The nommu code has regressed somewhat in that 29BIT gets set for the
SH-2/2A configs regardless of the fact that they are really 32BIT sans
MMU or PMB. This does a bit of tidying to get nommu properly selecting
32BIT as it was before.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This sets up a generic SRAM pool for CPUs and platform code to insert
their otherwise unused memories into. A simple alloc/free interface is
provided (lifed from avr32) for generic code.
This only applies to tiny SRAMs that are otherwise unmanaged, and does
not take in to account the more complex SRAMs sitting behind transfer
engines, or that employ an I/D split.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements a bit of rework for the PMB code, which permits us to
kill off the legacy PMB mode completely. Rather than trusting the boot
loader to do the right thing, we do a quick verification of the PMB
contents to determine whether to have the kernel setup the initial
mappings or whether it needs to mangle them later on instead.
If we're booting from legacy mappings, the kernel will now take control
of them and make them match the kernel's initial mapping configuration.
This is accomplished by breaking the initialization phase out in to
multiple steps: synchronization, merging, and resizing. With the recent
rework, the synchronization code establishes page links for compound
mappings already, so we build on top of this for promoting mappings and
reclaiming unused slots.
At the same time, the changes introduced for the uncached helpers also
permit us to dynamically resize the uncached mapping without any
particular headaches. The smallest page size is more than sufficient for
mapping all of kernel text, and as we're careful not to jump to any far
off locations in the setup code the mapping can safely be resized
regardless of whether we are executing from it or not.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This splits out the uncached mapping support under its own config option,
presently only used by 29-bit mode and 32-bit + PMB. This will make it
possible to optionally add an uncached mapping on sh64 as well as booting
without an uncached mapping for 32-bit.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some devices need to be ioremap'd and accessed very early in the boot
process. It is not possible to use the standard ioremap() function in
this case because that requires kmalloc()'ing some virtual address space
and kmalloc() may not be available so early in boot.
This patch provides fixmap mappings that allow physical address ranges
to be remapped into the kernel address space during the early boot
stages.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
All SH-X2 and SH-X3 parts support an extended TLB mode, which has been
left as experimental since support was originally merged. Now that it's
had some time to stabilize and get some exposure to various platforms,
we can drop it as an option and default enable it across the board.
This is also good future proofing for newer parts that will drop support
for the legacy TLB mode completely.
This will also force 3-level page tables for all newer parts, which is
necessary both for the varying page sizes and larger memories.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This introduces some much overdue chainsawing of the fixed PMB support.
fixed PMB was introduced initially to work around the fact that dynamic
PMB mode was relatively broken, though they were never intended to
converge. The main areas where there are differences are whether the
system is booted in 29-bit mode or 32-bit mode, and whether legacy
mappings are to be preserved. Any system booting in true 32-bit mode will
not care about legacy mappings, so these are roughly decoupled.
Regardless of the entry point, PMB and 32BIT are directly related as far
as the kernel is concerned, so we also switch back to having one select
the other.
With legacy mappings iterated through and applied in the initialization
path it's now possible to finally merge the two implementations and
permit dynamic remapping overtop of remaining entries regardless of
whether boot mappings are crafted by hand or inherited from the boot
loader.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This has the adverse effect of converting many 29bit configs to 32bit
mode, while this is a change that needs to be done manually for each
platform. Turn it off by default in order to cut down on spurious bug
reports.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
While the PMB is available on SH-4A parts, SH4AL-DSP parts exclude it
altogether. As such, explicitly disable PMB support for these parts. If
this changes in the future for newer subtypes, this will have to be made
more fine-grained.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The previous expressions were wrong which made free_pmd_range() explode
when using anything other than 4KB pages (which is why 8KB and 64KB
pages were disabled with the 3-level page table layout).
The problem was that pmd_offset() was returning an index of non-zero
when it should have been returning 0. This non-zero offset was used to
calculate the address of the pmd table to free in free_pmd_range(),
which ended up trying to free an object that was not aligned on a page
boundary.
Now 3-level page tables should work with 4KB, 8KB and 64KB pages.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
If using 64-bit PTEs and 4K pages then each page table has 512 entries
(as opposed to 1024 entries with 32-bit PTEs). Unlike MIPS, SH follows
the convention that all structures in the page table (pgd_t, pmd_t,
pgprot_t, etc) must be the same size. Therefore, 64-bit PTEs require
64-bit PGD entries, etc. Using 2-levels of page tables and 64-bit PTEs
it is only possible to map 1GB of virtual address space.
In order to map all 4GB of virtual address space we need to adopt a
3-level page table layout. This actually works out better for
CONFIG_SUPERH32 because we only waste 2 PGD entries on the P1 and P2
areas (which are untranslated) instead of 256.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the PMB options were limited to a number of CPUs they were
tested with, but it is generally available on all SH-4A CPUs, so just
drop the subtype conditionals.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The hugetlb dependencies presently depend on SUPERH && MMU while the
hugetlb page size definitions depend on CPU_SH4 or CPU_SH5. This
unfortunately allows SH-3 + MMU configurations to enable hugetlbfs
without a corresponding HPAGE_SHIFT definition, resulting in the build
blowing up.
As SH-3 doesn't support variable page sizes, we tighten up the
dependenies a bit to prevent hugetlbfs from being enabled. These days
we also have a shiny new SYS_SUPPORTS_HUGETLBFS, so switch to using
that rather than adding to the list of corner cases in fs/Kconfig.
Reported-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This enables SCHED_MC support for SH-X3 multi-cores. Presently this is
just a simple wrapper around the possible map, but this allows for
tying in support for some of the more exotic NUMA clusters where we can
actually do something with the topology.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CONFIG_PMB will eventually allow the MMU to be switched between 29-bit
and 32-bit mode dynamically at runtime.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Several platforms want to be able to do large physically contiguous
allocations (primarily nommu and video codecs on SH-Mobile), provide a
MAX_ORDER override for those cases.
Tested-by: Conrad Parker <conrad@metadecks.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Consolidate these in a single place in the Kconfig menus. At the same
time, disable their interactivity and set them according to the board
config defaults.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Forcing direct-mapped worked on certain older 2-way set associative
parts, but was always error prone on 4-way parts. As these are the
norm these days, there is not much point in continuing to support this
mode. Most of the folks that used direct-mapped mode generally just
wanted writethrough caching in the first place..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a method for supporting fixed PMB mappings inherited from
the bootloader, as an alternative to the dynamic PMB mapping currently
used by the kernel. In the future these methods will be combined.
P1/P2 area is handled like a regular 29-bit physical address, and local
bus device are assigned P3 area addresses.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently we oops in mm/hugetlb.c:1325, which is the order == 0 test in
hugetlb_add_hstate() called at initialization time. So, disable 64kB
huge pages when we're using a 64kB PAGE_SIZE. On most parts this will
force the default to be 1MB huge pages.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
fix the problem that cannot boot using uImage when PAGE_SIZE is
8kbyte or 64kbyte.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
16kB is a useful size on nommu, while 64kB still tends to be too big to
be useful. Newer MMUs are likely to support this as well, so plug it
in in anticipation of those, too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
PAGE_SIZE doesn't need to be fixed at 4096 on nommu, so stub in a !MMU
case for the various PAGE_SIZE Kconfig options.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There's still work that needs to be done here, and this should not be
enabled by default on existing boards.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The ST40 stuff in-tree hasn't built for some time, and hasn't been
updated for over 3 years. ST maintains their own out-of-tree changes
and rebases occasionally, and that's ultimately where all of the ST40
users go anyways.
In order for the ST40 code to be brought up to date most of the stuff
removed in this changeset would have to be rewritten anyways, so there's
very little benefit in keeping the remnants around either.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When using URAM in NUMA mode another active region is needed.
Bump this up so we don't trigger the region truncation in
add_active_range().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
4kB pages are unstable on extended mode TLB, it's recommended
that TLB compat mode be used when using a 4kB PAGE_SIZE. Set
the default for extended mode to 8kB.
This should have negligible impact, as other than the extra swap
cache entry bits, there's no reason to use the extended mode TLB
with 4kB pages.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds basic support for SH-X3 SMP (4 CPUs).
More IPI and cache debugging is necessary, mostly interfacing the
d-cache coherency and the I-cache broadcast invalidates. Only for
testing at present!
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This leads to invalid configurations where both FPU and DSP support
can be enabled in the same kernel, resulting in build failure.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains the following fixes:
- Adds sh7785 support to CONFIG_EARLY_SCIF_CONSOLE_PORT.
- Removes duplicate include from rts7751r2d irq code.
- Removes CONFIG_CPU_HAS_INTC from sh7720 Kconfig entry.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All processor specific interrupt code is now converted to make use
of the new intc code. The config option CONFIG_CPU_HAS_INTC_IRQ is
because of that pointless.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the cpu specific interrupt setup code for sh7206
from ipr to intc. New vectors are also added to match the information
provided by the datasheet.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the cpu specific interrupt setup code for sh7619
from ipr to intc. New vectors are also added to match the information
provided by the datasheet.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the SH7720 (SH3-DSP) CPU.
Signed-off by: Markus Brunner <super.firetwister@gmail.com>
Signed-off by: Mark Jonas <toertel@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There is no point in keeping around the now unused intc2 code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the cpu specific interrupt setup code for x3 from
intc2 to intc. New vectors are also added to match the preliminary
information.
Use plat_irq_setup_pins() to select between IRQ and IRL mode for IRQ0-3.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt