kernel_samsung_sm7125/arch/arm64/boot/dts/qcom/sm6150-interposer-trinket-qrd.dtsi

/*
 * Copyright (c) 2018-2019, The Linux Foundation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 and
 * only version 2 as published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 */

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

&pm6125_gpios {
	key_vol_up {
		key_vol_up_default: key_vol_up_default {
			pins = "gpio5";
			function = "normal";
			input-enable;
			bias-pull-up;
			power-source = <0>;
		};
	};
};

&pmi632_gpios {
	smb_en {
		smb_en_default: smb_en_default {
			pins = "gpio2";
			function = "func1";
			output-enable;
		};
	};

	pmi632_sense {
		/* GPIO 7 and 8 are external-sense pins for PMI632 */
		pmi632_sense_default: pmi632_sense_default {
			pins = "gpio7", "gpio8";
			bias-high-impedance;	/* disable the GPIO */
			bias-disable;		/* no-pull */
		};
	};

	pmi632_ctm {
		/* Disable GPIO1 for h/w base mitigation */
		pmi632_ctm_default: pmi632_ctm_default {
			pins = "gpio1";
			bias-high-impedance;	/* disable the GPIO */
			bias-disable;		/* no-pull */
		};
	};
};

&tlmm {
	smb_int_default: smb_int_default {
		mux {
			pins = "gpio21";
			function = "gpio";
		};
		config {
			pins = "gpio21";
			drive-strength = <2>;
			bias-pull-up;
			input-enable;
		};
	};
};

&soc {
	gpio_keys {
		compatible = "gpio-keys";
		label = "gpio-keys";
		pinctrl-names = "default";
		pinctrl-0 = <&key_vol_up_default>;

		vol_up {
			label = "volume_up";
			gpios = <&pm6125_gpios 5 GPIO_ACTIVE_LOW>;
			linux,input-type = <1>;
			linux,code = <KEY_VOLUMEUP>;
			linux,can-disable;
			debounce-interval = <15>;
			gpio-key,wakeup;
		};
	};

	mtp_batterydata: qcom,battery-data {
		qcom,batt-id-range-pct = <15>;
		#include "qg-batterydata-ascent-3450mah.dtsi"
		#include "qg-batterydata-mlp356477-2800mah.dtsi"
	};
};

&qupv3_se1_i2c {
	status = "ok";
	#include "smb1355.dtsi"
};

&smb1355 {
	pinctrl-names = "default";
	pinctrl-0 = <&smb_int_default>;
	interrupt-parent = <&tlmm>;
	interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
	status = "ok";
};

&smb1355_charger {
	pinctrl-names = "default";
	pinctrl-0 = <&smb_en_default &pmi632_sense_default &pmi632_ctm_default>;
	qcom,parallel-mode = <1>;
	qcom,disable-ctm;
	qcom,hw-die-temp-mitigation;
	status = "ok";
};

&pmi632_qg {
	qcom,battery-data = <&mtp_batterydata>;
	qcom,qg-iterm-ma = <100>;
	qcom,hold-soc-while-full;
	qcom,linearize-soc;
};

&pmi632_charger {
	qcom,battery-data = <&mtp_batterydata>;
	qcom,suspend-input-on-debug-batt;
	qcom,sw-jeita-enable;
	/* SMB1355 only */
	qcom,sec-charger-config = <2>;
	dpdm-supply = <&qusb_phy0>;
	qcom,charger-temp-max = <800>;
	qcom,smb-temp-max = <800>;
	qcom,auto-recharge-soc = <98>;
	qcom,flash-disable-soc = <10>;
	qcom,hw-die-temp-mitigation;
	qcom,hw-connector-mitigation;
	qcom,connector-internal-pull-kohm = <100>;
	qcom,thermal-mitigation = <3000000 2500000
			2000000 1500000 1000000 500000>;
};

&qupv3_se1_i2c {
	status = "ok";
	synaptics_tcm@20 {
		compatible = "synaptics,tcm-i2c";
		reg = <0x20>;
		interrupt-parent = <&tlmm>;
		interrupts = <89 0x2008>;
		synaptics,bus-reg-name = "vdd";
		synaptics,pwr-reg-name = "avdd";
		pinctrl-names = "pmx_ts_active","pmx_ts_suspend",
					"pmx_ts_release";
		pinctrl-0 = <&ts_int_active &ts_reset_active>;
		pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
		pinctrl-2 = <&ts_release>;
		synaptics,irq-gpio = <&tlmm 89 0x2008>;
		synaptics,irq-on-state = <0>;
		synaptics,reset-gpio = <&tlmm 88 0x00>;
		synaptics,reset-on-state = <0>;
		synaptics,reset-active-ms = <20>;
		synaptics,reset-delay-ms = <200>;
		synaptics,power-delay-ms = <200>;
		synaptics,ubl-i2c-addr = <0x20>;
		synaptics,y-flip;
	};
};

&pmi632_vadc {
	bat_therm {
		qcom,lut-index = <0>;
	};

	bat_therm_30k {
		qcom,lut-index = <0>;
	};

	bat_therm_400k {
		qcom,lut-index = <0>;
	};
};