Add definition for high-speed MMC/SD device and add to SMDK2443
device list.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change the name of the S3C2443_SDI1 to S3C2443_HSMMC to ensure
that it is correctly identified.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need valid_phys_addr_range() or valid_mmap_phys_addr_range()
for the !CONFIG_MMU case.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Presently, we check for the minimum ARM architecture that we're
building for to determine whether we need ASID support. This is
wrong - if we're going to support a range of CPUs which include
ARMv6 or higher, we need the ASID.
Convert the checks to use a new configuration symbol, and arrange
for ARMv6 and higher CPU entries to select it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add utimensat, signalfd, timerfd, eventfd syscalls. Add ignore
defines for sync_file_range and fadvise64_64 which we implement
differently.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change the SPI Channel 1 register offset in s3c_spi1_resource[], and
s3c2412_dma_mappings[]. Offset has to be 0x100 in s3c2412/13's case.
Also, total SPI memory resource size changed to 0x24 for s3c2412/13.
Signed-off-by: Sandeep Patil <psandeep.s@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Integrator/CP SMP platform support was never fully merged, and now
it's causing build breakage. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
it depends on elimination of unreachable branches in switch (by object
size), so we must declare it always_inline
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ide_use_dma() duplicates a lot of ide_max_dma_mode() functionality
and as all users of ide_use_dma() were converted to use ide_tune_dma()
now it is possible to add missing checks to ide_tune_dma() and remove
ide_use_dma() completely, so do it.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* check ->speedproc return value in ide_tune_dma()
* use ide_tune_dma() in cmd64x/cs5530/sc1200/siimage/sl82c105/scc_pata drivers
* remove no longer needed ide_dma_enable()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Take MAX_ORDER into consideration when determining KMALLOC_SHIFT_HIGH.
Otherwise we may run into a situation where we attempt to create general
slabs larger than MAX_ORDER.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several parts of kernel/smp.c and smpboot.c are generally useful for other
subarchitectures and paravirt_ops implementations, so make them available for
reuse.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After examining what was checked in and the code base I discovered that most
of 86c0baf123 wasn't necessary anymore....
So here's a patch that reverts the last part of that changeset:
Revert part of 86c0baf123.
The kernel has moved forward to a state where the original change is not
necessary. After porting forward, this final version of the patch was
applied and broke non-x86 architectures.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
m68k: implement __clear_user(), which is needed by fs/signalfd.c
Since we always let the MMU do all checking, clear_user() and __clear_user()
are identical. The old clear_user() is renamed to __clear_user() for
consistency.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"Remove hardcoding of hard_smp_processor_id on UP systems",
2f4dfe206a in Linus' tree, moved
the definition of hard_smp_processor_id linux/smp.h to asm/smp.h
for UP systems. This causes a regression on Alpha.
cc1: warnings being treated as errors
arch/alpha/kernel/setup.c: In function 'setup_arch':
arch/alpha/kernel/setup.c:506: warning: implicit declaration of function 'hard_smp_processor_id'
make[1]: *** [arch/alpha/kernel/setup.o] error 1
make: *** [arch/alpha/kernel] error 2
By including asm/smp.h non-conditionally in asm/mmu_context.h
the problem appears to be resolved.
Cc: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Simon Horman <horms@verge.net.au>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lib/ioremap.c is presently only built in if CONFIG_MMU is set. While this
is reasonable, platforms that support both CONFIG_MMU=y or n need to be
able to call in to this regardless.
As none of the current nommu platforms do anything special with ioremap(),
we assume that it's always successful.
This fixes the SH-4 build with CONFIG_MMU=n.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit f64da958df.
Andi Kleen is unhappy with the changes, and they really do not seem
worth it. IPMI could use DIE_NMI_IPI instead of the new callback, even
though that ends up having its own set of problems too, mainly because
the IPMI code cannot really know the NMI was from IPMI or not.
Manually fix up conflicts in arch/x86_64/kernel/traps.c and
drivers/char/ipmi/ipmi_watchdog.c.
Cc: Andi Kleen <ak@suse.de>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Corey Minyard <minyard@acm.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
compat_sys_signalfd and compat_sys_timerfd need declarations before
PowerPC can wire them up.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch was hanging around for some time while we were waiting
for the compiler situation to improve.. now that all is well again,
finally merge it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
A few interrupt handlers were never updated, fix them up.
We were missing the irq_regs conversion also, so do that
at the same time.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This has suffered a bit of bitrot, so we're a bit behind on the
syscalls. There were a few that were wrapped incorrectly as well,
caught by the syscall checker. Fix them all up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
there is a wrong id in drivers/char/agp/via-agp.c
#define PCI_DEVICE_ID_VIA_CX700 0x8324
It must be 0x0324
Notice that PCI_DEVICE_ID_VIA_CX700 is also used in
drivers/i2c/busses/i2c-viapro.c and
drivers/ide/pci/via82cxxx.c
So, I think that constant must be renamed to avoid conflicting.
I attached a proposed patch.
Signed-off-by: Dave Jones <davej@redhat.com>
Adding tabs where spaces currently are.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SLUB cannot run on i386 at this point because i386 uses the page->private and
page->index field of slab pages for the pgd cache.
Make SLUB run on i386 by replacing the pgd slab cache with a quicklist.
Limit the changes as much as possible. Leave the improvised linked list in place
etc etc. This has been working here for a couple of weeks now.
Acked-by: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the new get_irqnr_preamble macro to move the address of the IRQ
controller outside the IRQ handling loop.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Besides those modes in ATI SB600 SATA controller, ATI SB700 supports one
more mode:the combined mode.
The combined mode is a Legacy IDE mode used for compatibility with some old
OS without AHCI driver, but now it is not necessary for Linux since the
kernel has supported AHCI.
Signed-off-by: Luugi Marsan <luugi.marsan@amd.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ACPI applies to both SATA and PATA. Drop the 'S' from the config
variable.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata enables SCSI host during ATA host activation which happens
after IRQ handler is registered and IRQ is enabled. All ATA ports are
in frozen state when IRQ is enabled but frozen ports may raise limited
number of IRQs after being frozen - IOW, ->freeze() is not responsible
for clearing pending IRQs. During normal operation, the IRQ handler
is responsible for clearing spurious IRQs on frozen ports and it
usually doesn't require any extra code.
Unfortunately, during host initialization, the IRQ handler can end up
scheduling EH for a port whose SCSI host isn't initialized yet. This
results in OOPS in the SCSI midlayer. This is relatively short window
and scheduling EH for probing is the first thing libata does after
initialization, so ignoring EH scheduling until initialization is
complete solves the problem nicely.
This problem was spotted by Berck E. Nash in the following thread.
http://thread.gmane.org/gmane.linux.kernel/519412
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Berck E. Nash <flyboy@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The intention of using port_mask in SFF init helpers was to eventually
support exoctic configurations such as combination of legacy and
native port on the same controller. This never became actually
necessary and the related code always has been subtly broken one way
or the other. Now that new init model is in place, there is no reason
to make common helpers capable of handling all corner cases. Exotic
cases can simply dealt within LLDs as necessary.
This patch removes port_mask handling in SFF init helpers. SFF init
helpers don't take n_ports argument and interpret it into port_mask
anymore. All information is carried via port_info. n_ports argument
is dropped and always two ports are allocated. LLD can tell SFF to
skip certain port by marking it dummy. Note that SFF code has been
treating unuvailable ports this way for a long time until recent
breakage fix from Linus and is consistent with how other drivers
handle with unavailable ports.
This fixes 1-port legacy host handling still broken after the recent
native mode fix and simplifies SFF init logic. The following changes
are made...
* ata_pci_init_native_host() and ata_init_legacy_host() both now try
to initialized whatever they can and mark failed ports dummy. They
return 0 if any port is successfully initialized.
* ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't
take n_ports argument. All info should be specified via port_info
array. Always two ports are allocated.
* ata_pci_init_bmdma() exported to be used by LLDs in exotic cases.
* port_info handling in all LLDs are standardized - all port_info
arrays are const stack variable named ppi. Unless the second port
is different from the first, its port_info is specified as NULL
(tells libata that it's identical to the last non-NULL port_info).
* pata_hpt37x/hpt3x2n: don't modify static variable directly. Make an
on-stack copy instead as ata_piix does.
* pata_uli: It has 4 ports instead of 2. Don't use
ata_pci_prepare_native_host(). Allocate the host explicitly and use
init helpers. It's simple enough.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement suspend/resume support using sdev->manage_start_stop.
* Device suspend/resume is now SCSI layer's responsibility and the
code is simplified a lot.
* DPM is dropped. This also simplifies code a lot. Suspend/resume
status is port-wide now.
* ata_scsi_device_suspend/resume() and ata_dev_ready() removed.
* Resume now has to wait for disk to spin up before proceeding. I
couldn't find easy way out as libata is in EH waiting for the
disk to be ready and sd is waiting for EH to complete to issue
START_STOP.
* sdev->manage_start_stop is set to 1 in ata_scsi_slave_config().
This fixes spindown on shutdown and suspend-to-disk.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A driver for the KS8695 internal UART.
Based on the 2.6.9 driver from Micrel.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add core support for the Kendin/Micrel KS8695 processor family.
It is an ARM922-T based SoC with integrated USART, 4-port Ethernet
Switch, WAN Ethernet port, and optional PCI Host bridge, etc.
http://www.micrel.com/page.do?page=product-info/sys_on_chip.jsp
This patch is based on earlier patches from Lennert Buytenhek, Ben
Dooks and Greg Ungerer posted to the arm-linux-kernel mailing list in
March 2006; and Micrel's 2.6.9 port.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define SZ_512, SZ_256 and SZ_16 in asm-arm/sizes.h.
Remove the definitions from the at91*_devices.c files.
(Dependent on ARM patch #4370/2)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for Atmel's new AT91SAM9RL range of processors.
Includes similar peripherals as other AT91SAM9 processors, but with a
High-speed USB controller and various sizes of internal SRAM.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
> -** Copyright 1994 by Bj<94>rn Brauel
> +** Copyright 1994 by Bj”rn Brauel
I think these were cp437, and it should read 'Björn'.
(asm-m68k/atari*.h)
Also note that Arnaldo just put more legacy noise into CREDITS...
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Enable devices to signal interrupts via PCI memory cycles.
rev6:
* fix enable/disable typo, Michael Ellerman
rev5:
* fix up ack, enable, and disable for iop13xx_msi_chip
rev4:
* move smp compile fix to separate patch
* use dynamic_irq_init in create_irq()
* hookup mask/unmask routines in iop13xx_msi_chip
rev3:
* change msi.c to use linux/smp.h instead of asm/smp.h
* call dynamic_irq_cleanup at destroy_irq time
rev2:
* destroy_irq did not take the full 128 bits of msi_irq_in_use into account
* added missing '&' for calls to test_and_set_bit and clear_bit
[ebiederm@xmission.com: review comments/suggestions]
[dan.j.williams@intel.com: cleanups/forward port to 2.6-git]
Signed-off-by: Daniel Wolstenholme <daniel.e.wolstenholme@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IA64 is the origin of the quicklist implementation. So cut out the pieces
that are now in core code and modify the functions called.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
In case of reentrance i.e when a probe handler calls a functions which
inturn has a probe, we save a previous kprobe information and just single
step the reentrant probe without calling the actual probe handler. During
this reentracy period, if an interrupt occurs and if probe happens to
trigger in the inturrupt path, then we were corrupting the previous kprobe(
as we were overriding the previous kprobe info) info their by crashing the
system. This patch fixes this issues by having a an array of previous
kprobe info struct(with the array size of 2).
This similar technique is not needed on i386 and x86_64 because by default
interrupts are turn off in the break/int3 exception handler.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
On SN, only allow one bit to be set in the smp_affinty mask when
redirecting an interrupt. Currently setting multiple bits is allowed, but
only the first bit is used in determining the CPU to redirect to. This has
caused confusion among some customers.
[akpm@linux-foundation.org: fixes]
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add base kernel support for the TI DaVinci platform.
This patch only includes interrupts, timers, CPU identification,
serial support and basic power and sleep controller init. More
drivers to come.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mariusz Kozlowski