This patch hacks the current PowerMac Alsa driver to add some basic support
of analog sound output to some desktop G5s. It has severe limitations
though:
- Only 44100Khz 16 bits
- Only work on G5 models using a TAS3004 analog code, that is early
single CPU desktops and all dual CPU desktops at this date, but none
of the more recent ones like iMac G5.
- It does analog only, no digital/SPDIF support at all, no native
AC3 support
Better support would require a complete rewrite of the driver (which I am
working on, but don't hold your breath), to properly support the diversity
of apple sound HW setup, including dual codecs, several i2s busses, all the
new codecs used in the new machines, proper clock switching with digital,
etc etc etc...
This patch applies on top of the other PowerMac sound patches I posted in
the past couple of days (new powerbook support and sleep fixes).
Note: This is a FAQ entry for PowerMac sound support with TI codecs: They
have a feature called "DRC" which is automatically enabled for the internal
speaker (at least when auto mute control is enabled) which will cause your
sound to fade out to nothing after half a second of playback if you don't
set a proper "DRC Range" in the mixer. So if you have a problem like that,
check alsamixer and raise your DRC Range to something reasonable.
Note2: This patch will also add auto-mute of the speaker when line-out jack
is used on some earlier desktop G4s (and on the G5) in addition to the
headphone jack. If that behaviour isn't what you want, just disable
auto-muting and use the manual mute controls in alsamixer.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch improves the behaviour of the "tumbler/snapper" driver used on
newer PowerMacs during sleep. It properly set the HW mutes to shut down
amplifiers and does an analog shutdown of the codec. That might improve
power consumption during sleep on a number of machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch hacks the current Alsa snd-powermac driver to add support for
recent machine models with the tas3004 chip, that is basically new laptop
models. The Mac Mini is _NOT_ yet supported by this patch (soon soon ...).
The G5s (iMac or Desktop) will need the rewritten sound driver on which
I'm working on (I _might_ get a hack for analog only on some G5s on the
current driver, but no promise).
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch allows Kconfig to build the MV643xx ethernet driver on Pegasos
(CONFIG_PPC_MULTIPLATFORM) and adds what I think is a missing fix from
Dale's batch, that is remove SA_INTERRUPT and add SA_SHIRQ in there as the
interrupt is shared if I understand things correctly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Fabio Massimo Di Nitto <fabbione@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
make defconfig give the following error on ppc (gcc-4):
arch/ppc/syslib/open_pic.c:36: error: static declaration of ‘OpenPIC’ follows non-static declaration
arch/ppc/syslib/open_pic_defs.h:175: error: previous declaration of ‘OpenPIC’ was here
Signed-Off-By: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
make defconfig give the following error on ppc (gcc-4):
arch/ppc/syslib/prom_init.c:120: error: static declaration of ‘prom_display_paths’ follows non-static declaration
include/asm/prom.h:17: error: previous declaration of ‘prom_display_paths’ was here
arch/ppc/syslib/prom_init.c:122: error: static declaration of ‘prom_num_displays’ follows non-static declaration
include/asm/prom.h:18: error: previous declaration of ‘prom_num_displays’ was here
Signed-Off-By: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
make defconfig give the following error on ppc (gcc-4):
arch/ppc/kernel/time.c:92: error: static declaration of ‘time_offset’
follows non-static declaration
include/linux/timex.h:236: error: previous declaration of ‘time_offset’
was here
The following patch solves it (time_offset is declared in timer.c).
Signed-Off-By: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
make defconfig give the following error on ppc (gcc-4):
include/asm-m68k/setup.h:365: error: array type has incomplete element
type
Signed-Off-By: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch restores the original behaviour of prep_pcibios_fixup() to only
call prep_pib_init() on machines with an openpic. This allows the
Powerstack II Pro4000 to boot again.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When building a ppc32 MULTIPLATFORM kernel for a 64bit pmac, we try and
build certain files or use certain functions that make no sense in that
context. This catches the last of these.
Signed-off-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following problem was found by Giovambattista Pulcini
<gpulcini@swintel.it>, who also provided a partial patch, and this has been
verified by our time guru Gabriel Paubert <paubert@iram.es>.
The problem is that in do_settimeofday() we always set time_state to
TIME_ERROR and except on two platforms, never re-set it. This meant that
ntp_gettime() and ntp_adjtime() always returned TIME_ERROR, incorrectly.
Based on Gabriel's analysis, time_state is used for leap-second processing,
and ppc shouldn't be mucking with it.
Signed-off-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The CONFIG_8xx_WDT option got broken in the generic hardirq update as ppc32
had its own different request_irq that worked when other arches used
setup_irq. This is the trivial fix for the problem.
From: Carsten Juttner <carjay@gmx.net>
Signed-off-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To add support for 36-bit physical addressing on e500 the following changes
have been made. The changes are generalized to support any physical address
size larger than 32-bits:
* Allow FSL Book-E parts to use a 64-bit PTE, it is 44-bits of pfn, 20-bits
of flags.
* Introduced new CPU feature (CPU_FTR_BIG_PHYS) to allow runtime handling of
updating hardware register (SPRN_MAS7) which holds the upper 32-bits of
physical address that will be written into the TLB. This is useful since
not all e500 cores support 36-bit physical addressing.
* Currently have a pass through implementation of fixup_bigphys_addr
* Moved _PAGE_DIRTY in the 64-bit PTE case to free room for three additional
storage attributes that may exist in future FSL Book-E cores and updated
fault handler to copy these bits into the hardware TLBs.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow the pfn to be offset by more than just PAGE_SHIFT in the pte. Today,
PAGE_SHIFT tends to allow us to have 12-bits of flags in the pte. In the
future if we have a larger pte we can allocate more bits for flags by
offsetting the pfn even further.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_PTE_64BIT & CONFIG_PHYS_64BIT are not currently consistently used in
the code base. Fixed up the usage such that CONFIG_PTE_64BIT is used when we
have a 64-bit PTE regardless of physical address width. CONFIG_PHYS_64BIT is
used if the physical address width is larger than 32-bits, regardless of PTE
size.
These changes required a few sub-arch specific ifdef's to be fixed and the
introduction of a physical address format string.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While the existing pte_update code handled atomically modifying a 64-bit PTE,
it did not return all 64-bits of the PTE before it was modified. This causes
problems in some places that expect the full PTE to be returned, like
ptep_get_and_clear().
Created a new pte_update function that is conditional on CONFIG_PTE_64BIT. It
atomically reads the low PTE word which all PTE flags are required to be in
and returns a premodified full 64-bit PTE.
Since we now have an explicit 64-bit PTE version of pte_update we can also
remove the hack that existed to get the low PTE word regardless of size.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
My previous patch that added sleep support for uninorth-agp and some AGP
"off" stuff in radeonfb and aty128fb is breaking some configs. More
specifically, it has problems with rage128 setups since the DRI code for
these in X doesn't properly re-enable AGP on wakeup or console switch
(unlike the radeon DRM).
This patch fixes the problem for pmac once for all by using a different
approach. The AGP driver "registers" special suspend/resume callbacks with
some arch code that the fbdev's can later on call to suspend and resume
AGP, making sure it's resumed back in the same state it was when suspended.
This is platform specific for now. It would be too complicated to try to
do a generic implementation of this at this point due to all sort of weird
things going on with AGP on other architectures. We'll re-work that whole
problem cleanly once we finally merge fbdev's and DRI.
In the meantime, please apply this patch which brings back some r128 based
laptops into working condition as far as system sleep is concerned.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch updates the PowerMac cpufreq driver. It depends on the addition
of the suspend() method (my previous patch) and on the new flag I defined
to silence some warnings that are normal for us.
It fixes various issues related to cpufreq on pmac, including some crashes
on some models when sleeping the machine while in low speed, proper voltage
control on some newer machines, and adds voltage control on 750FX based G3
laptops.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On ppc, we emulate instructions that cause alignment exceptions. If we are
single-stepping an instruction and it causes an alignment exception, we
will currently do the next instruction as well before taking the
single-step exception. This patch fixes that, so we take the single-step
exception after emulating the instruction.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we should happen to get an altivec assist exception while executing in
the kernel, we will currently try to handle it and fail, and end up oopsing
with (apparently) a segfault. (An altivec assist exception occurs for
floating-point altivec instructions with denormalized inputs or outputs if
the altivec unit is in java mode.)
This patch checks explicitly if we are in user mode and prints a useful
message if not.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently the procedure in the ppc32 kernel that synchronizes the timebase
registers across an SMP powermac system does so by setting both timebases
to zero. That is OK at boot but causes problems if done later. So that we
can do hotplug CPU on these machines, this patch changes the code so it
reads the timebase from one CPU and transfers the value to the other CPU.
(Hotplug CPU is needed for sleep (aka suspend to RAM) to work.)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds interrupt acknowledge to the PPC4xx PIC enable_irq
implementation for level-sensitive IRQ sources. This helps in cases when
enable/disable_irq is used in interrupt handlers for hardware, which
requires IRQ acknowledge to be issued from non-interrupt context (e.g.
when actual ACK in device needs an I2C transaction). For such strange
hardware, interrupt handler disables IRQ and defers actual ACK to some
other context. When this happens, IRQ is enabled again. For
level-sensitive sources we get spurious triggering right after IRQ is
enabled. This patch fixes this.
Suggested by Tolunay Orkun <listmember@orkun.us>.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code that went into arch/ppc/kernel/signal.c recently to handle process
freezing seems to contain a dubious assumption: that a process that calls
do_signal when PF_FREEZE is set will have entered the kernel because of a
system call. This patch removes that assumption.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds SELinux support for the KOBJECT_UEVENT Netlink family, so
that SELinux can apply finer grained controls to it. For example, security
policy for hald can be locked down to the KOBJECT_UEVENT Netlink family
only. Currently, this family simply defaults to the default Netlink socket
class.
Note that some new permission definitions are added to sync with changes in
the core userspace policy package, which auto-generates header files.
Signed-off-by: James Morris <jmorris@redhat.com>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we are not the real parent of the dst (e.g., when we're xfrm_dst and
the child is an rtentry), it may already be on the GC list.
In fact the current code is buggy to, we need to check dst->flags before
the dec as dst may no longer be valid afterwards.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes the warning reported by Marcel Holtmann (Thanks!).
Signed-off-by: Arnaldo Carvalho de Melo <acme@conectiva.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This recently got changed to include a lot of kernel internal stuff in the
non-__KERNEL__ area of the header, which isn't so kosher and breaks libc
builds.
The fix is pretty simple.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Working on some code lately I've been getting huge values for "Cached".
The cause is that get_page_cache_size() is an approximate value, and for a
sufficiently small returned value of get_page_cache_size() the value
underflows.
Signed-off-by: Martin Hicks <mort@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
We only call pageout() for dirty pages, so this test is redundant.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
iscsi/lvm2/multipath needs guaranteed protection from the oom-killer, so
make the magical value of -17 in /proc/<pid>/oom_adj defeat the oom-killer
altogether.
(akpm: we still need to document oom_adj and friends in
Documentation/filesystems/proc.txt!)
Signed-off-by: Andrea Arcangeli <andrea@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We will return NULL from filemap_getpage when a page does not exist in the
page cache and MAP_NONBLOCK is specified, here:
page = find_get_page(mapping, pgoff);
if (!page) {
if (nonblock)
return NULL;
goto no_cached_page;
}
But we forget to do so when the page in the cache is not uptodate. The
following could result in a blocking call:
/*
* Ok, found a page in the page cache, now we need to check
* that it's up-to-date.
*/
if (!PageUptodate(page))
goto page_not_uptodate;
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drm: fix r128_state.c switch statements.. in drivers/char/drm/r128_state.c
(linux-2.6.12-rc2), some breaks are missing in the switch statement. See
trivial fix below.
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a bug in the SELinux Netlink message type detection code,
where the wrong constant was being used in a case statement. The incorrect
value is not valid for this class of object so it would not have been
reached, and fallen through to a default handler for all Netlink messages.
Signed-off-by: James Morris <jmorris@redhat.com>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Johannes Stezenbach <js@linuxtv.org>
Fix http://bugme.osdl.org/show_bug.cgi?id=4395.
Patch by Manu Abraham and Gerd Knorr:
Remove redundant bttv_reset_audio() which caused the computer to freeze
with some bt8xx based DVB cards when loading the bttv driver.
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I have no idea how a bug like this lasted so long. Anyways, obvious
memset()'ing of incorrect pointer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the access-above-bottom-of-stack crash.
1. Allows to preserve the valueable optimization
2. Works for NMIs
3. Doesn't care whether or not there are more of the like instances
where the stack is left empty.
4. Seems to work for me without the crashes:)
(akpm: this is still under discussion, although I _think_ it's OK. You might
want to hold off)
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Andreas Gruenbacher <agruen@suse.de>
ext[23]_get_acl will return an error when reading the attribute fails or
out-of-memory occurs. Catch this case.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This was unexported by Arjan because we have no current users.
However, during a conversion from tasklets to workqueues of the parisc led
functions, we ran across a case where this was needed. In particular, the
open coded equivalent of cancel_rearming_delayed_workqueue was implemented
incorrectly, which is, I think, all the evidence necessary that this is a
useful API.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the deflate_[compress|uncompress|pcompress] functions we call the
zlib_[in|de]flateReset function at the beginning. This is OK. But when we
unload the deflate module we don't call zlib_[in|de]flateEnd to free all
the zlib internal data. It looks like a bug for me. Please, consider the
attached patch.
Signed-off-by: Artem B. Bityuckiy <dedekind@infradead.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Russell King <rmk+lkml@arm.linux.org.uk>
Oddly, max_low_pfn/max_pfn end up being the number of pages in the system,
rather than the maximum PFN on ARM. This doesn't seem to cause any problems,
so just add a note about it.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Russell King <rmk+lkml@arm.linux.org.uk>
The ARM dma_supported() is rather basic, and I don't think it takes into
account everything that it should do (eg, whether the mask agrees with what
we'd return for GFP_DMA allocations). Note this.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Russell King <rmk+lkml@arm.linux.org.uk>
For some reason, this help text was missed when the file was last audited
by the documentation referencing folk. Fix this incorrect documentation
reference.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Russell King <rmk+lkml@arm.linux.org.uk>
ARM wasn't raising a SIGBUS with a siginfo structure. Fix
__do_user_fault() to allow us to use it for SIGBUS conditions, and arrange
for the sigbus path to use this.
We need to prevent the siginfo code being called if we do not have a user
space context to call it, so consolidate the "user_mode()" tests.
Thanks to Ian Campbell who spotted this oversight.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
..as sync_page_io can be called on the write-out path.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Benjamin Herrenschmidt