I introduced this way back in 2.6.13 when adding the port lock logic.
This device talks out through different "ports" all at the same time, so
the lock logic was wrong, preventing any data from ever being sent
properly.
Thanks a lot to Bernhard Reiter <bernhard@intevation.de> for being
patient and helping with debugging this.
Cc: Bernhard Reiter <bernhard@intevation.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on Simon's original driver, with some minor code cleanups and
tidying by me.
Cc: Simon Schulz <simon@auctionant.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If serial_open() fails at the port assignment or mutex_lock_interruptible()
is interrupted, the 'serial' object will never be freed.
We should call kref_put() when those errors happens.
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the device is disconnected while serial_open() is executing and
either try_module_get() or the device specific open function fails, the
kref_put() call in the 'bailout_kref_put' label will free the memory
pointed out by 'port'.
The subsequent dereferences in the 'bailout_kref_put' label will be
invalid.
The fix is just to assure kref_put() is called after any 'port' usage.
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's become apparent as machines get faster that the emagic kernel firmware
loaders (based on the ezusb loader) have a reset race. a 400MHz TiBook
never tripped it, but a 2GHz Pentium M seems to hit it about 30% of the
time. The bug is seen as a hung USB box and the kernel error:
drivers/usb/misc/emi62.c: emi62_load_firmware - error loading firmware:
error = -110
The patch below inserts a delay after deasserting reset to allow the box to
settle before a new command is issued. This affects only device startup.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After recent changes, the USB keyboard as shipped with IBM pSeries systems
does not work anymore, unless the keyboard is replugged after reboot.
Adding this model to the blacklist fixes it.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the Sierra Wireless card to airprime.c.
I tested this on my laptop.
Signed-off-by: Ken Brush <ken@cgi101.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Addresses for ioremap must be calculated off of pci_resource_start;
we can't directly use the bus address as seen by the HCA. Fix the
code that remaps device memory for FMR access.
Based on patch by Klaus Smolin.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
661FX7MI-S motherboard which uses the SiS 661FX chipset. The patch adds
an entry to mii_chip_info for the transceiver.
The PHY ids were found using the sis900_c_122.diff patch from
http://brownhat.org/sis900.html but that patch didn't solve the problem,
because the PHY at address 1 was already being chosen.
Without my patch, when bursts of packets arrive from other hosts on a
LAN, the interface dropped one roughly 10% of the time, causing
retransmits. There were fifth second pauses in refresh of large xterms,
and it made Netrek suck. I can provide further test data.
Workaround in lieu of patch is to use mii-tool to advertise
100baseTx-HD, then force renegotiation.
I wasn't able to identify the actual transceiver, so the description
field is a guess.
This patch is similar to Artur Skawina's patch:
http://marc.theaimsgroup.com/?l=linux-netdev&m=114297516729079&w=2
I'm not sure, but I wonder if it means the default behaviour should be
changed, so as to better handle future transceivers.
Diff is against 2.6.16.13.
Signed-off-by: James Cameron <james.cameron@hp.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
make sure phy_map entries whose PHY address is masked are initialized
to NULL, given that other code (such as mdiobus_unregister for
instance) assumes that non-NULL phy_map entries are allocated
phy_devices
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Bringing down a port also masks off the status and other IRQ's
needed for device to function due to missing paren's.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
This patch corrects the order of the calls to register_chrdev() and
pcmcia_register_driver(). Now udev correctly creates userspace device
files /dev/cmmN and /dev/cmxN respectively.
Based on an earlier patch by Jan Niehusmann <jan@gondor.com>.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A race condition exists in mptfc between the thread registering a device
with the fc transport and the scan work generated by the transport.
This race existed prior to the application of the mptfc bug fix patch.
mptfc_register_dev() calls fc_remote_port_add() with the FC_RPORT_ROLE_TARGET
bit set in the rport ids passed to the function. Having this bit set causes
fc_remote_port_add() to schedule a scan of the device.
This scan can execute before mptfc_register_dev() can fill in the dd_data
in the rport structure. When this happens, mptfc_target_alloc() will fail
because dd_data is null.
Attached is a patch which fixes the problem. The patch changes the rport ids
passed to fc_remote_port_add() to not have the TARGET bit set. This prevents
the scan from being scheduled. After mptfc_register_dev() fills in the rport
dd_data field, fc_remote_port_rolechg() is called, changing the role of the
rport to TARGET. Thus, the scan is scheduled after dd_data is filled
in which prevents the failure in mptfc_target_alloc().
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
tg3_run_loopback doesn't check that dev_alloc_skb() returns anything
useful.
Even if dev_alloc_skb() fails to return an skb to us we'll happily go
on and assume it did, so we risk dereferencing a NULL pointer. Much
better to fail gracefully by returning -ENOMEM than crashing here.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deleting a child interface with a non-default P_Key via
/sys/class/net/ibX/delete_child, the interface must be freed with
free_netdev() (rather than kfree() on the private data).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since sir_kthread.c pretty much duplicates the workqueue
functionality, we'd better switch. The SIR fsm has been merged into
sir_dev.c and thus sir_kthread.c is deleted.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minimal PNP hotplug support for the smsc-ircc2 driver. A modular
driver will be modprobed via hotplug, but still bypasses driver model
probing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a fix for the CS5535 errata 111:
When the SMBus controller tries to access a non-existing device, it sets
the NEGACK bit, SMBus I/O offset 01h[4], to 1 after it detects no
acknowledge at the ninth clock. The specification states that the bit
can be cleared by writing a 1 to it, but under certain circumstances it
is possible for this bit to not clear.
Writing a 0 to the bit resets the internal state machine and clears the
issue.
Since all writable bits in ACBST are W1C bits (write-one-to-clear) the
second write doesn't affect any other logic except the buggy NEGACK
state machine. The second write clears an internal register which is
responsible for "overwriting" the NEGACK bit in ACBST.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can't pass a string on the stack to request_region. As soon as we
leave the function that stack is gone and the string is lost. Let's
use the same string we identify the i2c_adapter with instead, it's
more simple, more consistent, and just works.
This is the second half of fix to bug #6445.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The scx200_acb driver shouldn't return failure after initialization
if it successfully registered at least one i2c_adapter, else we are
leaking resources. The driver was OK in that respect up to 2.6.16, a
recent change broke it.
This is part of the fix to bug #6445.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix races in in destroying various objects. If a destroy routine
waits for an object to become free by doing
wait_event(&obj->wait, !atomic_read(&obj->refcount));
/* now clean up and destroy the object */
and another place drops a reference to the object by doing
if (atomic_dec_and_test(&obj->refcount))
wake_up(&obj->wait);
then this is susceptible to a race where the wait_event() and final
freeing of the object occur between the atomic_dec_and_test() and the
wake_up(). And this is a use-after-free, since wake_up() will be
called on part of the already-freed object.
Fix this in mthca by replacing the atomic_t refcounts with plain old
integers protected by a spinlock. This makes it possible to do the
decrement of the reference count and the wake_up() so that it appears
as a single atomic operation to the code waiting on the wait queue.
While touching this code, also simplify mthca_cq_clean(): the CQ being
cleaned cannot go away, because it still has a QP attached to it. So
there's no reason to be paranoid and look up the CQ by number; it's
perfectly safe to use the pointer that the callers already have.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a SCSI abort completes, or the command completes successfully, then
the driver must remove the command from its queue of pending
commands. Similarly, if a device reset succeeds, then all commands
queued for the given device must be removed from the queue.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code to display local_link_integrity_errors and
excessive_buffer_overrun_errors in
/sys/class/infiniband/<hca>/ports/<n>/counters/
uses the wrong shift to extract the 4 bit values.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds support for ACG Identification Technologies GmbH's HF
Dual ISO Reader (an RFID tag reader) to the ftdi_sio driver's device ID
table. The product ID was supplied by anotonios (anton at goto10 dot
org) on the ftdi-usb-sio-devel list and subsequently verified by myself
(Ian Abbott).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In kernel 2.6.16, if a mounted storage device is removed, an oops happens
because ub supplies an interface device (and kobject) to the block layer,
but neglects to pin it. And apparently, the block layer expects its users
to pin device structures.
The code in ub was broken this way for years. But the bug was exposed only
by 2.6.16 when it started to call block_uevent on close, which traverses
device structures (kobjects actually).
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The choose_configuration() routine contains code the determine the
device's power source, so that configurations requiring external power
can be ruled out if the device is running on bus power. Unfortunately
it turns out that some devices have errors in their config descriptors
and other devices don't like the GET_DEVICE_STATUS request.
Since that information wasn't used for anything else, this patch (as673)
removes the code, leaving only a comment. It fixes bugzilla entry
#6448.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a small regression in USB controller power usage for many
OHCI controllers, notably including every non-PCI version of OHCI: on
those systems, the runtime autosuspend mechanism is no longer enabled.
The change moves to saner defaults. All root hubs are expected to handle
remote wakeup (and hence autosuspend), although drivers for buggy silicon
may override that default.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Teach "pegasus" to handle a few of the disconnect fault paths
without hundreds of usless syslog messages.
Handle the carrier check workqueue entry even if the driver has
not been opened.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because of the way stringify works, using an expression
like 64 * 1024 for UDSL_MAX_BUF_SIZE results in 64 * 1024
turning up in the modinfo output instead of 65536. So use
65536 directly (this was the only way I found of fixing this).
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The maximum possible bandwidth for a speedtouch modem is about 7Mbaud.
You can only get this by using isochronous urbs (enable_isoc=1) and
altsetting 3. With the current default altsetting of 2, the modem
maxes out at about 4Mbaud. So change the default altsetting to 3
when using isochronous urbs. It would be nice to base the altsetting
on the detected line speed, but that's hard given the current design.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A loop on a power-lost resume path used the wrong index.
I suspect khubd has been working around such bugs.
Noticed by Andreas Mohr <andi@rhlx01.fht-esslingen.de>.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A newer board revision changed the type of ethernet phy.
Moreover, this generalizes the way that a phy gets switched
into fiber mode when autodetection is not available.
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
We found a new chip setting that we need in order
to make the driver work more reliable.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Ensure that 8-bit mode is selected for the on-board Realtek RTL8019AS chip
on Toshiba RBHMA4x00, get rid of the duplicate #ifdef's when setting
ei_status.word16.
The chip's datasheet says that the PSTOP register shouldn't exceed 0x60 in
8-bit mode -- ensure this too.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
since the au1000 driver already selects the CRC32 routines, simply replace
the internal ether_crc() implementation with the semantically equivalent
one from <linux/crc32.h>
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The newest Yukon Ultra chipset's require more special tweaks.
They seem to be like the Yukon XL chipsets. This code is transliterated
from the latest SysKonnect driver; I don't have any Ultra hardware.
Signed-off-by: Stephe Hemminger <shemminger@osdl.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
It is more efficient not to write the status ring from the
processor and just read the active portion.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Need to make the edge-triggered workaround timer faster to get marginally
better peformance. The test_and_set_bit in schedule_prep() acts as a barrier
already. Make it a module parameter so that laptops who are concerned
about power can set it to 0; and user's stuck with broken BIOS's
can turn the driver into pure polling.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Gcc isn't smart enough to know that it can do a modulo
operation with power of 2 constant by doing a mask.
So add macro to do it for us.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Mask for transmit ring status was picking up bits from the
unused sync ring. They were always zero, so far...
Also, make sure to remind self not to make tx ring too big.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The status interrupt flag should be cleared before processing,
not afterwards to avoid race. Need to process in poll routine
even if no new interrupt status. This is a normal occurrence when
more than 64 frames (NAPI weight) are processed in one poll routine.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
This is a backout of earlier patch.
The whole rescheduling hack was a bad idea. It doesn't really solve
the problem and it makes the code more complicated for no good reason.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Taking the cpu hotplug semaphore in a normal events workqueue
is unsafe because other tasks can wait for any workqueues with
it hold. This results in a deadlock.
Move the DBS timer into its own work queue which is not
affected by other work queue flushes to avoid this.
Has been acked by Venkatesh.
Cc: venkatesh.pallipadi@intel.com
Cc: cpufreq@lists.linux.org.uk
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use NULL instead of 0 for a null pointer value (sparse warning):
drivers/net/irda/irda-usb.c:1781:30: warning: Using plain integer as NULL pointer
Also, correct timeout argument to use milliseconds instead of jiffies.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the support of attribute groups in class_device's to allow
groups to be created as part of the registration process. This allows
network device's to avoid race between registration and creating
groups.
Note that unlike attributes that are a property of the class object,
the groups are a property of the class_device object. This is done
because there are different types of network devices (wireless for
example).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix:
drivers/rtc/rtc-sa1100.c: In function `sa1100_rtc_proc':
drivers/rtc/rtc-sa1100.c:298: warning: unsigned int format, long unsigned int arg (arg 3)
and arrange for sa1100_rtc_open() to pass the devid to free_irq()
rather than NULL.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Greg Kroah-Hartman