You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
142 lines
5.6 KiB
142 lines
5.6 KiB
SD and MMC Block Device Attributes
|
|
==================================
|
|
|
|
These attributes are defined for the block devices associated with the
|
|
SD or MMC device.
|
|
|
|
The following attributes are read/write.
|
|
|
|
force_ro Enforce read-only access even if write protect switch is off.
|
|
|
|
num_wr_reqs_to_start_packing This attribute is used to determine
|
|
the trigger for activating the write packing, in case the write
|
|
packing control feature is enabled.
|
|
|
|
When the MMC manages to reach a point where num_wr_reqs_to_start_packing
|
|
write requests could be packed, it enables the write packing feature.
|
|
This allows us to start the write packing only when it is beneficial
|
|
and has minimum affect on the read latency.
|
|
|
|
The number of potential packed requests that will trigger the packing
|
|
can be configured via sysfs by writing the required value to:
|
|
/sys/block/<block_dev_name>/num_wr_reqs_to_start_packing.
|
|
|
|
The default value of num_wr_reqs_to_start_packing was determined by
|
|
running parallel lmdd write and lmdd read operations and calculating
|
|
the max number of packed writes requests.
|
|
|
|
SD and MMC Device Attributes
|
|
============================
|
|
|
|
All attributes are read-only.
|
|
|
|
cid Card Identification Register
|
|
csd Card Specific Data Register
|
|
scr SD Card Configuration Register (SD only)
|
|
date Manufacturing Date (from CID Register)
|
|
fwrev Firmware/Product Revision (from CID Register) (SD and MMCv1 only)
|
|
hwrev Hardware/Product Revision (from CID Register) (SD and MMCv1 only)
|
|
manfid Manufacturer ID (from CID Register)
|
|
name Product Name (from CID Register)
|
|
oemid OEM/Application ID (from CID Register)
|
|
prv Product Revision (from CID Register) (SD and MMCv4 only)
|
|
serial Product Serial Number (from CID Register)
|
|
erase_size Erase group size
|
|
preferred_erase_size Preferred erase size
|
|
raw_rpmb_size_mult RPMB partition size
|
|
rel_sectors Reliable write sector count
|
|
ocr Operation Conditions Register
|
|
dsr Driver Stage Register
|
|
cmdq_en Command Queue enabled: 1 => enabled, 0 => not enabled
|
|
|
|
Note on Erase Size and Preferred Erase Size:
|
|
|
|
"erase_size" is the minimum size, in bytes, of an erase
|
|
operation. For MMC, "erase_size" is the erase group size
|
|
reported by the card. Note that "erase_size" does not apply
|
|
to trim or secure trim operations where the minimum size is
|
|
always one 512 byte sector. For SD, "erase_size" is 512
|
|
if the card is block-addressed, 0 otherwise.
|
|
|
|
SD/MMC cards can erase an arbitrarily large area up to and
|
|
including the whole card. When erasing a large area it may
|
|
be desirable to do it in smaller chunks for three reasons:
|
|
1. A single erase command will make all other I/O on
|
|
the card wait. This is not a problem if the whole card
|
|
is being erased, but erasing one partition will make
|
|
I/O for another partition on the same card wait for the
|
|
duration of the erase - which could be a several
|
|
minutes.
|
|
2. To be able to inform the user of erase progress.
|
|
3. The erase timeout becomes too large to be very
|
|
useful. Because the erase timeout contains a margin
|
|
which is multiplied by the size of the erase area,
|
|
the value can end up being several minutes for large
|
|
areas.
|
|
|
|
"erase_size" is not the most efficient unit to erase
|
|
(especially for SD where it is just one sector),
|
|
hence "preferred_erase_size" provides a good chunk
|
|
size for erasing large areas.
|
|
|
|
For MMC, "preferred_erase_size" is the high-capacity
|
|
erase size if a card specifies one, otherwise it is
|
|
based on the capacity of the card.
|
|
|
|
For SD, "preferred_erase_size" is the allocation unit
|
|
size specified by the card.
|
|
|
|
"preferred_erase_size" is in bytes.
|
|
|
|
Note on raw_rpmb_size_mult:
|
|
"raw_rpmb_size_mult" is a multiple of 128kB block.
|
|
RPMB size in byte is calculated by using the following equation:
|
|
RPMB partition size = 128kB x raw_rpmb_size_mult
|
|
|
|
SD/MMC/SDIO Clock Gating Attribute
|
|
==================================
|
|
|
|
Read and write access is provided to following attribute.
|
|
This attribute appears only if CONFIG_MMC_CLKGATE is enabled.
|
|
|
|
clkgate_delay Tune the clock gating delay with desired value in milliseconds.
|
|
|
|
echo <desired delay> > /sys/class/mmc_host/mmcX/clkgate_delay
|
|
|
|
SD/MMC/SDIO Clock Scaling Attributes
|
|
====================================
|
|
|
|
Read and write accesses are provided to following attributes.
|
|
|
|
polling_interval Measured in milliseconds, this attribute
|
|
defines how often we need to check the card
|
|
usage and make decisions on frequency scaling.
|
|
|
|
up_threshold This attribute defines what should be the
|
|
average card usage between the polling
|
|
interval for the mmc core to make a decision
|
|
on whether it should increase the frequency.
|
|
For example when it is set to '35' it means
|
|
that between the checking intervals the card
|
|
needs to be on average more than 35% in use to
|
|
scale up the frequency. The value should be
|
|
between 0 - 100 so that it can be compared
|
|
against load percentage.
|
|
|
|
down_threshold Similar to up_threshold, but on lowering the
|
|
frequency. For example, when it is set to '2'
|
|
it means that between the checking intervals
|
|
the card needs to be on average less than 2%
|
|
in use to scale down the clocks to minimum
|
|
frequency. The value should be between 0 - 100
|
|
so that it can be compared against load
|
|
percentage.
|
|
|
|
enable Enable clock scaling for hosts (and cards)
|
|
that support ultrahigh speed modes
|
|
(SDR104, DDR50, HS200).
|
|
|
|
echo <desired value> > /sys/class/mmc_host/mmcX/clk_scaling/polling_interval
|
|
echo <desired value> > /sys/class/mmc_host/mmcX/clk_scaling/up_threshold
|
|
echo <desired value> > /sys/class/mmc_host/mmcX/clk_scaling/down_threshold
|
|
echo <desired value> > /sys/class/mmc_host/mmcX/clk_scaling/enable |