Hi,
This is a patch to incorporate comments from earlier 12 patches.
It also fixes a few issues we found during this time.
Following is a list of changes in this patch. Item 1 incorporates
earlier comments. Issues addressed in items 2 to 4 were discovered
recently.
1. wmb() call in s2io_xmit() replaced with mmiowb().
2. The dtx_control register was earlier programmed incorrectly
for Xframe II adapter.
3. As suggested by hardware team, after a reset, in case of
Xframe II adapter, we clear certain spurious errors by
clearing PCI-X ECC status register, "detected parity error"
bit in PCI_STATUS register and PCI_STATUS bit in txpic_int register.
4. On IBM PPC platforms, we found that in the Rx buffer replenish
function, two memory writes(one to the the descriptor length and
another to the ownership) were getting reordered. This was causing
the adapter to see the ownership transfered to it before the length
was updated.
One solution was to add a wmb() but since this would turnout expensive
on some platforms if called for every descriptor, we set the ownership
bit and other fields of '2' to 'N' Rx descriptors followed by a wmb()
and then set the ownership of first descriptor ('1').
Here the value 'N' is configurable by making it a module loadable
parameter (rxsync_frequency).
(NOTE: This parameter is a power of 2).
5. Bumped up the driver version no. to 2.0.2.1
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
The last patch in this series fixes the following issues found during
testing.
1. Ensure we don't pass zero sized buffers to the card(which can lockup)
2. Restore the PCI-X parameters(in case of Xframe I adapter) after a reset.
3. Make sure total size of all FIFOs does not exceed 8192.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
The below patch implements a new "Link state change handling"
scheme supported by the Xframe II adapter. It also bumps up the
driver version to 2.0.2.0.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This is a patch to provide bimodal interrupt moderation support for
Xframe II adapter. Basically, in this moderation scheme, the adapter
raises a traffic interrupt if the no. of packets transmitted and/or
received reaches a programmable threshold.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch provides basic support for the Xframe II adapter.
Includes the following changes:
1. New values to program XAUI interface.
2. Print the PCI/PCI-X mode(bus frequency, width).
3. Remove EOI from reset during intialization.
4. Enable all 8 PCCs if Xframe II adapter.
5. Programs the RLDRAM size depending on the device.
(Note: RLDRAM size on XFARME-I is 64Mb whereas on XFRAME-II it's 32 Mb).
6. Enable extended(64-bit) statistics counters.
7. Program timer interrupt duration based on PCI/PCI-X clock speed.
8. Not required to save/restore PCI config space before/after reset.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch implements the slow-path handling functions(link
state change, hardware errors) as a timer. It is not
handled in interrupt handler as was done previously.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch relates to mostly performance related changes.
1. Fixed incorrect computation of PANIC level in rx_buffer_level().
2. Removed unnecessary PIOs(read/write of tx_traffic_int and
rx_traffic_int) from interrupt handler and removed read of
general_int_status register from xmit routine.
3. Enable two-buffer mode(for Rx path) automatically for SGI
systems. This improves Rx performance dramatically on
SGI systems.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch fixes certain memory leaks discovered in free_tx_buffers()
and rx_osm_handler()
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
Below patch includes fixes for few purely software bugs identified
since last release.
1. Keep track and display(as part of ethtool command output) the no.
of single-bit and double-bit ECC errors.
2. Handle race condition between intr handler and "interface down"
routine.
3. Initial link state setting modified so that the link state displayed
after "interface Up" is correct.
4. Fix for "Incorrect Tx packet count when TSO is enabled".
5. Disable periodic DMA of statistics and schedule one-shot DMA
only when required.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
Below patch addresses few h/w specific issues.
1. Check for additional ownership bit on Rx path before
starting Rx processing.
2. Enable only 4 PCCs(Per Context Controller) for Xframe I
revisions less than 4.
3. Program Rx and Tx round robin registers depending on
no. of rings/FIFOs.
4. Tx continous interrupts is now a loadable parameter.
5. Reset the card if we get double-bit ECC errors.
6. A soft reset of XGXS being done to force a link state change has been
eliminated.
7. After a reset, clear "parity error detected" bit,
PCI-X ECC status register, and PCI_STATUS bit in
tx_pic_int register.
8. The error in the disabling allmulticast implementation has been
rectified.
9. Leave the PCI-X parameters MMRBC, OST etc. at their
BIOS/system defaults.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
We are submitting a series of 13 patches to support our Xframe I and
Xframe II line of products. The patches can be categorized as follows:
Patches 1-8 : Changes applicable to both Xframe I and II
Patches 9-11: Xframe II specific features
Patch 12: Addresses issues found during testing cycle.
Patch 13: Incorpoates mostly the review comments from community
and some last moment bug fixes.
Please review the patches and let us know your comments.
Starting with patch 1 below.
This patch involves cosmetic changes(tabs and indentation,
regrouping of transmit and receive data structures, typecasting,
code cleanup).
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Well I've only found one potential cause for the assertion
failure in tcp_mark_head_lost. First of all, this can only
occur if cnt > 1 since tp->packets_out is never zero here.
If it did hit zero we'd have much bigger problems.
So cnt is equal to fackets_out - reordering. Normally
fackets_out is less than packets_out. The only reason
I've found that might cause fackets_out to exceed packets_out
is if tcp_fragment is called from tcp_retransmit_skb with a
TSO skb and the current MSS is greater than the MSS stored
in the TSO skb. This might occur as the result of an expiring
dst entry.
In that case, packets_out may decrease (line 1380-1381 in
tcp_output.c). However, fackets_out is unchanged which means
that it may in fact exceed packets_out.
Previously tcp_retrans_try_collapse was the only place where
packets_out can go down and it takes care of this by decrementing
fackets_out.
So we should make sure that fackets_out is reduced by an appropriate
amount here as well.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PFM_LOAD_CONTEXT may fail silently and cause a session
to remain reserved even though it should not. This can happen
when the commands succeeds in reserving the session but fails
when it actually tries to attach to the load_pid. In that case,
the command has failed but will return 0. More importantly,
the session will remain reserved. This patch fixes the problem.
Signed-off-by: <stephane.eranian@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes the following stupid compile error that happens
when CONFIG_HOTPLUG is not defined on ia64.
arch/ia64/kernel/built-in.o(.text+0x712): In function `acpi_unregister_ioapic':
: undefined reference to `iosapic_remove'
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
We have a chek in there to make sure that the name won't overflow
task_struct.comm[], but it's triggering for scsi with lots of HBAs, only
scsi is using single-threaded workqueues which don't append the "/%d"
anyway.
All too hard. Just kill the BUG_ON.
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
[ kthread_create() uses vsnprintf() and limits the thing, so no
actual overflow can actually happen regardless ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Even though the changes are minor for the next release an increasing
version number simplifies my support issues.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The workaround for broken device-tree that prevents fan control from
working on recent G5 models need to be "enabled" for machines with
revision 0x37 of the bridge in addition to machines with revision 0x35.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Need to use list_for_entry_safe(), as we're removing items during the
traversal. list_for_each_entry() uses the first ptr also as an iterator, if
you kfree() it slab takes it, might poison it and then you try to use it to
iterate to the next object in list.
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the p-persistence CSMA algorithm which in simplex mode was starting
with a slottime delay before doing anything else as if there was carrier
collision resulting in bad performance on simplex links.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hello,
This patch adds the Intel ICH7-M DH DID to the ahci.c file for AHCI mode SATA support. This patch was built against the 2.6.13-rc6 kernel.
If acceptable, please apply.
Thanks,
Jason Gaston
Signed-off-by: Jason Gaston <Jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
sata_sx4 directly references sg->length to calculate total_len in
pdc20621_dma_prep(). This is incorrect as dma_map_sg() could have
merged multiple sg's into one and, in such case, sg->length doesn't
reflect true size of the entry. This patch makes it use
sg_dma_len(sg).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
TxAnchor.anon_list is protected by jfsTxnLock (TXN_LOCK), but there was
a place in txLock() that was removing an entry from the list without holding
the spinlock.
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Patch from Ben Dooks
Rename the s3c2410_report_oc() to s3c2410_usb_report_oc()
as this is an usb specific function.
Change port power on the usb-simtec implementation to only
power up the output if both are set, as per the usb 1.1
specification
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Documentation for the in-built OHCI host controller
and the support for it in Linux.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, we can't use the "user" bit in the page tables to
control whether a page table entry is "global" or "asid" specific,
since the vector page is mapped as "user" accessible but is not
process specific.
Therefore, give direct control of the ARMv6 "nG" (not global)
bit to the mm layers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. Move hwif_to_node to ide.h
2. Use hwif_to_node in ide-disk.c
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the tda9887 stuff from lgdt330x.c. It's experimental code
which wasn't supposed to leak out and we don't want it in 2.6.13.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Acked-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Two trivial text changes in Kconfig and lgdt330x.c
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added pci_request_regions() before using the controller to avoid duplicate
usage of the I2O controller when the dpt_i2o driver and I2O subsystem is
loaded at the same time.
Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tony Luck