
|
#define USB3_MAX_CURRENT_MA 900
|
|
#define DCP_MAX_CURRENT_MA 1500
|
|
#define AC_CHG_CURRENT_MASK 0x70
|
|
#define AC_CHG_CURRENT_SHIFT 4
|
|
#define SMB358_IRQ_REG_COUNT 6
|
|
#define SMB358_FAST_CHG_MIN_MA 200
|
|
#define SMB358_FAST_CHG_MAX_MA 2000
|
|
#define SMB358_FAST_CHG_SHIFT 5
|
|
#define SMB_FAST_CHG_CURRENT_MASK 0xE0
|
|
#define SMB358_DEFAULT_BATT_CAPACITY 50
|
|
#define SMB358_BATT_GOOD_THRE_2P5 0x1
|
|
|
|
enum {
|
|
USER = BIT(0),
|
|
THERMAL = BIT(1),
|
|
CURRENT = BIT(2),
|
|
SOC = BIT(3),
|
|
FAKE_BATTERY = BIT(4),
|
|
};
|
|
|
|
struct smb358_regulator {
|
|
struct regulator_desc rdesc;
|
|
struct regulator_dev *rdev;
|
|
};
|
|
|
|
static const unsigned int smb358_extcon_cable[] = {
|
|
EXTCON_USB,
|
|
EXTCON_USB_HOST,
|
|
EXTCON_CHG_USB_SDP,
|
|
EXTCON_CHG_USB_CDP,
|
|
EXTCON_CHG_USB_DCP,
|
|
EXTCON_CHG_USB_ACA,
|
|
EXTCON_NONE
|
|
};
|
|
|
|
struct smb358_iio {
|
|
struct iio_channel *batt_id_therm;
|
|
struct iio_channel *vbat_sns;
|
|
};
|
|
|
|
struct smb358_charger {
|
|
struct i2c_client *client;
|
|
struct device *dev;
|
|
|
|
bool inhibit_disabled;
|
|
bool recharge_disabled;
|
|
int recharge_mv;
|
|
bool iterm_disabled;
|
|
int iterm_ma;
|
|
int vfloat_mv;
|
|
int chg_valid_gpio;
|
|
int chg_valid_act_low;
|
|
int chg_present;
|
|
int fake_battery_soc;
|
|
bool chg_autonomous_mode;
|
|
bool disable_apsd;
|
|
bool battery_missing;
|
|
const char *bms_psy_name;
|
|
bool resume_completed;
|
|
bool irq_waiting;
|
|
struct smb358_iio iio;
|
|
bool bms_controlled_charging;
|
|
bool skip_usb_suspend_for_fake_battery;
|
|
struct mutex read_write_lock;
|
|
struct mutex path_suspend_lock;
|
|
struct mutex irq_complete;
|
|
u8 irq_cfg_mask[2];
|
|
int irq_gpio;
|
|
int charging_disabled;
|
|
int fastchg_current_max_ma;
|
|
unsigned int connected_rid;
|
|
|
|
/* debugfs related */
|
|
#if defined(CONFIG_DEBUG_FS)
|
|
struct dentry *debug_root;
|
|
u32 peek_poke_address;
|
|
#endif
|
|
/* status tracking */
|
|
bool batt_full;
|
|
bool batt_hot;
|
|
bool batt_cold;
|
|
bool batt_warm;
|
|
bool batt_cool;
|
|
int charging_disabled_status;
|
|
int usb_suspended;
|
|
|
|
/* psy */
|
|
struct power_supply_desc usb_psy_d;
|
|
struct power_supply *usb_psy;
|
|
struct power_supply *bms_psy;
|
|
struct power_supply_desc batt_psy_d;
|
|
struct power_supply *batt_psy;
|
|
int usb_psy_ma;
|
|
u8 usb_psy_health;
|
|
|
|
/* otg 5V regulator */
|
|
struct smb358_regulator otg_vreg;
|
|
|
|
/* pinctrl parameters */
|
|
const char *pinctrl_state_name;
|
|
struct pinctrl *smb_pinctrl;
|
|
|
|
/* i2c pull up regulator */
|
|
struct regulator *vcc_i2c;
|
|
struct extcon_dev *extcon;
|
|
u32 cable_id;
|
|
enum power_supply_type charger_type;
|
|
};
|
|
|
|
struct smb_irq_info {
|
|
const char *name;
|
|
int (*smb_irq)(struct smb358_charger *chip,
|
|
u8 rt_stat);
|
|
int high;
|
|
int low;
|
|
};
|
|
|
|
struct irq_handler_info {
|
|
u8 stat_reg;
|
|
u8 val;
|
|
u8 prev_val;
|
|
struct smb_irq_info irq_info[4];
|
|
};
|
|
|
|
static int chg_current[] = {
|
|
300, 500, 700, 1000, 1200, 1500, 1800, 2000,
|
|
};
|
|
|
|
static int fast_chg_current[] = {
|
|
200, 450, 600, 900, 1300, 1500, 1800, 2000,
|
|
};
|
|
|
|
/* add supplied to "bms" function */
|
|
static char *pm_batt_supplied_to[] = {
|
|
"bms",
|
|
};
|
|
|
|
static int __smb358_read_reg(struct smb358_charger *chip, u8 reg, u8 *val)
|
|
{
|
|
s32 ret;
|
|
|
|
ret = i2c_smbus_read_byte_data(chip->client, reg);
|
|
if (ret < 0) {
|
|
dev_err(chip->dev,
|
|
"i2c read fail: can't read from %02x: %d\n", reg, ret);
|
|
return ret;
|
|
}
|
|
|
|
*val = ret;
|
|
return 0;
|
|
}
|
|
|
|
static int __smb358_write_reg(struct smb358_charger *chip, int reg, u8 val)
|
|
{
|
|
s32 ret;
|
|
|
|
ret = i2c_smbus_write_byte_data(chip->client, reg, val);
|
|
if (ret < 0) {
|
|
dev_err(chip->dev,
|
|
"i2c write fail: can't write %02x to %02x: %d\n",
|
|
val, reg, ret);
|
|
return ret;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static int smb358_read_reg(struct smb358_charger *chip, int reg,
|
|
u8 *val)
|
|
{
|
|
int rc;
|
|
|
|
mutex_lock(&chip->read_write_lock);
|
|
rc = __smb358_read_reg(chip, reg, val);
|
|
mutex_unlock(&chip->read_write_lock);
|
|
|
|
return rc;
|
|
}
|
|
|
|
static int smb358_write_reg(struct smb358_charger *chip, int reg,
|
|
u8 val)
|
|
{
|
|
int rc;
|
|
|
|
mutex_lock(&chip->read_write_lock);
|
|
rc = __smb358_write_reg(chip, reg, val);
|
|
mutex_unlock(&chip->read_write_lock);
|
|
|
|
return rc;
|
|
}
|
|
|
|
static int smb358_masked_write(struct smb358_charger *chip, int reg,
|
|
u8 mask, u8 val)
|
|
{
|
|
s32 rc;
|
|
u8 temp;
|
|
|
|
mutex_lock(&chip->read_write_lock);
|
|
rc = __smb358_read_reg(chip, reg, &temp);
|
|
if (rc) {
|
|
dev_err(chip->dev,
|
|
"smb358_read_reg Failed: reg=%03X, rc=%d\n", reg, rc);
|
|
goto out;
|
|
}
|
|
temp &= ~mask;
|
|
temp |= val & mask;
|
|
rc = __smb358_write_reg(chip, reg, temp);
|
|
if (rc) {
|
|
dev_err(chip->dev,
|
|
"smb358_write Failed: reg=%03X, rc=%d\n", reg, rc);
|
|
}
|
|
out:
|
|
mutex_unlock(&chip->read_write_lock);
|
|
return rc;
|
|
}
|
|
|
|
static int smb358_enable_volatile_writes(struct smb358_charger *chip)
|
|
{
|
|
int rc;
|
|
|
|
rc = smb358_masked_write(chip, CMD_A_REG, CMD_A_VOLATILE_W_PERM_BIT,
|
|
CMD_A_VOLATILE_W_PERM_BIT);
|
|
if (rc)
|
|
dev_err(chip->dev, "Couldn't write VOLATILE_W_PERM_BIT rc=%d\n",
|
|
rc);
|
|
|
|
return rc;
|
|
}
|
|
|
|
static int smb358_fastchg_current_set(struct smb358_charger *chip,
|
|
unsigned int fastchg_current)
|
|
{
|
|
int i;
|
|
|
|
if ((fastchg_current < SMB358_FAST_CHG_MIN_MA) ||
|
|
(fastchg_current > SMB358_FAST_CHG_MAX_MA)) {
|
|
dev_dbg(chip->dev, "bad fastchg current mA=%d asked to set\n",
|
|
fastchg_current);
|
|
return -EINVAL;
|
|
}
|
|
|
|
for (i = ARRAY_SIZE(fast_chg_current) - 1; i >= 0; i--) {
|
|
if (fast_chg_current[i] <= fastchg_current)
|
|
break;
|
|
}
|
|
|
|
if (i < 0) {
|
|
dev_err(chip->dev, "Invalid current setting %dmA\n",
|
|
fastchg_current);
|
|
i = 0;
|
|
}
|
|
|
|
i = i << SMB358_FAST_CHG_SHIFT;
|
|
dev_dbg(chip->dev, "fastchg limit=%d setting %02x\n",
|
|
fastchg_current, i);
|
|
|
|
return smb358_masked_write(chip, CHG_CURRENT_CTRL_REG,
|
|
SMB_FAST_CHG_CURRENT_MASK, i);
|
|
}
|
|
|
|
#define MIN_FLOAT_MV 3500
|
|
#define MAX_FLOAT_MV 4500
|
|
#define VFLOAT_STEP_MV 20
|
|
#define VFLOAT_4350MV 4350
|
|
static int smb358_float_voltage_set(struct smb358_charger *chip, int vfloat_mv)
|
|
{
|
|
u8 temp;
|
|
|
|
if ((vfloat_mv < MIN_FLOAT_MV) || (vfloat_mv > MAX_FLOAT_MV)) {
|
|
dev_err(chip->dev, "bad float voltage mv =%d asked to set\n",
|
|
vfloat_mv);
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (vfloat_mv == VFLOAT_4350MV)
|
|
temp = 0x2B;
|
|
else if (vfloat_mv > VFLOAT_4350MV)
|
|
temp = (vfloat_mv - MIN_FLOAT_MV) / VFLOAT_STEP_MV + 1;
|
|
else
|
|
temp = (vfloat_mv - MIN_FLOAT_MV) / VFLOAT_STEP_MV;
|
|
|
|
return smb358_masked_write(chip, VFLOAT_REG, VFLOAT_MASK, temp);
|
|
}
|
|
|
|
#define CHG_ITERM_30MA 0x00
|
|
#define CHG_ITERM_40MA 0x01
|
|
#define CHG_ITERM_60MA 0x02
|
|
#define CHG_ITERM_80MA 0x03
|
|
#define CHG_ITERM_100MA 0x04
|
|
#define CHG_ITERM_125MA 0x05
|
|
#define CHG_ITERM_150MA 0x06
|
|
#define CHG_ITERM_200MA 0x07
|
|
static int smb358_term_current_set(struct smb358_charger *chip)
|
|
{
|
|
u8 reg = 0;
|
|
int rc;
|
|
|
|
if (chip->iterm_ma != -EINVAL) {
|
|
if (chip->iterm_disabled)
|
|
dev_err(chip->dev, "Error: Both iterm_disabled and iterm_ma set\n");
|
|
|
|
if (chip->iterm_ma <= 30)
|
|
reg = CHG_ITERM_30MA;
|
|
else if (chip->iterm_ma <= 40)
|
|
reg = CHG_ITERM_40MA;
|
|
else if (chip->iterm_ma <= 60)
|
|
reg = CHG_ITERM_60MA;
|
|
else if (chip->iterm_ma <= 80)
|
|
reg = CHG_ITERM_80MA;
|
|
else if (chip->iterm_ma <= 100)
|
|
reg = CHG_ITERM_100MA;
|
|
else if (chip->iterm_ma <= 125)
|
|
reg = CHG_ITERM_125MA;
|
|
else if (chip->iterm_ma <= 150)
|
|
reg = CHG_ITERM_150MA;
|
|
else
|
|
reg = CHG_ITERM_200MA;
|
|
|
|
rc = smb358_masked_write(chip, CHG_CURRENT_CTRL_REG,
|
|
CHG_ITERM_MASK, reg);
|
|
if (rc) {
|
|
dev_err(chip->dev,
|
|
"Couldn't set iterm rc = %d\n", rc);
|
|
return rc;
|
|
}
|
|
}
|
|
|
|
if (chip->iterm_disabled) {
|
|
rc = smb358_masked_write(chip, CHG_CTRL_REG,
|
|
CHG_CTRL_CURR_TERM_END_MASK,
|
|
CHG_CTRL_CURR_TERM_END_MASK);
|
|
if (rc) {
|
|
dev_err(chip->dev, "Couldn't set iterm rc = %d\n",
|
|
rc);
|
|
return rc;
|
|
}
|
|
} else {
|
|
rc = smb358_masked_write(chip, CHG_CTRL_REG,
|
|
CHG_CTRL_CURR_TERM_END_MASK, 0);
|
|
if (rc) {
|
|
dev_err(chip->dev,
|
|
"Couldn't enable iterm rc = %d\n", rc);
|
|
return rc;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
#define VFLT_300MV 0x0C
|
|
#define VFLT_200MV 0x08
|
|
#define VFLT_100MV 0x04
|
|
#define VFLT_50MV 0x00
|
|
#define VFLT_MASK 0x0C
|
|
static int smb358_recharge_and_inhibit_set(struct smb358_charger *chip)
|
|
{
|
|
u8 reg = 0;
|
|
int rc;
|
|
|
|
if (chip->recharge_disabled)
|
|
rc = smb358_masked_write(chip, CHG_CTRL_REG,
|
|
CHG_CTRL_AUTO_RECHARGE_MASK, CHG_AUTO_RECHARGE_DIS_BIT);
|
|
else
|
|
rc = smb358_masked_write(chip, CHG_CTRL_REG,
|
|
CHG_CTRL_AUTO_RECHARGE_MASK, 0x0);
|
|
if (rc) {
|
|
dev_err(chip->dev,
|
|
"Couldn't set auto recharge en reg rc = %d\n", rc);
|
|
}
|
|
|
|
if (chip->inhibit_disabled)
|
|
rc = smb358_masked_write(chip, CHG_OTH_CURRENT_CTRL_REG,
|
|
CHG_INHI_EN_MASK, 0x0);
|
|
else
|
|
rc = smb358_masked_write(chip, CHG_OTH_CURRENT_CTRL_REG,
|
|
CHG_INHI_EN_MASK, CHG_INHI_EN_BIT);
|
|
if (rc) {
|
|
dev_err(chip->dev,
|
|
"Couldn't set inhibit en reg rc = %d\n", rc);
|
|
}
|
|
|
|
if (chip->recharge_mv != -EINVAL) {
|
|
if (chip->recharge_mv <= 50)
|
|
reg = VFLT_50MV;
|
|
else if (chip->recharge_mv <= 100)
|
|
reg = VFLT_100MV;
|
|
else if (chip->recharge_mv <= 200)
|
|
reg = VFLT_200MV;
|
|
else
|
|
reg = VFLT_300MV;
|
|
|
|
rc = smb358_masked_write(chip, CHG_OTH_CURRENT_CTRL_REG,
|
|
VFLT_MASK, reg);
|
|
if (rc) {
|
|
dev_err(chip->dev,
|
|
"Couldn't set inhibit threshold rc = %d\n", rc);
|
|
return rc;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int smb358_chg_otg_regulator_enable(struct regulator_dev *rdev)
|
|
{
|
|
int rc = 0;
|
|
struct smb358_charger *chip = rdev_get_drvdata(rdev);
|
|
|
|
rc = smb358_masked_write(chip, CMD_A_REG, CMD_A_OTG_ENABLE_BIT,
|
|
CMD_A_OTG_ENABLE_BIT);
|
|
if (rc)
|
|
dev_err(chip->dev, "Couldn't enable OTG mode rc=%d, reg=%2x\n",
|
|
rc, CMD_A_REG);
|
|
return rc;
|
|
}
|
|
|
|
static int smb358_chg_otg_regulator_disable(struct regulator_dev *rdev)
|
|
{
|
|
int rc = 0;
|
|
struct smb358_charger *chip = rdev_get_drvdata(rdev);
|
|
|
|
rc = smb358_masked_write(chip, CMD_A_REG, CMD_A_OTG_ENABLE_BIT, 0);
|
|
if (rc)
|
|
dev_err(chip->dev, "Couldn't disable OTG mode rc=%d, reg=%2x\n",
|
|
rc, CMD_A_REG);
|
|
return rc;
|
|
}
|
|
|
|
static int smb358_chg_otg_regulator_is_enable(struct regulator_dev *rdev)
|
|
{
|
|
int rc = 0;
|
|
u8 reg = 0;
|
|
struct smb358_charger *chip = rdev_get_drvdata(rdev);
|
|
|
|
rc = smb358_read_reg(chip, CMD_A_REG, ®);
|
|
if (rc) {
|
|
dev_err(chip->dev,
|
|
"Couldn't read OTG enable bit rc=%d, reg=%2x\n",
|
|
rc, CMD_A_REG);
|
|
return rc;
|
|
}
|
|
|
|
return (reg & CMD_A_OTG_ENABLE_BIT) ? 1 : 0;
|
|
}
|
|
|
|
struct regulator_ops smb358_chg_otg_reg_ops = {
|
|
.enable = smb358_chg_otg_regulator_enable,
|
|
.disable = smb358_chg_otg_regulator_disable,
|
|
.is_enabled = smb358_chg_otg_regulator_is_enable,
|
|
};
|
|
|
|
static int smb358_regulator_init(struct smb358_charger *chip)
|
|
{
|
|
int rc = 0;
|
|
struct regulator_init_data *init_data;
|
|
struct regulator_config cfg = {};
|
|
|
|
chip->otg_vreg.rdesc.owner = THIS_MODULE;
|
|
chip->otg_vreg.rdesc.type = REGULATOR_VOLTAGE;
|
|
chip->otg_vreg.rdesc.ops = &smb358_chg_otg_reg_ops;
|
|
chip->otg_vreg.rdesc.name = chip->dev->of_node->name;
|
|
chip->otg_vreg.rdesc.of_match = chip->dev->of_node->name;
|
|
|
|
init_data = of_get_regulator_init_data(chip->dev,
|
|
chip->dev->of_node, &chip->otg_vreg.rdesc);
|
|
if (!init_data) {
|
|
dev_err(chip->dev, "Allocate memory failed\n");
|
|
return -ENOMEM;
|
|
}
|
|
|
|
cfg.dev = chip->dev;
|
|
cfg.init_data = init_data;
|
|
cfg.driver_data = chip;
|
|
cfg.of_node = chip->dev->of_node;
|
|
chip->otg_vreg.rdev =
|
|
devm_regulator_register(chip->dev,
|
|
&chip->otg_vreg.rdesc, &cfg);
|
|
|
|
if (IS_ERR(chip->otg_vreg.rdev)) {
|
|
rc = PTR_ERR(chip->otg_vreg.rdev);
|
|
chip->otg_vreg.rdev = NULL;
|
|
if (rc != -EPROBE_DEFER)
|
|
dev_err(chip->dev,
|
|
"OTG reg failed, rc=%d\n", rc);
|
|
}
|
|
|
|
return rc;
|
|
}
|
|
|
|
static int __smb358_path_suspend(struct smb358_charger *chip, bool suspend)
|
|
{
|
|
int rc;
|
|
|
|
rc = smb358_masked_write(chip, CMD_A_REG, CMD_A_CHG_SUSP_EN_MASK,
|
|
suspend ? CMD_A_CHG_SUSP_EN_BIT : 0);
|
|
if (rc < 0)
|
|
dev_err(chip->dev, "Couldn't set CMD_A reg, rc = %d\n", rc);
|
|
|
|
return rc;
|
|
}
|
|
|
|
static int smb358_path_suspend(struct smb358_charger *chip, int reason,
|
|
bool suspend)
|
|
{
|
|
int rc = 0;
|
|
int suspended;
|
|
|
|
mutex_lock(&chip->path_suspend_lock);
|
|
suspended = chip->usb_suspended;
|
|
|
|
if (suspend == false)
|
|
suspended &= ~reason;
|
|
else
|
|
suspended |= reason;
|
|
|
|
if (!chip->usb_suspended && suspended) {
|
|
rc = __smb358_path_suspend(chip, true);
|
|
chip->usb_suspended = suspended;
|
|
power_supply_changed(chip->usb_psy);
|
|
} else if (chip->usb_suspended && !suspended) {
|
|
rc = __smb358_path_suspend(chip, false);
|
|
chip->usb_suspended = suspended;
|
|
power_supply_changed(chip->usb_psy);
|
|
}
|
|
|
|
if (rc)
|
|
dev_err(chip->dev, "Couldn't set/unset suspend rc = %d\n", rc);
|
|
|
|
mutex_unlock(&chip->path_suspend_lock);
|
|
|
|
return rc;
|
|
}
|
|
|
|
|
|
static int __smb358_charging_disable(struct smb358_charger *chip, bool disable)
|
|
{
|
|
int rc;
|
|
|
|
rc = smb358_masked_write(chip, CMD_A_REG, CMD_A_CHG_ENABLE_BIT,
|
|
disable ? 0 : CMD_A_CHG_ENABLE_BIT);
|
|
if (rc < 0)
|
|
pr_err("Couldn't set CHG_ENABLE_BIT disable = %d, rc = %d\n",
|
|
disable, rc);
|
|
return rc;
|
|
}
|
|
|
|
static int smb358_charging_disable(struct smb358_charger *chip,
|
|
int reason, int disable)
|
|
{
|
|
int rc = 0;
|
|
int disabled;
|
|
|
|
disabled = chip->charging_disabled_status;
|
|
|
|
pr_debug("reason = %d requested_disable = %d disabled_status = %d\n",
|
|
reason, disable, disabled);
|
|
|
|
if (disable == true)
|
|
disabled |= reason;
|
|
else
|
|
disabled &= ~reason;
|
|
|
|
if (!!disabled == !!chip->charging_disabled_status)
|
|
goto skip;
|
|
|
|
rc = __smb358_charging_disable(chip, !!disabled);
|
|
if (rc) {
|
|
pr_err("Failed to disable charging rc = %d\n", rc);
|
|
return rc;
|
|
}
|
|
|
|
/* will not modify online status in this condition */
|
|
power_supply_changed(chip->batt_psy);
|
|
|
|
skip:
|
|
chip->charging_disabled_status = disabled;
|
|
return rc;
|
|
}
|
|
|
|
#define MAX_INV_BATT_ID 7700
|
|
#define MIN_INV_BATT_ID 7300
|
|
static int smb358_hw_init(struct smb358_charger *chip)
|
|
{
|
|
int rc;
|
|
u8 reg = 0, mask = 0;
|
|
|
|
/* configure smb_pinctrl to enable irqs */
|
|
if (chip->pinctrl_state_name) {
|
|
chip->smb_pinctrl = pinctrl_get_select(chip->dev,
|
|
chip->pinctrl_state_name);
|
|
if (IS_ERR(chip->smb_pinctrl)) {
|
|
pr_err("Could not get/set %s pinctrl state rc = %ld\n",
|
|
chip->pinctrl_state_name,
|
|
PTR_ERR(chip->smb_pinctrl));
|
|
return PTR_ERR(chip->smb_pinctrl);
|
|
}
|
|
}
|
|
|
|
/*
|
|
* If the charger is pre-configured for autonomous operation,
|
|
* do not apply additional settings
|
|
*/
|
|
if (chip->chg_autonomous_mode) {
|
|
dev_dbg(chip->dev, "Charger configured for autonomous mode\n");
|
|
return 0;
|
|
}
|
|
|
|
rc = smb358_enable_volatile_writes(chip);
|
|
if (rc) {
|
|
dev_err(chip->dev, "Couldn't configure volatile writes rc=%d\n",
|
|
rc);
|
|
return rc;
|
|
}
|
|
|
|
/* setup defaults for CHG_CNTRL_REG */
|
|
reg = CHG_CTRL_BATT_MISSING_DET_THERM_IO;
|
|
mask = CHG_CTRL_BATT_MISSING_DET_MASK;
|
|
rc = smb358_masked_write(chip, CHG_CTRL_REG, mask, reg);
|
|
if (rc) {
|
|
dev_err(chip->dev, "Couldn't set CHG_CTRL_REG rc=%d\n", rc);
|
|
return rc;
|
|
}
|
|
/* setup defaults for PIN_CTRL_REG */
|
|
reg = CHG_PIN_CTRL_USBCS_REG_BIT | CHG_PIN_CTRL_CHG_EN_LOW_REG_BIT |
|
|
CHG_PIN_CTRL_APSD_IRQ_BIT | CHG_PIN_CTRL_CHG_ERR_IRQ_BIT;
|
|
mask = CHG_PIN_CTRL_CHG_EN_MASK | CHG_PIN_CTRL_USBCS_REG_MASK |
|
|
CHG_PIN_CTRL_APSD_IRQ_MASK | CHG_PIN_CTRL_CHG_ERR_IRQ_MASK;
|
|
rc = smb358_masked_write(chip, CHG_PIN_EN_CTRL_REG, mask, reg);
|
|
if (rc) {
|
|
dev_err(chip->dev, "Couldn't set CHG_PIN_EN_CTRL_REG rc=%d\n",
|
|
rc);
|
|
return rc;
|
|
}
|
|
|
|
/* setup USB suspend and APSD */
|
|
rc = smb358_masked_write(chip, VARIOUS_FUNC_REG,
|
|
VARIOUS_FUNC_USB_SUSP_MASK, VARIOUS_FUNC_USB_SUSP_EN_REG_BIT);
|
|
if (rc) {
|
|
dev_err(chip->dev, "Couldn't set VARIOUS_FUNC_REG rc=%d\n",
|
|
rc);
|
|
return rc;
|
|
}
|
|
|
|
if (!chip->disable_apsd)
|
|
reg = CHG_CTRL_APSD_EN_BIT;
|
|
else
|
|
reg = 0;
|
|
|
|
rc = smb358_masked_write(chip, CHG_CTRL_REG,
|
|
CHG_CTRL_APSD_EN_MASK, reg);
|
|
if (rc) {
|
|
dev_err(chip->dev, "Couldn't set CHG_CTRL_REG rc=%d\n",
|
|
rc);
|
|
return rc;
|
|
}
|
|
/* Fault and Status IRQ configuration */
|
|
reg = FAULT_INT_HOT_COLD_HARD_BIT | FAULT_INT_HOT_COLD_SOFT_BIT
|
|
| FAULT_INT_INPUT_UV_BIT | FAULT_INT_AICL_COMPLETE_BIT
|
|
| FAULT_INT_INPUT_OV_BIT;
|
|
rc = smb358_write_reg(chip, FAULT_INT_REG, reg);
|
|
if (rc) {
|
|
dev_err(chip->dev, "Couldn't set FAULT_INT_REG rc=%d\n", rc);
|
|
return rc;
|
|
}
|
|
reg = STATUS_INT_CHG_TIMEOUT_BIT | STATUS_INT_OTG_DETECT_BIT |
|
|
STATUS_INT_BATT_OV_BIT | STATUS_INT_CHGING_BIT |
|
|
STATUS_INT_CHG_INHI_BIT | STATUS_INT_INOK_BIT |
|
|
STATUS_INT_LOW_BATT_BIT | STATUS_INT_MISSING_BATT_BIT;
|
|
rc = smb358_write_reg(chip, STATUS_INT_REG, reg);
|
|
if (rc) {
|
|
dev_err(chip->dev, "Couldn't set STATUS_INT_REG rc=%d\n", rc);
|
|
return rc;
|
|
}
|
|
/* setup THERM Monitor */
|
|
rc = smb358_masked_write(chip, THERM_A_CTRL_REG,
|
|
THERM_A_THERM_MONITOR_EN_MASK, THERM_A_THERM_MONITOR_EN_BIT);
|
|
if (rc) {
|
|
dev_err(chip->dev, "Couldn't set THERM_A_CTRL_REG rc=%d\n",
|
|
rc);
|
|
return rc;
|
|
}
|
|
/* set the fast charge current limit */
|
|
rc = smb358_fastchg_current_set(chip, chip->fastchg_current_max_ma);
|
|
if (rc) {
|
|
dev_err(chip->dev, "Couldn't set fastchg current rc=%d\n", rc);
|
|
return rc;
|
|
}
|
|
|
|
/* set the float voltage */
|
|
rc = smb358_float_voltage_set(chip, chip->vfloat_mv);
|
|
if (rc < 0) {
|
|
dev_err(chip->dev,
|
|
"Couldn't set float voltage rc = %d\n", rc);
|
|
return rc;
|
|
}
|
|
|
|
/* set iterm */
|
|
rc = smb358_term_current_set(chip);
|
|
if (rc)
|
|
dev_err(chip->dev, "Couldn't set term current rc=%d\n", rc);
|
|
|
|
/* set recharge */
|
|
rc = smb358_recharge_and_inhibit_set(chip);
|
|
if (rc)
|
|
dev_err(chip->dev, "Couldn't set recharge para rc=%d\n", rc);
|
|
|
|
/* suspend USB path for fake battery */
|
|
if (!chip->skip_usb_suspend_for_fake_battery) {
|
|
if ((chip->connected_rid >= MIN_INV_BATT_ID) &&
|
|
(chip->connected_rid <= MAX_INV_BATT_ID)) {
|
|
rc = smb358_path_suspend(chip, FAKE_BATTERY, true);
|
|
if (!rc)
|
|
dev_info(chip->dev,
|
|
"Suspended USB path reason FAKE_BATTERY\n");
|
|
}
|
|
}
|
|
|
|
/* enable/disable charging */
|
|
if (chip->charging_disabled) {
|
|
rc = smb358_charging_disable(chip, USER, 1);
|
|
if (rc)
|
|
dev_err(chip->dev, "Couldn't '%s' charging rc = %d\n",
|
|
chip->charging_disabled ? "disable" : "enable", rc);
|
|
} else {
|
|
/*
|
|
* Enable charging explicitly,
|
|
* because not sure the default behavior.
|
|
*/
|
|
rc = __smb358_charging_disable(chip, 0);
|
|
if (rc)
|
|
dev_err(chip->dev, "Couldn't enable charging\n");
|
|
}
|
|
|
|
/*
|
|
* Workaround for recharge frequent issue: When battery is
|
|
* greater than 4.2v, and charging is disabled, charger
|
|
* stops switching. In such a case, system load is provided
|
|
* by battery rather than input, even though input is still
|
|
* there. Make reg09[0:3] to be a non-zero value which can
|
|
* keep the switcher active
|
|
*/
|
|
rc = smb358_masked_write(chip, OTHER_CTRL_REG, CHG_LOW_BATT_THRESHOLD,
|
|
SMB358_BATT_GOOD_THRE_2P5);
|
|
if (rc)
|
|
dev_err(chip->dev, "Couldn't write OTHER_CTRL_REG, rc = %d\n",
|
|
rc);
|
|
|
|
return rc;
|
|
}
|
|
|
|
static enum power_supply_property smb358_battery_properties[] = {
|
|
POWER_SUPPLY_PROP_STATUS,
|
|
POWER_SUPPLY_PROP_PRESENT,
|
|
POWER_SUPPLY_PROP_CHARGING_ENABLED,
|
|
POWER_SUPPLY_PROP_CHARGE_TYPE,
|
|
POWER_SUPPLY_PROP_CAPACITY,
|
|
POWER_SUPPLY_PROP_HEALTH,
|
|
POWER_SUPPLY_PROP_TECHNOLOGY,
|
|
POWER_SUPPLY_PROP_MODEL_NAME,
|
|
POWER_SUPPLY_PROP_TEMP,
|
|
POWER_SUPPLY_PROP_VOLTAGE_NOW,
|
|
};
|
|
|
|
static int smb358_get_prop_batt_status(struct smb358_charger *chip)
|
|
{
|
|
int rc;
|
|
u8 reg = 0;
|
|
|
|
if (chip->batt_full)
|
|
return POWER_SUPPLY_STATUS_FULL;
|
|
|
|
rc = smb358_read_reg(chip, STATUS_C_REG, ®);
|
|
if (rc) {
|
|
dev_err(chip->dev, "Couldn't read STAT_C rc = %d\n", rc);
|
|
return POWER_SUPPLY_STATUS_UNKNOWN;
|
|
}
|
|
|
|
dev_dbg(chip->dev, "%s: STATUS_C_REG=%x\n", __func__, reg);
|
|
|
|
if (reg & STATUS_C_CHG_HOLD_OFF_BIT)
|
|
return POWER_SUPPLY_STATUS_NOT_CHARGING;
|
|
|
|
if ((reg & STATUS_C_CHARGING_MASK) &&
|
|
!(reg & STATUS_C_CHG_ERR_STATUS_BIT))
|
|
return POWER_SUPPLY_STATUS_CHARGING;
|
|
|
|
return POWER_SUPPLY_STATUS_DISCHARGING;
|
|
}
|
|
|
|
static int smb358_get_prop_batt_present(struct smb358_charger *chip)
|
|
{
|
|
return !chip->battery_missing;
|
|
}
|
|
|
|
static int smb358_get_prop_batt_capacity(struct smb358_charger *chip)
|
|
{
|
|
union power_supply_propval ret = {0, };
|
|
|
|
if (chip->fake_battery_soc >= 0)
|
|
return chip->fake_battery_soc;
|
|
|
|
if (chip->bms_psy) {
|
|
power_supply_get_property(chip->bms_psy,
|
|
POWER_SUPPLY_PROP_CAPACITY, &ret);
|
|
return ret.intval;
|
|
}
|
|
|
|
pr_debug("return default capacity\n");
|
|
return SMB358_DEFAULT_BATT_CAPACITY;
|
|
}
|
|
|
|
static int smb358_get_prop_charge_type(struct smb358_charger *chip)
|
|
{
|
|
int rc;
|
|
u8 reg = 0;
|
|
|
|
rc = smb358_read_reg(chip, STATUS_C_REG, ®);
|
|
if (rc) {
|
|
dev_err(chip->dev, "Couldn't read STAT_C rc = %d\n", rc);
|
|
return POWER_SUPPLY_CHARGE_TYPE_UNKNOWN;
|
|
}
|
|
|
|
dev_dbg(chip->dev, "%s: STATUS_C_REG=%x\n", __func__, reg);
|
|
|
|
reg &= STATUS_C_CHARGING_MASK;
|
|
|
|
if (reg == STATUS_C_FAST_CHARGING)
|
|
return POWER_SUPPLY_CHARGE_TYPE_FAST;
|
|
else if (reg == STATUS_C_TAPER_CHARGING)
|
|
return POWER_SUPPLY_CHARGE_TYPE_TAPER;
|
|
else if (reg == STATUS_C_PRE_CHARGING)
|
|
return POWER_SUPPLY_CHARGE_TYPE_TRICKLE;
|
|
else
|
|
return POWER_SUPPLY_CHARGE_TYPE_NONE;
|
|
}
|
|
|
|
static int smb358_get_prop_batt_health(struct smb358_charger *chip)
|
|
{
|
|
union power_supply_propval ret = {0, };
|
|
|
|
if (chip->batt_hot)
|
|
ret.intval = POWER_SUPPLY_HEALTH_OVERHEAT;
|
|
else if (chip->batt_cold)
|
|
ret.intval = POWER_SUPPLY_HEALTH_COLD;
|
|
else if (chip->batt_warm)
|
|
ret.intval = POWER_SUPPLY_HEALTH_WARM;
|
|
else if (chip->batt_cool)
|
|
ret.intval = POWER_SUPPLY_HEALTH_COOL;
|
|
else
|
|
ret.intval = POWER_SUPPLY_HEALTH_GOOD;
|
|
|
|
return ret.intval;
|
|
}
|
|
|
|
#define DEFAULT_TEMP 250
|
|
static int smb358_get_prop_batt_temp(struct smb358_charger *chip)
|
|
{
|
|
union power_supply_propval ret = {0, };
|
|
|
|
if (chip->bms_psy) {
|
|
power_supply_get_property(chip->bms_psy,
|
|
POWER_SUPPLY_PROP_TEMP, &ret);
|
|
return ret.intval;
|
|
}
|
|
|
|
pr_debug("return default temperature\n");
|
|
return DEFAULT_TEMP;
|
|
}
|
|
|
|
|
|
static int
|
|
smb358_get_prop_battery_voltage_now(struct smb358_charger *chip)
|
|
{
|
|
int vbat_sns_result = 0;
|
|
int rc = 0;
|
|
|
|
if (chip->iio.vbat_sns) {
|
|
rc = iio_read_channel_processed(chip->iio.vbat_sns,
|
|
&vbat_sns_result);
|
|
if (rc < 0) {
|
|
pr_err("Unable to read vbat, rc = %d\n", rc);
|
|
return 0;
|
|
}
|
|
}
|
|
return vbat_sns_result;
|
|
}
|
|
|
|
static int smb358_get_iio_channel(struct smb358_charger *chip,
|
|
const char *propname, struct iio_channel **chan)
|
|
{
|
|
int rc = 0;
|
|
|
|
rc = of_property_match_string(chip->dev->of_node,
|
|
"io-channel-names", propname);
|
|
if (rc < 0)
|
|
return 0;
|
|
|
|
*chan = iio_channel_get(chip->dev, propname);
|
|
if (IS_ERR(*chan)) {
|
|
rc = PTR_ERR(*chan);
|
|
if (rc != -EPROBE_DEFER)
|
|
pr_err("%s channel unavailable, %d\n",
|
|
propname, rc);
|
|
*chan = NULL;
|
|
}
|
|
|
|
return rc;
|
|
}
|
|
|
|
static int smb358_set_usb_chg_current(struct smb358_charger *chip,
|
|
int current_ma)
|
|
{
|
|
int i, rc = 0;
|
|
u8 reg1 = 0, reg2 = 0, mask = 0;
|
|
|
|
dev_dbg(chip->dev, "%s: USB current_ma = %d\n", __func__, current_ma);
|
|
|
|
if (chip->chg_autonomous_mode) {
|
|
dev_dbg(chip->dev, "%s: Charger in autonmous mode\n", __func__);
|
|
return 0;
|
|
}
|
|
|
|
if (current_ma < USB3_MIN_CURRENT_MA && current_ma != 2)
|
|
current_ma = USB2_MIN_CURRENT_MA;
|
|
|
|
if (current_ma == USB2_MIN_CURRENT_MA) {
|
|
/* USB 2.0 - 100mA */
|
|
reg1 &= ~USB3_ENABLE_BIT;
|
|
reg2 &= ~CMD_B_CHG_USB_500_900_ENABLE_BIT;
|
|
} else if (current_ma == USB2_MAX_CURRENT_MA) {
|
|
/* USB 2.0 - 500mA */
|
|
reg1 &= ~USB3_ENABLE_BIT;
|
|
reg2 |= CMD_B_CHG_USB_500_900_ENABLE_BIT;
|
|
} else if (current_ma == USB3_MAX_CURRENT_MA) {
|
|
/* USB 3.0 - 900mA */
|
|
reg1 |= USB3_ENABLE_BIT;
|
|
reg2 |= CMD_B_CHG_USB_500_900_ENABLE_BIT;
|
|
} else if (current_ma > USB2_MAX_CURRENT_MA) {
|
|
/* HC mode - if none of the above */
|
|
reg2 |= CMD_B_CHG_HC_ENABLE_BIT;
|
|
|
|
for (i = ARRAY_SIZE(chg_current) - 1; i >= 0; i--) {
|
|
if (chg_current[i] <= current_ma)
|
|
break;
|
|
}
|
|
if (i < 0) {
|
|
dev_err(chip->dev, "Cannot find %dmA\n", current_ma);
|
|
i = 0;
|
|
}
|
|
|
|
i = i << AC_CHG_CURRENT_SHIFT;
|
|
rc = smb358_masked_write(chip, CHG_OTH_CURRENT_CTRL_REG,
|
|
AC_CHG_CURRENT_MASK, i);
|
|
if (rc)
|
|
dev_err(chip->dev, "Couldn't set input mA rc=%d\n", rc);
|
|
}
|
|
|
|
mask = CMD_B_CHG_HC_ENABLE_BIT | CMD_B_CHG_USB_500_900_ENABLE_BIT;
|
|
rc = smb358_masked_write(chip, CMD_B_REG, mask, reg2);
|
|
if (rc < 0)
|
|
dev_err(chip->dev, "Couldn't set charging mode rc = %d\n", rc);
|
|
|
|
mask = USB3_ENABLE_MASK;
|
|
rc = smb358_masked_write(chip, SYSOK_AND_USB3_REG, mask, reg1);
|
|
if (rc < 0)
|
|
dev_err(chip->dev, "Couldn't set USB3 mode rc = %d\n", rc);
|
|
|
|
/* Only set suspend bit when chg present and current_ma = 2 */
|
|
if (current_ma == 2 && chip->chg_present) {
|
|
rc = smb358_path_suspend(chip, CURRENT, true);
|
|
if (rc < 0)
|
|
dev_err(chip->dev, "Couldn't suspend rc = %d\n", rc);
|
|
} else {
|
|
rc = smb358_path_suspend(chip, CURRENT, false);
|
|
if (rc < 0)
|
|
dev_err(chip->dev, "Couldn't set susp rc = %d\n", rc);
|
|
}
|
|
|
|
return rc;
|
|
}
|
|
|
|
static int
|
|
smb358_batt_property_is_writeable(struct power_supply *psy,
|
|
enum power_supply_property psp)
|
|
{
|
|
switch (psp) {
|
|
case POWER_SUPPLY_PROP_CHARGING_ENABLED:
|
|
case POWER_SUPPLY_PROP_CAPACITY:
|
|
return 1;
|
|
default:
|
|
break;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int bound_soc(int soc)
|
|
{
|
|
soc = max(0, soc);
|
|
soc = min(soc, 100);
|
|
return soc;
|
|
}
|
|
|
|
static int smb358_battery_set_property(struct power_supply *psy,
|
|
enum power_supply_property prop,
|
|
const union power_supply_propval *val)
|
|
{
|
|
int rc;
|
|
struct smb358_charger *chip = power_supply_get_drvdata(psy);
|
|
|
|
switch (prop) {
|
|
case POWER_SUPPLY_PROP_STATUS:
|
|
if (!chip->bms_controlled_charging)
|
|
return -EINVAL;
|
|
switch (val->intval) {
|
|
case POWER_SUPPLY_STATUS_FULL:
|
|
rc = smb358_charging_disable(chip, SOC, true);
|
|
if (rc < 0) {
|
|
dev_err(chip->dev,
|
|
"Couldn't set charging disable rc = %d\n",
|
|
rc);
|
|
} else {
|
|
chip->batt_full = true;
|
|
dev_dbg(chip->dev, "status = FULL, batt_full = %d\n",
|
|
chip->batt_full);
|
|
}
|
|
break;
|
|
case POWER_SUPPLY_STATUS_DISCHARGING:
|
|
chip->batt_full = false;
|
|
power_supply_changed(chip->batt_psy);
|
|
dev_dbg(chip->dev, "status = DISCHARGING, batt_full = %d\n",
|
|
chip->batt_full);
|
|
break;
|
|
case POWER_SUPPLY_STATUS_CHARGING:
|
|
rc = smb358_charging_disable(chip, SOC, false);
|
|
if (rc < 0) {
|
|
dev_err(chip->dev,
|
|
"Couldn't set charging disable rc = %d\n",
|
|
rc);
|
|
} else {
|
|
chip->batt_full = false;
|
|
dev_dbg(chip->dev, "status = CHARGING, batt_full = %d\n",
|
|
chip->batt_full);
|
|
}
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
break;
|
|
case POWER_SUPPLY_PROP_CHARGING_ENABLED:
|
|
smb358_charging_disable(chip, USER, !val->intval);
|
|
smb358_path_suspend(chip, USER, !val->intval);
|
|
break;
|
|
case POWER_SUPPLY_PROP_CAPACITY:
|
|
chip->fake_battery_soc = bound_soc(val->intval);
|
|
power_supply_changed(chip->batt_psy);
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int smb358_battery_get_property(struct power_supply *psy,
|
|
enum power_supply_property prop,
|
|
union power_supply_propval *val)
|
|
{
|
|
struct smb358_charger *chip = power_supply_get_drvdata(psy);
|
|
|
|
switch (prop) {
|
|
case POWER_SUPPLY_PROP_STATUS:
|
|
val->intval = smb358_get_prop_batt_status(chip);
|
|
break;
|
|
case POWER_SUPPLY_PROP_PRESENT:
|
|
val->intval = smb358_get_prop_batt_present(chip);
|
|
break;
|
|
case POWER_SUPPLY_PROP_CAPACITY:
|
|
val->intval = smb358_get_prop_batt_capacity(chip);
|
|
break;
|
|
case POWER_SUPPLY_PROP_CHARGING_ENABLED:
|
|
val->intval = !(chip->charging_disabled_status & USER);
|
|
break;
|
|
case POWER_SUPPLY_PROP_CHARGE_TYPE:
|
|
val->intval = smb358_get_prop_charge_type(chip);
|
|
break;
|
|
case POWER_SUPPLY_PROP_HEALTH:
|
|
val->intval = smb358_get_prop_batt_health(chip);
|
|
break;
|
|
case POWER_SUPPLY_PROP_TECHNOLOGY:
|
|
val->intval = POWER_SUPPLY_TECHNOLOGY_LION;
|
|
break;
|
|
case POWER_SUPPLY_PROP_MODEL_NAME:
|
|
val->strval = "SMB358";
|
|
break;
|
|
case POWER_SUPPLY_PROP_TEMP:
|
|
val->intval = smb358_get_prop_batt_temp(chip);
|
|
break;
|
|
case POWER_SUPPLY_PROP_VOLTAGE_NOW:
|
|
val->intval = smb358_get_prop_battery_voltage_now(chip);
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static void smb358_set_cable_id(struct smb358_charger *chip,
|
|
u32 id, bool state)
|
|
{
|
|
|
|
dev_dbg(chip->dev, "extcon notify cable %d state %d\n", id, state);
|
|
|
|
extcon_set_state_sync(chip->extcon, chip->cable_id, false);
|
|
if (chip->cable_id == EXTCON_CHG_USB_SDP)
|
|
extcon_set_state_sync(chip->extcon, EXTCON_USB, false);
|
|
|
|
extcon_set_state_sync(chip->extcon, id, state);
|
|
if (id == EXTCON_CHG_USB_SDP)
|
|
extcon_set_state_sync(chip->extcon, EXTCON_USB, state);
|
|
|
|
chip->cable_id = id;
|
|
}
|
|
|
|
static int apsd_complete(struct smb358_charger *chip, u8 status)
|
|
{
|
|
int rc = 0;
|
|
u8 reg = 0;
|
|
enum power_supply_type type = POWER_SUPPLY_TYPE_UNKNOWN;
|
|
u32 id = EXTCON_NONE;
|
|
|
|
/*
|
|
* If apsd is disabled, charger detection is done by
|
|
* DCIN UV irq.
|
|
* status = ZERO - indicates charger removed, handled
|
|
* by DCIN UV irq
|
|
*/
|
|
if (chip->disable_apsd || status == 0) {
|
|
dev_dbg(chip->dev, "APSD %s, status = %d\n",
|
|
chip->disable_apsd ? "disabled" : "enabled", !!status);
|
|
return 0;
|
|
}
|
|
|
|
rc = smb358_read_reg(chip, STATUS_D_REG, ®);
|
|
if (rc) {
|
|
dev_err(chip->dev, "Couldn't read STATUS D rc = %d\n", rc);
|
|
return rc;
|
|
}
|
|
|
|
dev_dbg(chip->dev, "%s: STATUS_D_REG(0x3E)=%x\n", __func__, reg);
|
|
|
|
switch (reg & STATUS_D_CHARGING_PORT_MASK) {
|
|
case STATUS_D_PORT_ACA_DOCK:
|
|
case STATUS_D_PORT_ACA_C:
|
|
case STATUS_D_PORT_ACA_B:
|
|
case STATUS_D_PORT_ACA_A:
|
|
type = POWER_SUPPLY_TYPE_USB_ACA;
|
|
id = EXTCON_CHG_USB_ACA;
|
|
break;
|
|
case STATUS_D_PORT_CDP:
|
|
type = POWER_SUPPLY_TYPE_USB_CDP;
|
|
id = EXTCON_CHG_USB_CDP;
|
|
break;
|
|
case STATUS_D_PORT_DCP:
|
|
type = POWER_SUPPLY_TYPE_USB_DCP;
|
|
id = EXTCON_CHG_USB_DCP;
|
|
break;
|
|
case STATUS_D_PORT_SDP:
|
|
type = POWER_SUPPLY_TYPE_USB;
|
|
id = EXTCON_CHG_USB_SDP;
|
|
break;
|
|
case STATUS_D_PORT_OTHER:
|
|
type = POWER_SUPPLY_TYPE_USB_DCP;
|
|
id = EXTCON_CHG_USB_DCP;
|
|
break;
|
|
default:
|
|
type = POWER_SUPPLY_TYPE_USB;
|
|
id = EXTCON_USB;
|
|
break;
|
|
}
|
|
|
|
chip->chg_present = true;
|
|
chip->charger_type = type;
|
|
dev_dbg(chip->dev,
|
|
"APSD complete. USB type detected=%d chg_present=%d",
|
|
type, chip->chg_present);
|
|
|
|
/* set the charge current as required */
|
|
if (type == POWER_SUPPLY_TYPE_USB)
|
|
chip->usb_psy_ma = USB2_MAX_CURRENT_MA;
|
|
else /* DCP or CDP */
|
|
chip->usb_psy_ma = DCP_MAX_CURRENT_MA;
|
|
|
|
smb358_enable_volatile_writes(chip);
|
|
rc = smb358_set_usb_chg_current(chip, chip->usb_psy_ma);
|
|
if (rc < 0)
|
|
dev_dbg(chip->dev, "Failed to set USB current rc=%d\n", rc);
|
|
|
|
smb358_set_cable_id(chip, id, true);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int chg_uv(struct smb358_charger *chip, u8 status)
|
|
{
|
|
int rc;
|
|
|
|
/* use this to detect USB insertion only if !apsd */
|
|
if (chip->disable_apsd && status == 0) {
|
|
chip->chg_present = true;
|
|
chip->charger_type = POWER_SUPPLY_TYPE_USB;
|
|
smb358_set_cable_id(chip, EXTCON_USB, true);
|
|
|
|
if (chip->bms_controlled_charging) {
|
|
/*
|
|
* Disable SOC based USB suspend to enable
|
|
* charging on USB insertion.
|
|
*/
|
|
rc = smb358_charging_disable(chip, SOC, false);
|
|
if (rc < 0)
|
|
dev_err(chip->dev,
|
|
"Couldn't disable usb suspend rc = %d\n",
|
|
rc);
|
|
}
|
|
}
|
|
|
|
if (status != 0) {
|
|
chip->chg_present = false;
|
|
/*
|
|
* we can't set usb_psy as UNKNOWN here, will lead
|
|
* USERSPACE issue
|
|
*/
|
|
smb358_set_cable_id(chip, EXTCON_USB, false);
|
|
}
|
|
|
|
dev_dbg(chip->dev, "chip->chg_present = %d\n", chip->chg_present);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int chg_ov(struct smb358_charger *chip, u8 status)
|
|
{
|
|
if (status)
|
|
chip->usb_psy_health = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
|
|
else
|
|
chip->usb_psy_health = POWER_SUPPLY_HEALTH_GOOD;
|
|
|
|
power_supply_changed(chip->usb_psy);
|
|
return 0;
|
|
}
|
|
|
|
#define STATUS_FAST_CHARGING BIT(6)
|
|
static int fast_chg(struct smb358_charger *chip, u8 status)
|
|
{
|
|
dev_dbg(chip->dev, "%s\n", __func__);
|
|
|
|
if (status & STATUS_FAST_CHARGING)
|
|
chip->batt_full = false;
|
|
return 0;
|
|
}
|
|
|
|
static int chg_term(struct smb358_charger *chip, u8 status)
|
|
{
|
|
dev_dbg(chip->dev, "%s\n", __func__);
|
|
if (!chip->iterm_disabled)
|
|
chip->batt_full = !!status;
|
|
return 0;
|
|
}
|
|
|
|
static int taper_chg(struct smb358_charger *chip, u8 status)
|
|
{
|
|
dev_dbg(chip->dev, "%s\n", __func__);
|
|
return 0;
|
|
}
|
|
|
|
static int chg_recharge(struct smb358_charger *chip, u8 status)
|
|
{
|
|
dev_dbg(chip->dev, "%s, status = %d\n", __func__, !!status);
|
|
/* to check the status mean */
|
|
chip->batt_full = !status;
|
|
return 0;
|
|
}
|
|
|
|
/* only for SMB thermal */
|
|
static int hot_hard_handler(struct smb358_charger *chip, u8 status)
|
|
{
|
|
pr_debug("status = 0x%02x\n", status);
|
|
chip->batt_hot = !!status;
|
|
return 0;
|
|
}
|
|
static int cold_hard_handler(struct smb358_charger *chip, u8 status)
|
|
{
|
|
pr_debug("status = 0x%02x\n", status);
|
|
chip->batt_cold = !!status;
|
|
return 0;
|
|
}
|
|
static int hot_soft_handler(struct smb358_charger *chip, u8 status)
|
|
{
|
|
pr_debug("status = 0x%02x\n", status);
|
|
chip->batt_warm = !!status;
|
|
return 0;
|
|
}
|
|
static int cold_soft_handler(struct smb358_charger *chip, u8 status)
|
|
{
|
|
pr_debug("status = 0x%02x\n", status);
|
|
chip->batt_cool = !!status;
|
|
return 0;
|
|
}
|
|
|
|
static int battery_missing(struct smb358_charger *chip, u8 status)
|
|
{
|
|
chip->battery_missing = !!status;
|
|
return 0;
|
|
}
|
|
|
|
static int otg_handler(struct smb358_charger *chip, u8 status)
|
|
{
|
|
smb358_set_cable_id(chip, EXTCON_USB_HOST, !!status);
|
|
return 0;
|
|
}
|
|
|
|
static struct irq_handler_info handlers[] = {
|
|
[0] = {
|
|
.stat_reg = IRQ_A_REG,
|
|
.val = 0,
|
|
.prev_val = 0,
|
|
.irq_info = {
|
|
{
|
|
.name = "cold_soft",
|
|
.smb_irq = cold_soft_handler,
|
|
},
|
|
{
|
|
.name = "hot_soft",
|
|
.smb_irq = hot_soft_handler,
|
|
},
|
|
{
|
|
.name = "cold_hard",
|
|
.smb_irq = cold_hard_handler,
|
|
},
|
|
{
|
|
.name = "hot_hard",
|
|
.smb_irq = hot_hard_handler,
|
|
},
|
|
},
|
|
},
|
|
[1] = {
|
|
.stat_reg = IRQ_B_REG,
|
|
.val = 0,
|
|
.prev_val = 0,
|
|
.irq_info = {
|
|
{
|
|
.name = "chg_hot",
|
|
},
|
|
{
|
|
.name = "vbat_low",
|
|
},
|
|
{
|
|
.name = "battery_missing",
|
|
.smb_irq = battery_missing
|
|
},
|
|
{
|
|
.name = "battery_ov",
|
|
},
|
|
},
|
|
},
|
|
[2] = {
|
|
.stat_reg = IRQ_C_REG,
|
|
.val = 0,
|
|
.prev_val = 0,
|
|
.irq_info = {
|
|
{
|
|
.name = "chg_term",
|
|
.smb_irq = chg_term,
|
|
},
|
|
{
|
|
.name = "taper",
|
|
.smb_irq = taper_chg,
|
|
},
|
|
{
|
|
.name = "recharge",
|
|
.smb_irq = chg_recharge,
|
|
},
|
|
{
|
|
.name = "fast_chg",
|
|
.smb_irq = fast_chg,
|
|
},
|
|
},
|
|
},
|
|
[3] = {
|
|
.stat_reg = IRQ_D_REG,
|
|
.val = 0,
|
|
.prev_val = 0,
|
|
.irq_info = {
|
|
{
|
|
.name = "prechg_timeout",
|
|
},
|
|
{
|
|
.name = "safety_timeout",
|
|
},
|
|
{
|
|
.name = "aicl_complete",
|
|
},
|
|
{
|
|
.name = "src_detect",
|
|
.smb_irq = apsd_complete,
|
|
},
|
|
},
|
|
},
|
|
[4] = {
|
|
.stat_reg = IRQ_E_REG,
|
|
.val = 0,
|
|
.prev_val = 0,
|
|
.irq_info = {
|
|
{
|
|
.name = "usbin_uv",
|
|
.smb_irq = chg_uv,
|
|
},
|
|
{
|
|
.name = "usbin_ov",
|
|
.smb_irq = chg_ov,
|
|
},
|
|
{
|
|
.name = "unknown",
|
|
},
|
|
{
|
|
.name = "unknown",
|
|
},
|
|
},
|
|
},
|
|
[5] = {
|
|
.stat_reg = IRQ_F_REG,
|
|
.val = 0,
|
|
.prev_val = 0,
|
|
.irq_info = {
|
|
{
|
|
.name = "power_ok",
|
|
},
|
|
{
|
|
.name = "otg_det",
|
|
.smb_irq = otg_handler,
|
|
},
|
|
{
|
|
.name = "otg_batt_uv",
|
|
},
|
|
{
|
|
.name = "otg_oc",
|
|
},
|
|
},
|
|
},
|
|
};
|
|
|
|
#define IRQ_LATCHED_MASK 0x02
|
|
#define IRQ_STATUS_MASK 0x01
|
|
#define BITS_PER_IRQ 2
|
|
static irqreturn_t smb358_chg_stat_handler(int irq, void *dev_id)
|
|
{
|
|
struct smb358_charger *chip = dev_id;
|
|
int i, j;
|
|
u8 triggered;
|
|
u8 changed;
|
|
u8 rt_stat, prev_rt_stat;
|
|
int rc;
|
|
int handler_count = 0;
|
|
|
|
mutex_lock(&chip->irq_complete);
|
|
|
|
chip->irq_waiting = true;
|
|
if (!chip->resume_completed) {
|
|
dev_dbg(chip->dev, "IRQ triggered before device-resume\n");
|
|
disable_irq_nosync(irq);
|
|
mutex_unlock(&chip->irq_complete);
|
|
return IRQ_HANDLED;
|
|
}
|
|
chip->irq_waiting = false;
|
|
|
|
for (i = 0; i < ARRAY_SIZE(handlers); i++) {
|
|
rc = smb358_read_reg(chip, handlers[i].stat_reg,
|
|
&handlers[i].val);
|
|
if (rc < 0) {
|
|
dev_err(chip->dev, "Couldn't read %d rc = %d\n",
|
|
handlers[i].stat_reg, rc);
|
|
continue;
|
|
}
|
|
|
|
for (j = 0; j < ARRAY_SIZE(handlers[i].irq_info); j++) {
|
|
triggered = handlers[i].val
|
|
& (IRQ_LATCHED_MASK << (j * BITS_PER_IRQ));
|
|
rt_stat = handlers[i].val
|
|
& (IRQ_STATUS_MASK << (j * BITS_PER_IRQ));
|
|
prev_rt_stat = handlers[i].prev_val
|
|
& (IRQ_STATUS_MASK << (j * BITS_PER_IRQ));
|
|
changed = prev_rt_stat ^ rt_stat;
|
|
|
|
if (triggered || changed)
|
|
rt_stat ? handlers[i].irq_info[j].high++ :
|
|
handlers[i].irq_info[j].low++;
|
|
|
|
if ((triggered || changed)
|
|
&& handlers[i].irq_info[j].smb_irq != NULL) {
|
|
handler_count++;
|
|
rc = handlers[i].irq_info[j].smb_irq(chip,
|
|
rt_stat);
|
|
if (rc < 0)
|
|
dev_err(chip->dev,
|
|
"Couldn't handle %d irq for reg 0x%02x rc = %d\n",
|
|
j, handlers[i].stat_reg, rc);
|
|
}
|
|
}
|
|
handlers[i].prev_val = handlers[i].val;
|
|
}
|
|
|
|
dev_dbg(chip->dev, "handler count = %d\n", handler_count);
|
|
if (handler_count) {
|
|
dev_dbg(chip->dev, "batt psy changed\n");
|
|
power_supply_changed(chip->batt_psy);
|
|
}
|
|
|
|
mutex_unlock(&chip->irq_complete);
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static irqreturn_t smb358_chg_valid_handler(int irq, void *dev_id)
|
|
{
|
|
struct smb358_charger *chip = dev_id;
|
|
int present;
|
|
|
|
present = gpio_get_value_cansleep(chip->chg_valid_gpio);
|
|
if (present < 0) {
|
|
dev_err(chip->dev, "Couldn't read chg_valid gpio=%d\n",
|
|
chip->chg_valid_gpio);
|
|
return IRQ_HANDLED;
|
|
}
|
|
present ^= chip->chg_valid_act_low;
|
|
|
|
dev_dbg(chip->dev, "%s: chg_present = %d\n", __func__, present);
|
|
|
|
if (present != chip->chg_present) {
|
|
chip->chg_present = present;
|
|
dev_dbg(chip->dev, "%s updating usb_psy present=%d",
|
|
__func__, chip->chg_present);
|
|
power_supply_changed(chip->usb_psy);
|
|
}
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static void smb358_external_power_changed(struct power_supply *psy)
|
|
{
|
|
struct smb358_charger *chip = power_supply_get_drvdata(psy);
|
|
union power_supply_propval prop = {0,};
|
|
int rc, current_limit = 0;
|
|
|
|
if (chip->bms_psy_name)
|
|
chip->bms_psy =
|
|
power_supply_get_by_name((char *)chip->bms_psy_name);
|
|
|
|
rc = power_supply_get_property(chip->usb_psy,
|
|
POWER_SUPPLY_PROP_CURRENT_MAX, &prop);
|
|
if (rc)
|
|
dev_err(chip->dev,
|
|
"Couldn't read USB current_max property, rc=%d\n",
|
|
rc);
|
|
else
|
|
current_limit = prop.intval / 1000;
|
|
|
|
smb358_enable_volatile_writes(chip);
|
|
smb358_set_usb_chg_current(chip, current_limit);
|
|
|
|
dev_dbg(chip->dev, "current_limit = %d\n", current_limit);
|
|
}
|
|
|
|
#if defined(CONFIG_DEBUG_FS)
|
|
#define LAST_CNFG_REG 0x13
|
|
static int show_cnfg_regs(struct seq_file *m, void *data)
|
|
{
|
|
struct smb358_charger *chip = m->private;
|
|
int rc;
|
|
u8 reg;
|
|
u8 addr;
|
|
|
|
for (addr = 0; addr <= LAST_CNFG_REG; addr++) {
|
|
rc = smb358_read_reg(chip, addr, ®);
|
|
if (!rc)
|
|
seq_printf(m, "0x%02x = 0x%02x\n", addr, reg);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int cnfg_debugfs_open(struct inode *inode, struct file *file)
|
|
{
|
|
struct smb358_charger *chip = inode->i_private;
|
|
|
|
return single_open(file, show_cnfg_regs, chip);
|
|
}
|
|
|
|
static const struct file_operations cnfg_debugfs_ops = {
|
|
.owner = THIS_MODULE,
|
|
.open = cnfg_debugfs_open,
|
|
.read = seq_read,
|
|
.llseek = seq_lseek,
|
|
.release = single_release,
|
|
};
|
|
|
|
#define FIRST_CMD_REG 0x30
|
|
#define LAST_CMD_REG 0x33
|
|
static int show_cmd_regs(struct seq_file *m, void *data)
|
|
{
|
|
struct smb358_charger *chip = m->private;
|
|
int rc;
|
|
u8 reg;
|
|
u8 addr;
|
|
|
|
for (addr = FIRST_CMD_REG; addr <= LAST_CMD_REG; addr++) {
|
|
rc = smb358_read_reg(chip, addr, ®);
|
|
if (!rc)
|
|
seq_printf(m, "0x%02x = 0x%02x\n", addr, reg);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int cmd_debugfs_open(struct inode *inode, struct file *file)
|
|
{
|
|
struct smb358_charger *chip = inode->i_private;
|
|
|
|
return single_open(file, show_cmd_regs, chip);
|
|
}
|
|
|
|
static const struct file_operations cmd_debugfs_ops = {
|
|
.owner = THIS_MODULE,
|
|
.open = cmd_debugfs_open,
|
|
.read = seq_read,
|
|
.llseek = seq_lseek,
|
|
.release = single_release,
|
|
};
|
|
|
|
#define FIRST_STATUS_REG 0x35
|
|
#define LAST_STATUS_REG 0x3F
|
|
static int show_status_regs(struct seq_file *m, void *data)
|
|
{
|
|
struct smb358_charger *chip = m->private;
|
|
int rc;
|
|
u8 reg;
|
|
u8 addr;
|
|
|
|
for (addr = FIRST_STATUS_REG; addr <= LAST_STATUS_REG; addr++) {
|
|
rc = smb358_read_reg(chip, addr, ®);
|
|
if (!rc)
|
|
seq_printf(m, "0x%02x = 0x%02x\n", addr, reg);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int status_debugfs_open(struct inode *inode, struct file *file)
|
|
{
|
|
struct smb358_charger *chip = inode->i_private;
|
|
|
|
return single_open(file, show_status_regs, chip);
|
|
}
|
|
|
|
static const struct file_operations status_debugfs_ops = {
|
|
.owner = THIS_MODULE,
|
|
.open = status_debugfs_open,
|
|
.read = seq_read,
|
|
.llseek = seq_lseek,
|
|
.release = single_release,
|
|
};
|
|
|
|
static int show_irq_count(struct seq_file *m, void *data)
|
|
{
|
|
int i, j, total = 0;
|
|
|
|
for (i = 0; i < ARRAY_SIZE(handlers); i++)
|
|
for (j = 0; j < 4; j++) {
|
|
seq_printf(m, "%s=%d\t(high=%d low=%d)\n",
|
|
handlers[i].irq_info[j].name,
|
|
handlers[i].irq_info[j].high
|
|
+ handlers[i].irq_info[j].low,
|
|
handlers[i].irq_info[j].high,
|
|
handlers[i].irq_info[j].low);
|
|
total += (handlers[i].irq_info[j].high
|
|
+ handlers[i].irq_info[j].low);
|
|
}
|
|
|
|
seq_printf(m, "\n\tTotal = %d\n", total);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int irq_count_debugfs_open(struct inode *inode, struct file *file)
|
|
{
|
|
struct smb358_charger *chip = inode->i_private;
|
|
|
|
return single_open(file, show_irq_count, chip);
|
|
}
|
|
|
|
static const struct file_operations irq_count_debugfs_ops = {
|
|
.owner = THIS_MODULE,
|
|
.open = irq_count_debugfs_open,
|
|
.read = seq_read,
|
|
.llseek = seq_lseek,
|
|
.release = single_release,
|
|
};
|
|
|
|
static int get_reg(void *data, u64 *val)
|
|
{
|
|
struct smb358_charger *chip = data;
|
|
int rc;
|
|
u8 temp;
|
|
|
|
rc = smb358_read_reg(chip, chip->peek_poke_address, &temp);
|
|
if (rc < 0) {
|
|
dev_err(chip->dev,
|
|
"Couldn't read reg %x rc = %d\n",
|
|
chip->peek_poke_address, rc);
|
|
return -EAGAIN;
|
|
}
|
|
*val = temp;
|
|
return 0;
|
|
}
|
|
|
|
static int set_reg(void *data, u64 val)
|
|
{
|
|
struct smb358_charger *chip = data;
|
|
int rc;
|
|
u8 temp;
|
|
|
|
temp = (u8) val;
|
|
rc = smb358_write_reg(chip, chip->peek_poke_address, temp);
|
|
if (rc < 0) {
|
|
dev_err(chip->dev,
|
|
"Couldn't write 0x%02x to 0x%02x rc= %d\n",
|
|
chip->peek_poke_address, temp, rc);
|
|
return -EAGAIN;
|
|
}
|
|
return 0;
|
|
}
|
|
DEFINE_SIMPLE_ATTRIBUTE(poke_poke_debug_ops, get_reg, set_reg, "0x%02llx\n");
|
|
|
|
static int force_irq_set(void *data, u64 val)
|
|
{
|
|
struct smb358_charger *chip = data;
|
|
|
|
smb358_chg_stat_handler(chip->client->irq, data);
|
|
return 0;
|
|
}
|
|
DEFINE_SIMPLE_ATTRIBUTE(force_irq_ops, NULL, force_irq_set, "0x%02llx\n");
|
|
#endif
|
|
|
|
#ifdef DEBUG
|
|
static void dump_regs(struct smb358_charger *chip)
|
|
{
|
|
int rc;
|
|
u8 reg;
|
|
u8 addr;
|
|
|
|
for (addr = 0; addr <= LAST_CNFG_REG; addr++) {
|
|
rc = smb358_read_reg(chip, addr, ®);
|
|
if (rc)
|
|
dev_err(chip->dev, "Couldn't read 0x%02x rc = %d\n",
|
|
addr, rc);
|
|
else
|
|
pr_debug("0x%02x = 0x%02x\n", addr, reg);
|
|
}
|
|
|
|
for (addr = FIRST_STATUS_REG; addr <= LAST_STATUS_REG; addr++) {
|
|
rc = smb358_read_reg(chip, addr, ®);
|
|
if (rc)
|
|
dev_err(chip->dev, "Couldn't read 0x%02x rc = %d\n",
|
|
addr, rc);
|
|
else
|
|
pr_debug("0x%02x = 0x%02x\n", addr, reg);
|
|
}
|
|
|
|
for (addr = FIRST_CMD_REG; addr <= LAST_CMD_REG; addr++) {
|
|
rc = smb358_read_reg(chip, addr, ®);
|
|
if (rc)
|
|
dev_err(chip->dev, "Couldn't read 0x%02x rc = %d\n",
|
|
addr, rc);
|
|
else
|
|
pr_debug("0x%02x = 0x%02x\n", addr, reg);
|
|
}
|
|
}
|
|
#else
|
|
static void dump_regs(struct smb358_charger *chip)
|
|
{
|
|
}
|
|
#endif
|
|
|
|
static int smb_parse_batt_id(struct smb358_charger *chip)
|
|
{
|
|
int rc = 0, rpull = 0, vref = 0;
|
|
int64_t denom, batt_id_uv, numerator;
|
|
struct device_node *node = chip->dev->of_node;
|
|
int batt_id_result = 0;
|
|
|
|
rc = of_property_read_u32(node, "qcom,batt-id-vref-uv", &vref);
|
|
if (rc < 0) {
|
|
dev_err(chip->dev,
|
|
"Couldn't read batt-id-vref-uv rc=%d\n", rc);
|
|
return rc;
|
|
}
|
|
|
|
rc = of_property_read_u32(node, "qcom,batt-id-rpullup-kohm", &rpull);
|
|
if (rc < 0) {
|
|
dev_err(chip->dev,
|
|
"Couldn't read batt-id-rpullup-kohm rc=%d\n", rc);
|
|
return rc;
|
|
}
|
|
|
|
if (chip->iio.batt_id_therm) {
|
|
rc = iio_read_channel_processed(chip->iio.batt_id_therm,
|
|
&batt_id_result);
|
|
if (rc < 0) {
|
|
pr_err("Couldn't read batt id channel=%d, rc = %d\n",
|
|
VADC_LR_MUX2_BAT_ID, rc);
|
|
return -EINVAL;
|
|
}
|
|
}
|
|
|
|
/* batt_id_result is in mv */
|
|
batt_id_uv = batt_id_result * 1000;
|
|
|
|
if (batt_id_uv == 0) {
|
|
/* vadc not correct or batt id line grounded, report 0 kohms */
|
|
dev_warn(chip->dev, "batt_id_uv=0, batt-id grounded\n");
|
|
return 0;
|
|
}
|
|
|
|
numerator = batt_id_uv * rpull * 1000;
|
|
denom = vref - batt_id_uv;
|
|
|
|
/* batt id connector might be open, return 0 kohms */
|
|
if (denom == 0)
|
|
return 0;
|
|
|
|
chip->connected_rid = div64_s64(numerator, denom);
|
|
|
|
dev_dbg(chip->dev,
|
|
"batt_id_voltage=%lld numerator=%lld denom=%lld connected_rid=%d\n",
|
|
batt_id_uv, numerator, denom, chip->connected_rid);
|
|
return 0;
|
|
}
|
|
|
|
static int smb_parse_dt(struct smb358_charger *chip)
|
|
{
|
|
int rc;
|
|
enum of_gpio_flags gpio_flags;
|
|
struct device_node *node = chip->dev->of_node;
|
|
|
|
if (!node) {
|
|
dev_err(chip->dev, "device tree info. missing\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
chip->charging_disabled = of_property_read_bool(node,
|
|
"qcom,charger-disabled");
|
|
|
|
chip->inhibit_disabled = of_property_read_bool(node,
|
|
"qcom,chg-inhibit-disabled");
|
|
chip->chg_autonomous_mode = of_property_read_bool(node,
|
|
"qcom,chg-autonomous-mode");
|
|
|
|
chip->disable_apsd = of_property_read_bool(node, "qcom,disable-apsd");
|
|
|
|
chip->bms_controlled_charging = of_property_read_bool(node,
|
|
"qcom,bms-controlled-charging");
|
|
|
|
rc = of_property_read_string(node, "qcom,bms-psy-name",
|
|
&chip->bms_psy_name);
|
|
if (rc)
|
|
chip->bms_psy_name = NULL;
|
|
|
|
chip->chg_valid_gpio = of_get_named_gpio_flags(node,
|
|
"qcom,chg-valid-gpio", 0, &gpio_flags);
|
|
if (!gpio_is_valid(chip->chg_valid_gpio))
|
|
dev_dbg(chip->dev, "Invalid chg-valid-gpio");
|
|
else
|
|
chip->chg_valid_act_low = gpio_flags & OF_GPIO_ACTIVE_LOW;
|
|
|
|
rc = of_property_read_u32(node, "qcom,fastchg-current-max-ma",
|
|
&chip->fastchg_current_max_ma);
|
|
if (rc)
|
|
chip->fastchg_current_max_ma = SMB358_FAST_CHG_MAX_MA;
|
|
|
|
chip->iterm_disabled = of_property_read_bool(node,
|
|
"qcom,iterm-disabled");
|
|
|
|
rc = of_property_read_u32(node, "qcom,iterm-ma", &chip->iterm_ma);
|
|
if (rc < 0)
|
|
chip->iterm_ma = -EINVAL;
|
|
|
|
rc = of_property_read_u32(node, "qcom,float-voltage-mv",
|
|
&chip->vfloat_mv);
|
|
if (rc < 0) {
|
|
chip->vfloat_mv = -EINVAL;
|
|
pr_err("float-voltage-mv property missing, exit\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
rc = of_property_read_u32(node, "qcom,recharge-mv",
|
|
&chip->recharge_mv);
|
|
if (rc < 0)
|
|
chip->recharge_mv = -EINVAL;
|
|
|
|
chip->recharge_disabled = of_property_read_bool(node,
|
|
"qcom,recharge-disabled");
|
|
chip->pinctrl_state_name = of_get_property(node, "pinctrl-names", NULL);
|
|
|
|
/* Extract ADC channels */
|
|
rc = smb358_get_iio_channel(chip, "vbat_sns", &chip->iio.vbat_sns);
|
|
if (rc < 0)
|
|
return rc;
|
|
|
|
rc = smb358_get_iio_channel(chip,
|
|
"batt_id_therm", &chip->iio.batt_id_therm);
|
|
if (rc < 0)
|
|
return rc;
|
|
|
|
if (of_get_property(node, "qcom,vcc-i2c-supply", NULL)) {
|
|
chip->vcc_i2c = devm_regulator_get(chip->dev, "vcc-i2c");
|
|
if (IS_ERR(chip->vcc_i2c)) {
|
|
dev_err(chip->dev,
|
|
"%s: Failed to get vcc_i2c regulator\n",
|
|
__func__);
|
|
return PTR_ERR(chip->vcc_i2c);
|
|
}
|
|
}
|
|
|
|
chip->skip_usb_suspend_for_fake_battery = of_property_read_bool(node,
|
|
"qcom,skip-usb-suspend-for-fake-battery");
|
|
if (!chip->skip_usb_suspend_for_fake_battery) {
|
|
rc = smb_parse_batt_id(chip);
|
|
if (rc) {
|
|
dev_err(chip->dev,
|
|
"failed to read batt-id rc=%d\n", rc);
|
|
return rc;
|
|
}
|
|
}
|
|
|
|
pr_debug("inhibit-disabled = %d, recharge-disabled = %d, recharge-mv = %d,",
|
|
chip->inhibit_disabled, chip->recharge_disabled,
|
|
chip->recharge_mv);
|
|
pr_debug("vfloat-mv = %d, iterm-disabled = %d,",
|
|
chip->vfloat_mv, chip->iterm_disabled);
|
|
pr_debug("fastchg-current = %d, charging-disabled = %d,",
|
|
chip->fastchg_current_max_ma, chip->charging_disabled);
|
|
pr_debug("disable-apsd = %d bms = %s,",
|
|
chip->disable_apsd, chip->bms_psy_name);
|
|
return 0;
|
|
}
|
|
|
|
static int determine_initial_state(struct smb358_charger *chip)
|
|
{
|
|
int rc;
|
|
u8 reg = 0;
|
|
|
|
rc = smb358_read_reg(chip, IRQ_B_REG, ®);
|
|
if (rc) {
|
|
dev_err(chip->dev, "Couldn't read IRQ_B rc = %d\n", rc);
|
|
goto fail_init_status;
|
|
}
|
|
|
|
rc = smb358_read_reg(chip, IRQ_C_REG, ®);
|
|
if (rc) {
|
|
dev_err(chip->dev, "Couldn't read IRQ_C rc = %d\n", rc);
|
|
goto fail_init_status;
|
|
}
|
|
chip->batt_full = (reg & IRQ_C_TERM_BIT) ? true : false;
|
|
|
|
rc = smb358_read_reg(chip, IRQ_A_REG, ®);
|
|
if (rc < 0) {
|
|
dev_err(chip->dev, "Couldn't read irq A rc = %d\n", rc);
|
|
return rc;
|
|
}
|
|
|
|
/* For current design, can ignore this */
|
|
if (reg & IRQ_A_HOT_HARD_BIT)
|
|
chip->batt_hot = true;
|
|
if (reg & IRQ_A_COLD_HARD_BIT)
|
|
chip->batt_cold = true;
|
|
if (reg & IRQ_A_HOT_SOFT_BIT)
|
|
chip->batt_warm = true;
|
|
if (reg & IRQ_A_COLD_SOFT_BIT)
|
|
chip->batt_cool = true;
|
|
|
|
rc = smb358_read_reg(chip, IRQ_E_REG, ®);
|
|
if (rc) {
|
|
dev_err(chip->dev, "Couldn't read IRQ_E rc = %d\n", rc);
|
|
goto fail_init_status;
|
|
}
|
|
|
|
if (reg & IRQ_E_INPUT_UV_BIT) {
|
|
chg_uv(chip, 1);
|
|
} else {
|
|
chg_uv(chip, 0);
|
|
apsd_complete(chip, 1);
|
|
}
|
|
|
|
return 0;
|
|
|
|
fail_init_status:
|
|
dev_err(chip->dev, "Couldn't determine initial status\n");
|
|
return rc;
|
|
}
|
|
|
|
#if defined(CONFIG_DEBUG_FS)
|
|
static void smb358_debugfs_init(struct smb358_charger *chip)
|
|
{
|
|
int rc;
|
|
|
|
chip->debug_root = debugfs_create_dir("smb358", NULL);
|
|
if (!chip->debug_root)
|
|
dev_err(chip->dev, "Couldn't create debug dir\n");
|
|
|
|
if (chip->debug_root) {
|
|
struct dentry *ent;
|
|
|
|
ent = debugfs_create_file("config_registers", S_IFREG | 0444,
|
|
chip->debug_root, chip,
|
|
&cnfg_debugfs_ops);
|
|
if (!ent || IS_ERR(ent)) {
|
|
rc = PTR_ERR(ent);
|
|
dev_err(chip->dev,
|
|
"Couldn't create cnfg debug file rc = %d\n",
|
|
rc);
|
|
}
|
|
|
|
ent = debugfs_create_file("status_registers", S_IFREG | 0444,
|
|
chip->debug_root, chip,
|
|
&status_debugfs_ops);
|
|
if (!ent || IS_ERR(ent)) {
|
|
rc = PTR_ERR(ent);
|
|
dev_err(chip->dev,
|
|
"Couldn't create status debug file rc = %d\n",
|
|
rc);
|
|
}
|
|
|
|
ent = debugfs_create_file("cmd_registers", S_IFREG | 0444,
|
|
chip->debug_root, chip,
|
|
&cmd_debugfs_ops);
|
|
if (!ent || IS_ERR(ent)) {
|
|
rc = PTR_ERR(ent);
|
|
dev_err(chip->dev,
|
|
"Couldn't create cmd debug file rc = %d\n",
|
|
rc);
|
|
}
|
|
|
|
ent = debugfs_create_x32("address", S_IFREG | 0644,
|
|
chip->debug_root,
|
|
&(chip->peek_poke_address));
|
|
if (!ent || IS_ERR(ent)) {
|
|
rc = PTR_ERR(ent);
|
|
dev_err(chip->dev,
|
|
"Couldn't create address debug file rc = %d\n",
|
|
rc);
|
|
}
|
|
|
|
ent = debugfs_create_file("data", S_IFREG | 0644,
|
|
chip->debug_root, chip,
|
|
&poke_poke_debug_ops);
|
|
if (!ent || IS_ERR(ent)) {
|
|
rc = PTR_ERR(ent);
|
|
dev_err(chip->dev,
|
|
"Couldn't create data debug file rc = %d\n",
|
|
rc);
|
|
}
|
|
|
|
ent = debugfs_create_file("force_irq",
|
|
S_IFREG | 0644,
|
|
chip->debug_root, chip,
|
|
&force_irq_ops);
|
|
if (!ent || IS_ERR(ent)) {
|
|
rc = PTR_ERR(ent);
|
|
dev_err(chip->dev,
|
|
"Couldn't create force_irq debug file rc =%d\n",
|
|
rc);
|
|
}
|
|
|
|
ent = debugfs_create_file("irq_count", S_IFREG | 0444,
|
|
chip->debug_root, chip,
|
|
&irq_count_debugfs_ops);
|
|
if (!ent || IS_ERR(ent)) {
|
|
rc = PTR_ERR(ent);
|
|
dev_err(chip->dev,
|
|
"Couldn't create cnfg irq_count file rc = %d\n",
|
|
rc);
|
|
}
|
|
}
|
|
}
|
|
#else
|
|
static void smb358_debugfs_init(struct smb358_charger *chip)
|
|
{
|
|
}
|
|
#endif
|
|
|
|
static char *smb358_usb_supplicants[] = {
|
|
"bms",
|
|
};
|
|
|
|
static enum power_supply_property smb358_usb_properties[] = {
|
|
POWER_SUPPLY_PROP_PRESENT,
|
|
POWER_SUPPLY_PROP_ONLINE,
|
|
POWER_SUPPLY_PROP_CURRENT_MAX,
|
|
POWER_SUPPLY_PROP_SDP_CURRENT_MAX,
|
|
POWER_SUPPLY_PROP_TYPE,
|
|
POWER_SUPPLY_PROP_REAL_TYPE,
|
|
};
|
|
|
|
static int smb358_usb_get_property(struct power_supply *psy,
|
|
enum power_supply_property psp,
|
|
union power_supply_propval *val)
|
|
{
|
|
struct smb358_charger *chip = power_supply_get_drvdata(psy);
|
|
|
|
switch (psp) {
|
|
case POWER_SUPPLY_PROP_CURRENT_MAX:
|
|
case POWER_SUPPLY_PROP_SDP_CURRENT_MAX:
|
|
val->intval = chip->usb_psy_ma * 1000;
|
|
break;
|
|
case POWER_SUPPLY_PROP_PRESENT:
|
|
val->intval = chip->chg_present;
|
|
break;
|
|
case POWER_SUPPLY_PROP_ONLINE:
|
|
val->intval = chip->chg_present && !chip->usb_suspended;
|
|
break;
|
|
case POWER_SUPPLY_PROP_TYPE:
|
|
val->intval = chip->charger_type;
|
|
break;
|
|
case POWER_SUPPLY_PROP_REAL_TYPE:
|
|
if (chip->charger_type == POWER_SUPPLY_TYPE_UNKNOWN)
|
|
val->intval = POWER_SUPPLY_TYPE_USB;
|
|
else
|
|
val->intval = chip->charger_type;
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static int smb358_usb_set_property(struct power_supply *psy,
|
|
enum power_supply_property psp,
|
|
const union power_supply_propval *val)
|
|
{
|
|
struct smb358_charger *chip = power_supply_get_drvdata(psy);
|
|
|
|
switch (psp) {
|
|
case POWER_SUPPLY_PROP_CURRENT_MAX:
|
|
case POWER_SUPPLY_PROP_SDP_CURRENT_MAX:
|
|
chip->usb_psy_ma = val->intval / 1000;
|
|
smb358_enable_volatile_writes(chip);
|
|
smb358_set_usb_chg_current(chip, chip->usb_psy_ma);
|
|
break;
|
|
default:
|
|
return -EINVAL;
|
|
}
|
|
|
|
power_supply_changed(psy);
|
|
return 0;
|
|
}
|
|
|
|
static int smb358_usb_is_writeable(struct power_supply *psy,
|
|
enum power_supply_property psp)
|
|
{
|
|
switch (psp) {
|
|
case POWER_SUPPLY_PROP_CURRENT_MAX:
|
|
return 1;
|
|
default:
|
|
break;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
#define SMB_I2C_VTG_MIN_UV 1800000
|
|
#define SMB_I2C_VTG_MAX_UV 1800000
|
|
static int smb358_charger_probe(struct i2c_client *client,
|
|
const struct i2c_device_id *id)
|
|
{
|
|
u8 reg = 0;
|
|
int rc, irq;
|
|
struct smb358_charger *chip;
|
|
struct power_supply_config batt_psy_cfg = {};
|
|
struct power_supply_config usb_psy_cfg = {};
|
|
|
|
chip = devm_kzalloc(&client->dev, sizeof(*chip), GFP_KERNEL);
|
|
if (!chip)
|
|
return -ENOMEM;
|
|
|
|
chip->client = client;
|
|
chip->dev = &client->dev;
|
|
chip->fake_battery_soc = -EINVAL;
|
|
|
|
chip->extcon = devm_extcon_dev_allocate(chip->dev,
|
|
smb358_extcon_cable);
|
|
if (IS_ERR(chip->extcon)) {
|
|
rc = PTR_ERR(chip->extcon);
|
|
dev_err(chip->dev,
|
|
"failed to allocate extcon device rc = %ld\n",
|
|
rc);
|
|
return rc;
|
|
}
|
|
|
|
rc = smb_parse_dt(chip);
|
|
if (rc) {
|
|
dev_err(chip->dev,
|
|
"Couldn't parse DT nodes rc=%d\n", rc);
|
|
return rc;
|
|
}
|
|
|
|
/* i2c pull up regulator configuration */
|
|
if (chip->vcc_i2c) {
|
|
if (regulator_count_voltages(chip->vcc_i2c) > 0) {
|
|
rc = regulator_set_voltage(chip->vcc_i2c,
|
|
SMB_I2C_VTG_MIN_UV, SMB_I2C_VTG_MAX_UV);
|
|
if (rc) {
|
|
dev_err(&client->dev,
|
|
"regulator vcc_i2c set failed, rc = %d\n",
|
|
rc);
|
|
return rc;
|
|
}
|
|
}
|
|
|
|
rc = regulator_enable(chip->vcc_i2c);
|
|
if (rc) {
|
|
dev_err(&client->dev,
|
|
"Regulator vcc_i2c enable failed rc = %d\n",
|
|
rc);
|
|
goto err_set_vtg_i2c;
|
|
}
|
|
}
|
|
|
|
mutex_init(&chip->read_write_lock);
|
|
mutex_init(&chip->path_suspend_lock);
|
|
|
|
/* probe the device to check if its actually connected */
|
|
rc = smb358_read_reg(chip, CHG_OTH_CURRENT_CTRL_REG, ®);
|
|
if (rc) {
|
|
pr_err("Failed to detect SMB358, device absent, rc = %d\n", rc);
|
|
goto err_set_vtg_i2c;
|
|
}
|
|
|
|
i2c_set_clientdata(client, chip);
|
|
|
|
chip->usb_psy_d.name = "usb";
|
|
chip->usb_psy_d.type = POWER_SUPPLY_TYPE_USB;
|
|
chip->usb_psy_d.get_property = smb358_usb_get_property;
|
|
chip->usb_psy_d.set_property = smb358_usb_set_property;
|
|
chip->usb_psy_d.properties = smb358_usb_properties;
|
|
chip->usb_psy_d.num_properties = ARRAY_SIZE(smb358_usb_properties);
|
|
chip->usb_psy_d.property_is_writeable = smb358_usb_is_writeable;
|
|
|
|
usb_psy_cfg.drv_data = chip;
|
|
usb_psy_cfg.supplied_to = smb358_usb_supplicants;
|
|
usb_psy_cfg.num_supplicants = ARRAY_SIZE(smb358_usb_supplicants);
|
|
|
|
chip->usb_psy = devm_power_supply_register(chip->dev,
|
|
&chip->usb_psy_d, &usb_psy_cfg);
|
|
if (IS_ERR(chip->usb_psy)) {
|
|
rc = PTR_ERR(chip->usb_psy);
|
|
dev_err(chip->dev,
|
|
"Unable to register usb_psy rc = %ld\n",
|
|
rc);
|
|
return rc;
|
|
}
|
|
|
|
rc = devm_extcon_dev_register(chip->dev, chip->extcon);
|
|
if (rc) {
|
|
dev_err(chip->dev,
|
|
"failed to register extcon device rc = %ld\n",
|
|
rc);
|
|
return rc;
|
|
}
|
|
|
|
chip->batt_psy_d.name = "battery";
|
|
chip->batt_psy_d.type = POWER_SUPPLY_TYPE_BATTERY;
|
|
chip->batt_psy_d.get_property = smb358_battery_get_property;
|
|
chip->batt_psy_d.set_property = smb358_battery_set_property;
|
|
chip->batt_psy_d.property_is_writeable =
|
|
smb358_batt_property_is_writeable;
|
|
chip->batt_psy_d.properties = smb358_battery_properties;
|
|
chip->batt_psy_d.num_properties = ARRAY_SIZE(smb358_battery_properties);
|
|
chip->batt_psy_d.external_power_changed = smb358_external_power_changed;
|
|
|
|
chip->resume_completed = true;
|
|
mutex_init(&chip->irq_complete);
|
|
|
|
batt_psy_cfg.drv_data = chip;
|
|
batt_psy_cfg.supplied_to = pm_batt_supplied_to;
|
|
batt_psy_cfg.num_supplicants = ARRAY_SIZE(pm_batt_supplied_to);
|
|
chip->batt_psy = devm_power_supply_register(chip->dev,
|
|
&chip->batt_psy_d,
|
|
&batt_psy_cfg);
|
|
if (IS_ERR(chip->batt_psy)) {
|
|
rc = PTR_ERR(chip->batt_psy);
|
|
dev_err(chip->dev,
|
|
"Couldn't register batt psy rc=%ld\n", rc);
|
|
return rc;
|
|
}
|
|
|
|
dump_regs(chip);
|
|
|
|
rc = smb358_regulator_init(chip);
|
|
if (rc) {
|
|
dev_err(&client->dev,
|
|
"Couldn't initialize smb358 ragulator rc=%d\n", rc);
|
|
goto err_set_vtg_i2c;
|
|
}
|
|
|
|
rc = smb358_hw_init(chip);
|
|
if (rc) {
|
|
dev_err(&client->dev,
|
|
"Couldn't initialize hardware rc=%d\n", rc);
|
|
goto err_set_vtg_i2c;
|
|
}
|
|
|
|
rc = determine_initial_state(chip);
|
|
if (rc) {
|
|
dev_err(&client->dev,
|
|
"Couldn't determine initial state rc=%d\n", rc);
|
|
goto err_set_vtg_i2c;
|
|
}
|
|
|
|
/* We will not use it by default */
|
|
if (gpio_is_valid(chip->chg_valid_gpio)) {
|
|
rc = devm_gpio_request(chip->dev,
|
|
chip->chg_valid_gpio,
|
|
"smb358_chg_valid");
|
|
if (rc) {
|
|
dev_err(&client->dev,
|
|
"gpio_request for %d failed rc=%d\n",
|
|
chip->chg_valid_gpio, rc);
|
|
goto err_set_vtg_i2c;
|
|
}
|
|
irq = gpio_to_irq(chip->chg_valid_gpio);
|
|
if (irq < 0) {
|
|
dev_err(&client->dev,
|
|
"Invalid chg_valid irq = %d\n", irq);
|
|
goto err_set_vtg_i2c;
|
|
}
|
|
rc = devm_request_threaded_irq(&client->dev, irq,
|
|
NULL, smb358_chg_valid_handler,
|
|
IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
|
|
"smb358_chg_valid_irq", chip);
|
|
if (rc) {
|
|
dev_err(&client->dev,
|
|
"Failed request_irq irq=%d, gpio=%d rc=%d\n",
|
|
irq, chip->chg_valid_gpio, rc);
|
|
goto err_set_vtg_i2c;
|
|
}
|
|
smb358_chg_valid_handler(irq, chip);
|
|
enable_irq_wake(irq);
|
|
}
|
|
|
|
/* STAT irq configuration */
|
|
if (client->irq) {
|
|
rc = devm_request_threaded_irq(&client->dev,
|
|
client->irq, NULL, smb358_chg_stat_handler,
|
|
IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
|
|
"smb358_chg_stat_irq", chip);
|
|
if (rc) {
|
|
dev_err(&client->dev,
|
|
"Failed STAT irq=%d request rc = %d\n",
|
|
irq, rc);
|
|
goto err_set_vtg_i2c;
|
|
}
|
|
enable_irq_wake(client->irq);
|
|
} else {
|
|
goto err_set_vtg_i2c;
|
|
}
|
|
|
|
smb358_debugfs_init(chip);
|
|
dump_regs(chip);
|
|
dev_info(chip->dev,
|
|
"SMB358 successfully probed. charger=%d, batt_present=%d\n",
|
|
chip->chg_present, smb358_get_prop_batt_present(chip));
|
|
|
|
return 0;
|
|
|
|
err_set_vtg_i2c:
|
|
if (chip->vcc_i2c)
|
|
if (regulator_count_voltages(chip->vcc_i2c) > 0)
|
|
regulator_set_voltage(chip->vcc_i2c, 0,
|
|
SMB_I2C_VTG_MAX_UV);
|
|
return rc;
|
|
}
|
|
|
|
static int smb358_charger_remove(struct i2c_client *client)
|
|
{
|
|
struct smb358_charger *chip = i2c_get_clientdata(client);
|
|
|
|
if (chip->vcc_i2c)
|
|
regulator_disable(chip->vcc_i2c);
|
|
|
|
mutex_destroy(&chip->irq_complete);
|
|
#if defined(CONFIG_DEBUG_FS)
|
|
debugfs_remove_recursive(chip->debug_root);
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
static int smb358_suspend(struct device *dev)
|
|
{
|
|
struct i2c_client *client = to_i2c_client(dev);
|
|
struct smb358_charger *chip = i2c_get_clientdata(client);
|
|
int rc;
|
|
int i;
|
|
|
|
for (i = 0; i < 2; i++) {
|
|
rc = smb358_read_reg(chip, FAULT_INT_REG + i,
|
|
&chip->irq_cfg_mask[i]);
|
|
if (rc)
|
|
dev_err(chip->dev,
|
|
"Couldn't save irq cfg regs rc = %d\n", rc);
|
|
}
|
|
|
|
/* enable wake up IRQs */
|
|
rc = smb358_write_reg(chip, FAULT_INT_REG,
|
|
FAULT_INT_HOT_COLD_HARD_BIT | FAULT_INT_INPUT_UV_BIT);
|
|
if (rc < 0)
|
|
dev_err(chip->dev, "Couldn't set fault_irq_cfg rc = %d\n", rc);
|
|
|
|
rc = smb358_write_reg(chip, STATUS_INT_REG,
|
|
STATUS_INT_LOW_BATT_BIT | STATUS_INT_MISSING_BATT_BIT |
|
|
STATUS_INT_CHGING_BIT | STATUS_INT_INOK_BIT |
|
|
STATUS_INT_OTG_DETECT_BIT | STATUS_INT_CHG_INHI_BIT);
|
|
if (rc < 0)
|
|
dev_err(chip->dev,
|
|
"Couldn't set status_irq_cfg rc = %d\n", rc);
|
|
|
|
mutex_lock(&chip->irq_complete);
|
|
if (chip->vcc_i2c) {
|
|
rc = regulator_disable(chip->vcc_i2c);
|
|
if (rc) {
|
|
dev_err(chip->dev,
|
|
"Regulator vcc_i2c disable failed rc=%d\n", rc);
|
|
mutex_unlock(&chip->irq_complete);
|
|
return rc;
|
|
}
|
|
}
|
|
|
|
chip->resume_completed = false;
|
|
mutex_unlock(&chip->irq_complete);
|
|
return 0;
|
|
}
|
|
|
|
static int smb358_suspend_noirq(struct device *dev)
|
|
{
|
|
struct i2c_client *client = to_i2c_client(dev);
|
|
struct smb358_charger *chip = i2c_get_clientdata(client);
|
|
|
|
if (chip->irq_waiting) {
|
|
pr_err_ratelimited("Aborting suspend, an interrupt was detected while suspending\n");
|
|
return -EBUSY;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static int smb358_resume(struct device *dev)
|
|
{
|
|
struct i2c_client *client = to_i2c_client(dev);
|
|
struct smb358_charger *chip = i2c_get_clientdata(client);
|
|
int rc;
|
|
int i;
|
|
|
|
if (chip->vcc_i2c) {
|
|
rc = regulator_enable(chip->vcc_i2c);
|
|
if (rc) {
|
|
dev_err(chip->dev,
|
|
"Regulator vcc_i2c enable failed rc=%d\n", rc);
|
|
return rc;
|
|
}
|
|
}
|
|
/* Restore IRQ config */
|
|
for (i = 0; i < 2; i++) {
|
|
rc = smb358_write_reg(chip, FAULT_INT_REG + i,
|
|
chip->irq_cfg_mask[i]);
|
|
if (rc)
|
|
dev_err(chip->dev,
|
|
"Couldn't restore irq cfg regs rc=%d\n", rc);
|
|
}
|
|
|
|
mutex_lock(&chip->irq_complete);
|
|
chip->resume_completed = true;
|
|
mutex_unlock(&chip->irq_complete);
|
|
if (chip->irq_waiting) {
|
|
smb358_chg_stat_handler(client->irq, chip);
|
|
enable_irq(client->irq);
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static const struct dev_pm_ops smb358_pm_ops = {
|
|
.suspend = smb358_suspend,
|
|
.suspend_noirq = smb358_suspend_noirq,
|
|
.resume = smb358_resume,
|
|
};
|
|
|
|
static const struct of_device_id smb358_match_table[] = {
|
|
{ .compatible = "qcom,smb358-charger",},
|
|
{ },
|
|
};
|
|
|
|
static const struct i2c_device_id smb358_charger_id[] = {
|
|
{"smb358-charger", 0},
|
|
{},
|
|
};
|
|
MODULE_DEVICE_TABLE(i2c, smb358_charger_id);
|
|
|
|
static struct i2c_driver smb358_charger_driver = {
|
|
.driver = {
|
|
.name = "smb358-charger",
|
|
.owner = THIS_MODULE,
|
|
.of_match_table = smb358_match_table,
|
|
.pm = &smb358_pm_ops,
|
|
},
|
|
.probe = smb358_charger_probe,
|
|
.remove = smb358_charger_remove,
|
|
.id_table = smb358_charger_id,
|
|
};
|
|
|
|
module_i2c_driver(smb358_charger_driver);
|
|
|
|
MODULE_DESCRIPTION("SMB358 Charger");
|
|
MODULE_LICENSE("GPL v2");
|
|
MODULE_ALIAS("i2c:smb358-charger");
|
|
|