You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
429 lines
11 KiB
429 lines
11 KiB
/* Copyright (c) 2018-2019, The Linux Foundation. All rights reserved.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 and
|
|
* only version 2 as published by the Free Software Foundation.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*/
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
|
|
#include <dt-bindings/iio/qcom,spmi-vadc.h>
|
|
#include <dt-bindings/input/input.h>
|
|
#include "sdmmagpie-thermal-overlay.dtsi"
|
|
|
|
#include "sdmmagpie-sde-display.dtsi"
|
|
/*#include "sdmmagpie-camera-sensor-qrd.dtsi"*/
|
|
&soc {
|
|
fpc1020 {
|
|
compatible = "fpc,fpc1020";
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <90 0>;
|
|
fpc,gpio_rst = <&tlmm 91 0x0>;
|
|
fpc,gpio_irq = <&tlmm 90 0>;
|
|
vcc_spi-supply = <&pm6150_l10>;
|
|
vdd_io-supply = <&pm6150_l10>;
|
|
vdd_ana-supply = <&pm6150_l10>;
|
|
fpc,enable-on-boot;
|
|
pinctrl-names = "fpc1020_reset_reset",
|
|
"fpc1020_reset_active",
|
|
"fpc1020_irq_active";
|
|
pinctrl-0 = <&fpc_reset_low>;
|
|
pinctrl-1 = <&fpc_reset_high>;
|
|
pinctrl-2 = <&fpc_int_low>;
|
|
};
|
|
|
|
mtp_batterydata: qcom,battery-data {
|
|
qcom,batt-id-range-pct = <15>;
|
|
#include "qg-batterydata-alium-3600mah.dtsi"
|
|
#include "qg-batterydata-mlp466076-3200mah.dtsi"
|
|
};
|
|
};
|
|
|
|
&qupv3_se7_i2c{
|
|
qcom,i2c-touch-active="st,fts";
|
|
status = "ok";
|
|
st_fts@49 {
|
|
compatible = "st,fts";
|
|
reg = <0x49>;
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <9 0x2008>;
|
|
vdd-supply = <&pm6150_l10>;
|
|
avdd-supply = <&pm6150l_l7>;
|
|
pinctrl-names = "pmx_ts_active", "pmx_ts_suspend";
|
|
pinctrl-0 = <&ts_active>;
|
|
pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
|
|
st,irq-gpio = <&tlmm 9 0x2008>;
|
|
st,reset-gpio = <&tlmm 8 0x00>;
|
|
st,regulator_dvdd = "vdd";
|
|
st,regulator_avdd = "avdd";
|
|
};
|
|
};
|
|
|
|
&tlmm {
|
|
pmx_ts_active {
|
|
ts_active: ts_active {
|
|
mux {
|
|
pins = "gpio8", "gpio9";
|
|
function = "gpio";
|
|
};
|
|
|
|
config {
|
|
pins = "gpio8", "gpio9";
|
|
drive-strength = <8>;
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
};
|
|
|
|
pmx_ts_int_suspend {
|
|
ts_int_suspend: ts_int_suspend {
|
|
mux {
|
|
pins = "gpio9";
|
|
function = "gpio";
|
|
};
|
|
|
|
config {
|
|
pins = "gpio9";
|
|
drive-strength = <2>;
|
|
bias-pull-down;
|
|
};
|
|
};
|
|
};
|
|
|
|
pmx_ts_reset_suspend {
|
|
ts_reset_suspend: ts_reset_suspend {
|
|
mux {
|
|
pins = "gpio8";
|
|
function = "gpio";
|
|
};
|
|
|
|
config {
|
|
pins = "gpio8";
|
|
drive-strength = <2>;
|
|
bias-pull-down;
|
|
};
|
|
};
|
|
};
|
|
|
|
};
|
|
|
|
&qupv3_se8_2uart {
|
|
status = "ok";
|
|
};
|
|
|
|
&qupv3_se3_4uart {
|
|
status = "ok";
|
|
};
|
|
|
|
&pm6150a_amoled {
|
|
status = "ok";
|
|
};
|
|
|
|
&ufsphy_mem {
|
|
compatible = "qcom,ufs-phy-qmp-v3";
|
|
|
|
vdda-phy-supply = <&pm6150_l4>; /* 0.88v */
|
|
vdda-pll-supply = <&pm6150l_l3>; /* 1.2v */
|
|
vdda-phy-max-microamp = <62900>;
|
|
vdda-pll-max-microamp = <18300>;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&ufshc_mem {
|
|
vdd-hba-supply = <&ufs_phy_gdsc>;
|
|
vdd-hba-fixed-regulator;
|
|
vcc-supply = <&pm6150_l19>;
|
|
vcc-voltage-level = <2950000 2960000>;
|
|
vccq2-supply = <&pm6150_l12>;
|
|
vccq2-voltage-level = <1750000 1950000>;
|
|
vcc-max-microamp = <600000>;
|
|
vccq2-max-microamp = <600000>;
|
|
|
|
qcom,vddp-ref-clk-supply = <&pm6150l_l3>;
|
|
qcom,vddp-ref-clk-max-microamp = <100>;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&qupv3_se2_i2c {
|
|
status = "ok";
|
|
qcom,clk-freq-out = <1000000>;
|
|
nq@28 {
|
|
compatible = "qcom,nq-nci";
|
|
reg = <0x28>;
|
|
qcom,nq-irq = <&tlmm 37 0x00>;
|
|
qcom,nq-ven = <&tlmm 12 0x00>;
|
|
qcom,nq-firm = <&tlmm 36 0x00>;
|
|
qcom,nq-clkreq = <&tlmm 31 0x00>;
|
|
qcom,nq-esepwr = <&tlmm 94 0x00>;
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <37 0>;
|
|
interrupt-names = "nfc_irq";
|
|
pinctrl-names = "nfc_active", "nfc_suspend";
|
|
pinctrl-0 = <&nfc_int_active &nfc_enable_active
|
|
&nfc_clk_req_active>;
|
|
pinctrl-1 = <&nfc_int_suspend &nfc_enable_suspend
|
|
&nfc_clk_req_suspend>;
|
|
};
|
|
};
|
|
|
|
&sdhc_1 {
|
|
vdd-supply = <&pm6150_l19>;
|
|
qcom,vdd-voltage-level = <2950000 2950000>;
|
|
qcom,vdd-current-level = <0 570000>;
|
|
|
|
vdd-io-supply = <&pm6150_l12>;
|
|
qcom,vdd-io-always-on;
|
|
qcom,vdd-io-lpm-sup;
|
|
qcom,vdd-io-voltage-level = <1800000 1800000>;
|
|
qcom,vdd-io-current-level = <0 325000>;
|
|
|
|
pinctrl-names = "active", "sleep";
|
|
pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on &sdc1_rclk_on>;
|
|
pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off &sdc1_rclk_off>;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&sdhc_2 {
|
|
vdd-supply = <&pm6150l_l9>;
|
|
qcom,vdd-voltage-level = <2950000 2950000>;
|
|
qcom,vdd-current-level = <0 800000>;
|
|
|
|
vdd-io-supply = <&pm6150l_l6>;
|
|
qcom,vdd-io-voltage-level = <1800000 2950000>;
|
|
qcom,vdd-io-current-level = <0 22000>;
|
|
|
|
pinctrl-names = "active", "sleep";
|
|
pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
|
|
pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
|
|
|
|
cd-gpios = <&tlmm 69 GPIO_ACTIVE_HIGH>;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&dsi_sw43404_amoled_video {
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply_labibb_amoled>;
|
|
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
|
qcom,mdss-dsi-bl-min-level = <1>;
|
|
qcom,mdss-dsi-bl-max-level = <1023>;
|
|
qcom,platform-te-gpio = <&tlmm 10 0>;
|
|
qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
|
|
};
|
|
|
|
&dsi_sw43404_amoled_cmd {
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply_labibb_amoled>;
|
|
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
|
qcom,mdss-dsi-bl-min-level = <1>;
|
|
qcom,mdss-dsi-bl-max-level = <1023>;
|
|
qcom,platform-te-gpio = <&tlmm 10 0>;
|
|
qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
|
|
};
|
|
|
|
&dsi_sw43404_amoled_fhd_plus_cmd {
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply_labibb_amoled>;
|
|
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
|
qcom,mdss-dsi-bl-min-level = <1>;
|
|
qcom,mdss-dsi-bl-max-level = <1023>;
|
|
qcom,platform-te-gpio = <&tlmm 10 0>;
|
|
qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
|
|
};
|
|
|
|
&dsi_sim_cmd {
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply_no_labibb>;
|
|
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
|
qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
|
|
};
|
|
|
|
&dsi_sim_vid {
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply_no_labibb>;
|
|
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
|
qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
|
|
};
|
|
|
|
&dsi_dual_sim_cmd {
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply_no_labibb>;
|
|
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
|
qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
|
|
};
|
|
|
|
&dsi_dual_sim_vid {
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply_no_labibb>;
|
|
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
|
qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
|
|
};
|
|
|
|
&dsi_sim_dsc_375_cmd {
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply_no_labibb>;
|
|
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
|
qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
|
|
};
|
|
|
|
&dsi_dual_sim_dsc_375_cmd {
|
|
qcom,panel-supply-entries = <&dsi_panel_pwr_supply_no_labibb>;
|
|
qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
|
|
qcom,platform-reset-gpio = <&pm6150l_gpios 9 0>;
|
|
};
|
|
|
|
&pm6150_qg {
|
|
qcom,battery-data = <&mtp_batterydata>;
|
|
qcom,qg-iterm-ma = <100>;
|
|
qcom,hold-soc-while-full;
|
|
qcom,linearize-soc;
|
|
qcom,cl-feedback-on;
|
|
};
|
|
|
|
&pm6150_charger {
|
|
io-channels = <&pm6150_vadc ADC_USB_IN_V_16>,
|
|
<&pm6150_vadc ADC_USB_IN_I>,
|
|
<&pm6150_vadc ADC_CHG_TEMP>,
|
|
<&pm6150_vadc ADC_DIE_TEMP>,
|
|
<&pm6150_vadc ADC_SBUx>,
|
|
<&pm6150_vadc ADC_VPH_PWR>;
|
|
io-channel-names = "usb_in_voltage",
|
|
"usb_in_current",
|
|
"chg_temp",
|
|
"die_temp",
|
|
"sbux_res",
|
|
"vph_voltage";
|
|
qcom,battery-data = <&mtp_batterydata>;
|
|
qcom,auto-recharge-soc = <98>;
|
|
qcom,sw-jeita-enable;
|
|
qcom,fcc-stepping-enable;
|
|
qcom,suspend-input-on-debug-batt;
|
|
qcom,sec-charger-config = <1>;
|
|
qcom,thermal-mitigation = <4200000 3500000 3000000
|
|
2500000 2000000 1500000 1000000 500000>;
|
|
dpdm-supply = <&qusb_phy0>;
|
|
qcom,charger-temp-max = <800>;
|
|
qcom,smb-temp-max = <800>;
|
|
};
|
|
|
|
&pm6150_gpios {
|
|
smb_stat {
|
|
smb_stat_default: smb_stat_default {
|
|
pins = "gpio3";
|
|
function = "normal";
|
|
input-enable;
|
|
bias-pull-up;
|
|
qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
|
|
power-source = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&qupv3_se9_i2c {
|
|
status = "ok";
|
|
#include "smb1390.dtsi"
|
|
};
|
|
|
|
&smb1390 {
|
|
/delete-property/ interrupts;
|
|
interrupts = <0x0 0xc2 0x0 IRQ_TYPE_LEVEL_LOW>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&smb_stat_default>;
|
|
status = "ok";
|
|
};
|
|
|
|
&smb1390_charger {
|
|
compatible = "qcom,smb1390-charger-psy";
|
|
io-channels = <&pm6150l_vadc ADC_AMUX_THM2>;
|
|
io-channel-names = "cp_die_temp";
|
|
status = "ok";
|
|
};
|
|
|
|
&pm6150l_gpios {
|
|
key_vol_up {
|
|
key_vol_up_default: key_vol_up_default {
|
|
pins = "gpio2";
|
|
function = "normal";
|
|
input-enable;
|
|
bias-pull-up;
|
|
power-source = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&soc {
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
label = "gpio-keys";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&key_vol_up_default>;
|
|
|
|
vol_up {
|
|
label = "volume_up";
|
|
gpios = <&pm6150l_gpios 2 GPIO_ACTIVE_LOW>;
|
|
linux,input-type = <1>;
|
|
linux,code = <KEY_VOLUMEUP>;
|
|
linux,can-disable;
|
|
debounce-interval = <15>;
|
|
gpio-key,wakeup;
|
|
};
|
|
};
|
|
};
|
|
|
|
&qusb_phy0 {
|
|
qcom,qusb-phy-init-seq =
|
|
/* <value reg_offset> */
|
|
<0x23 0x210 /* PWR_CTRL1 */
|
|
0x03 0x04 /* PLL_ANALOG_CONTROLS_TWO */
|
|
0x7c 0x18c /* PLL_CLOCK_INVERTERS */
|
|
0x80 0x2c /* PLL_CMODE */
|
|
0x0a 0x184 /* PLL_LOCK_DELAY */
|
|
0x19 0xb4 /* PLL_DIGITAL_TIMERS_TWO */
|
|
0x40 0x194 /* PLL_BIAS_CONTROL_1 */
|
|
0x20 0x198 /* PLL_BIAS_CONTROL_2 */
|
|
0x21 0x214 /* PWR_CTRL2 */
|
|
0x00 0x220 /* IMP_CTRL1 */
|
|
0x18 0x224 /* IMP_CTRL2 */
|
|
0x37 0x240 /* TUNE1 */
|
|
0x29 0x244 /* TUNE2 */
|
|
0xca 0x248 /* TUNE3 */
|
|
0x04 0x24c /* TUNE4 */
|
|
0x03 0x250 /* TUNE5 */
|
|
0x00 0x23c /* CHG_CTRL2 */
|
|
0x22 0x210>; /* PWR_CTRL1 */
|
|
|
|
qcom,qusb-phy-host-init-seq =
|
|
/* <value reg_offset> */
|
|
<0x23 0x210 /* PWR_CTRL1 */
|
|
0x03 0x04 /* PLL_ANALOG_CONTROLS_TWO */
|
|
0x7c 0x18c /* PLL_CLOCK_INVERTERS */
|
|
0x80 0x2c /* PLL_CMODE */
|
|
0x0a 0x184 /* PLL_LOCK_DELAY */
|
|
0x19 0xb4 /* PLL_DIGITAL_TIMERS_TWO */
|
|
0x40 0x194 /* PLL_BIAS_CONTROL_1 */
|
|
0x20 0x198 /* PLL_BIAS_CONTROL_2 */
|
|
0x21 0x214 /* PWR_CTRL2 */
|
|
0x00 0x220 /* IMP_CTRL1 */
|
|
0x18 0x224 /* IMP_CTRL2 */
|
|
0x37 0x240 /* TUNE1 */
|
|
0x29 0x244 /* TUNE2 */
|
|
0xca 0x248 /* TUNE3 */
|
|
0x04 0x24c /* TUNE4 */
|
|
0x03 0x250 /* TUNE5 */
|
|
0x00 0x23c /* CHG_CTRL2 */
|
|
0x22 0x210>; /* PWR_CTRL1 */
|
|
};
|
|
|
|
&fsa4480 {
|
|
status = "disabled";
|
|
};
|
|
|
|
&sde_dp {
|
|
pinctrl-names = "mdss_dp_active", "mdss_dp_sleep";
|
|
pinctrl-0 = <&sde_dp_aux_active &sde_dp_usbplug_cc_active>;
|
|
pinctrl-1 = <&sde_dp_aux_suspend &sde_dp_usbplug_cc_suspend>;
|
|
qcom,aux-en-gpio = <&tlmm 42 0>;
|
|
qcom,aux-sel-gpio = <&tlmm 33 0>;
|
|
qcom,dp-gpio-aux-switch;
|
|
};
|
|
|