/*
 * Copyright (c) 2019, The Linux Foundation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 and
 * only version 2 as published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 */

&soc {
	ir_led: camera-ir-led@0 {
		cell-index = <0>;
		reg = <0x00>;
		compatible = "qcom,camera-ir-led";
		pwms = <&pm6150l_pwm_1  0 0>;
		enable-active-high;
		pinctrl-names = "default", "cam_default", "cam_suspend";
		pinctrl-0 = <&irled_pwm>;
		pinctrl-1 = <&cam_sensor_ir_cut_on>;
		pinctrl-2 = <&cam_sensor_ir_cut_off>;
		gpios = <&tlmm 73 0>,
			<&tlmm 74 0>;
		qcom,gpio-ir-p = <0>;
		qcom,gpio-ir-m =  <1>;
		qcom,gpio-req-tbl-num = <0 1>;
		qcom,gpio-req-tbl-flags = <0 0>;
		qcom,gpio-req-tbl-label = "IR_CUT_FILTER_P",
				"IR_CUT_FILTER_M";
		gpio-no-mux = <0>;
		status = "ok";
	};

	camera_ldo: gpio-regulator@0 {
		compatible = "regulator-fixed";
		reg = <0x00 0x00>;
		regulator-name = "camera_ldo";
		regulator-min-microvolt = <1200000>;
		regulator-max-microvolt = <1200000>;
		regulator-enable-ramp-delay = <135>;
		enable-active-high;
		gpio = <&pm6150l_gpios 3 0>;
		pinctrl-names = "default";
		pinctrl-0 = <&cam_sensor_dvdd_en>;
		vin-supply = <&pm6150l_s8>;
	};
};

&cam_cci {
	qcom,cam-res-mgr {
		compatible = "qcom,cam-res-mgr";
		status = "ok";
	};

	qcom,cam-sensor@0 {
		cell-index = <0>;
		compatible = "qcom,cam-sensor";
		reg = <0x0>;
		csiphy-sd-index = <0>;
		sensor-position-roll = <90>;
		sensor-position-pitch = <0>;
		sensor-position-yaw = <180>;
		cam_vio-supply = <&pm6150_l13>;
		cam_vana-supply = <&pm6150l_l4>;
		cam_vdig-supply = <&camera_ldo>;
		cam_clk-supply = <&titan_top_gdsc>;
		ir-led-src = <&ir_led>;
		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
			"cam_clk";
		rgltr-cntrl-support;
		rgltr-min-voltage = <1800000 2850000 1200000 0>;
		rgltr-max-voltage = <1800000 2850000 1200000 0>;
		rgltr-load-current = <0 80000 105000 0>;
		gpio-no-mux = <0>;
		pinctrl-names = "cam_default", "cam_suspend";
		pinctrl-0 = <&cam_sensor_mclk0_active
				&cam_sensor_rear_active>;
		pinctrl-1 = <&cam_sensor_mclk0_suspend
				&cam_sensor_rear_suspend>;
		gpios = <&tlmm 28 0>,
			<&tlmm 47 0>;
		gpio-reset = <1>;
		gpio-req-tbl-num = <0 1>;
		gpio-req-tbl-flags = <1 0>;
		gpio-req-tbl-label = "CAMIF_MCLK0",
					"CAM_RESET0";
		sensor-mode = <0>;
		cci-master = <0>;
		status = "ok";
		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
		clock-names = "cam_clk";
		clock-cntl-level = "turbo";
		clock-rates = <37125000>;
	};
};