When jprobe is hit, the function parameters of the original function
should be saved before jprobe handler is executed, and restored it after
jprobe handler is executed, because jprobe handler might change the
register values due to tail call optimization by the gcc.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The default of using jiffies is very bad and results in
underutilization except with very low bandwidth.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the source address of a tunnel is given as 0.0.0.0 do a routing lookup
to get the real source address for the destination and fill that into the
acquire message. This allows to specify policies like this:
spdadd 172.16.128.13/32 172.16.0.0/20 any -P out ipsec
esp/tunnel/0.0.0.0-x.x.x.x/require;
spdadd 172.16.0.0/20 172.16.128.13/32 any -P in ipsec
esp/tunnel/x.x.x.x-0.0.0.0/require;
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes redundant comments, and moves one comment to a better
location.
Signed-off-by: Kris Katterjohn <kjak@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are errors and inconsistency in the display of NIP6 strings.
ie: net/ipv6/ip6_flowlabel.c
There are errors and inconsistency in the display of NIPQUAD strings too.
ie: net/netfilter/nf_conntrack_ftp.c
This patch:
adds NIP6_FMT to kernel.h
changes all code to use NIP6_FMT
fixes net/ipv6/ip6_flowlabel.c
adds NIPQUAD_FMT to kernel.h
fixes net/netfilter/nf_conntrack_ftp.c
changes a few uses of "%u.%u.%u.%u" to NIPQUAD_FMT for symmetry to NIP6_FMT
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hotplug cpu support to salinfo.c.
The cpu_event field is a cpumask so use the cpu_* macros consistently,
replacing the existing mixture of cpu_* and *_bit macros.
Instead of counting the number of outstanding events in a semaphore and
trying to track that count over user space context, interrupt context,
non-maskable interrupt context and cpu hotplug, replace the semaphore
with a test for "any bits set" combined with a mutex.
Modify the locking to make the test for "work to do" an atomic
operation.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
We need to handle debug traps in fsys mode non-fatally. They can
happen now that we have fsyscalls which contain probe instructions.
Signed-off-by: Jason Uhlenkott <jasonuhl@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch separates the sn_flush_device_list struct into kernel and
common (both kernel and PROM accessible) structures. As it was, if the
size of a spinlock_t changed (due to additional CONFIG options, etc.) the
sal call which populated the sn_flush_device_list structs would erroneously
write data (and cause memory corruption and/or a panic).
This patch does the following:
1. Removes sn_flush_device_list and adds sn_flush_device_common and
sn_flush_device_kernel.
2. Adds a new SAL call to populate a sn_flush_device_common struct per
device, not per widget as previously done.
3. Correctly initializes each device's sn_flush_device_kernel spinlock_t
struct (before it was only doing each widget's first device).
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
I originally thought this was an bug only in the SN code, but I think I
also see a hole in the generic IA64 tlb code. (Separate patch was sent
for the SN problem).
It looks like there is a bug in the TLB flushing code. During context switch,
kernel threads (kswapd, for example) inherit the mm of the task that was
previously running on the cpu. Normally, this is ok because the previous context
is still loaded into the RR registers. However, if the owner of the mm
migrates to another cpu, changes it's context number, and references a
page before kswapd issues a tlb_purge for that same page, the purge will be
done with a stale context number (& RR registers).
Signed-off-by: Tony Luck <tony.luck@intel.com>
Altix (shub2) pushes the BTE clean-up into SAL.
This patch correctly interfaces with the now implemented SAL call.
It also fixes a bug when delaying clean-up to allow busy BTEs to
complete (or error out).
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
On return from INIT handler we must convert the address of the
minstate area from a kernel virtual uncached address (0xC...)
to physical uncached (0x8...). A typo (or thinko?) in the code
converted to physical cached.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Increasing the module ref count at registration will block the module from
ever being unloaded. In fact, genetlink should not care about the owner at
all. This patch removes the owner field from the struct registered with
genetlink.
Signed-off-by: Per Liden <per.liden@ericsson.com>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes device_shutdown() to use the newly introduced safe
reverse list traversal. We experienced loops on system reboot if we had
removed and re-inserted our device from the device list.
We noticed this problem on PPC405. Our PCI IDE device comes and goes a lot.
Our hypothesis was that there was a loop caused by the driver->shutdown
freeing memory. It is possible that we do something wrong as well, but
being unable to reboot is kind of nasty.
Signed-off-by: Michael Richardson <mcr@marajade.sandelman.ca>
Cc: Patrick Mochel <mochel@digitalimplant.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Please fold this typo fix into platform-device-del.patch, as was
discussed earlier on LKML:
http://lkml.org/lkml/2005/12/10/76
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch converts css_bus_type and ccw_bus_type to use
the new bus_type methods.
Signed-off-by: Cornelia Huck <huckc@de.ibm.com>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB gadget drivers make no use of these, remove the pointless
comments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the PCI bus device probe/remove methods to the bus_type
structure. We leave the shutdown method alone since there
are compatibility issues with that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add bus_type probe, remove and shutdown methods to replace the
corresponding methods in struct device_driver. This matches
the way we handle the suspend/resume methods.
Since the bus methods override the device_driver methods, warn
if a device driver is registered whose methods will not be
called.
The long-term idea is to remove the device_driver methods entirely.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cleanup a few items after moving xpc.h from arch/ia64/sn/kernel to
include/asm-ia64/sn.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Move xpc.h from arch/ia64/sn/kernel to include/asm-ia64/sn without change.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Move xpc_system_reboot() to be closer to the file it calls for readability
reasons (which are indeed subjective).
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Zhang Yanmin