Replace all casts from "struct uart_port *" to "struct dz_port *" with a
construct based on container_of(). This makes the conversion work
irrespective of where the former struct is located within the latter.
By popular request I have implemented it as an inline function rather than
a macro this time.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A set of changes to the way termios settings are propagated to the serial
port hardware. The DZ11 only supports a selection of fixed baud settings,
so some requests may not be fulfilled. Keep the old setting in such a case
and failing that resort to 9600bps. Also add a missing update of the
transmit timeout. And remove the explicit encoding of the line selected
from writes to the Line Parameters Register as it has been preencoded by
the ->set_termios() call already. Finally, remove a duplicate macro for
the Receiver Enable bit.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Handle the read and ignore status masks correctly. Handle the BREAK condition
as expected: a framing error with a null character is a BREAK, any other
framing error is a framing error indeed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ->start_tx(), ->stop_tx() and ->stop_rx() backends are called with the
port's lock already taken. Remove locking from within them and wrap around
calls as necessary.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename the serial console structure so that `modpost' does not complain about
a reference to an "init" section -- "_console" is magic.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reformat the Kconfig entries and update descriptions for accuracy. Select the
driver by default for configurations of interest. For the curious: 32BIT
means only 32-bit DECstations support the device, not that the driver is not
64-bit clean; I have not checked that either though.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sort the header inclusions, add a few that are needed but pulled indirectly
only and remove ones that are not really used.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Well, panic() is a little bit undue if request_irq() fails; there is probably
no need to justify it any further. Handle the case gracefully, by
unregistering the driver.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Polled transmission is tricky enough with the DZ11 design. While "loop" is
set to a high value, conceptually you are not allowed to transmit without
checking whether the device offers the right transmission line (yes, it is the
device that selects the line -- the driver has no control over it other than
disabling the transmitter offered if it is the wrong one), so the loop has to
be run at least once.
Well, the '1977 or PDP11 view of how serial lines should be handled... Except
that the serial interface used to be quite an impressive board back then
rather than chip.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unused module function prototypes that would not even build if enabled.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When rebasing one of the mpc5200 psc UART patches I made a mistake and
damaged the patch.
This patch fixes the compile failure introduced in commit
25ae3a0739
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add 512x support using the psc_ops framework established
with the previous patch.
All 512x PSCs share the same interrupt so add
IRQF_SHARED to irq flags.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
PSC devices are different between the mpc5200 and the mpc5121
this patch localizes the differences in preparation for adding mpc5121
support to the psc uart driver.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
New serial driver for SC2681/SC2691 uarts. Older SNI RM400 machines are
using these chips for onboard serial ports.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Torben Mathiasen <device@lanana.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use SGI_HAS_ZILOG for IP22_ZILOG depends
- remove IP22 from description, because the driver works on more than
IP22 SGI machines
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Probing of the console at console_initcall time is broken. It tries to
call memory allocation routines which aren't initialized yet.
Problem solved by removing the early probe entirely. The console init
is called again anyway after the uartlite device is initialized and the
memory allocation routines can be called safely.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Mainly, this involves two changes:
1) xilinx->xlnx (recognized standard is to use the stock ticker)
2) In order to have the device tree focus on describing what the
hardware is as exactly as possible, the compatible strings contain the
full IP name and IP version.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix compile errors in the xilinxfb, xsysace and uartlite drivers used
by the Xilinx Virtex platform
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Use ARRAY_SIZE macroto get maximum ports in ColdFire serial driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The clock to generate the desired baudrate with the MPSC is first divided
by the Baud Rate Generator (BRG) and then by the MPSC itself. So, when the
BRG divider is changed, the MPSC divider must also be changed to generate
the correct baudrate. During MPSC initialization, the BRG divider is
changed but the MPSC divider isn't changed until much later. This results
in some printk's coming out garbled. To fix that, set the MPSC divider at
the same time that the BRG divider is changed.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Invalid speeds are forced to 9600. Update the code for this to encode new
style baud rates properly.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some ports seem to be unable to drain their transmitters on shut down. Such a
problem can occur if the port is programmed for hardware imposed flow control,
characters are in the FIFO but the CTS signal is inactive.
Normally, this isn't a problem because most places where we wait for the
transmitter to drain have a time-out. However, there is no timeout in the
suspend path.
Give a port 30ms to drain; this is an arbitary value chosen to avoid long
delays if there are many such ports in the system, while giving a reasonable
chance for a single port to drain. Should a port not drain within this
timeout, issue a warning.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we boot, serial ports remain in low power mode until they're used either
by userspace or for the kernel console.
However, if you suspend the system, and then resume, all serial ports will be
taken out of low power mode. This is bad news for embedded devices where this
can mean higher power consumption.
Only bring a serial port out of low power mode if the port is being used as
the kernel console, or is in use by userspace.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow the private_data field to be specified in platform_data for the
standard 8250/16550 UART. This field is used by DW APB type UARTs and
without this patch it's only possible to set this field when registering
the port by hand. If private_data is not set then the driver will
potentially oops with a NULL pointer dereference.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove dead config symbol.
Signed-off-by: Jiri Olsa <olsajiri@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Dooks <ben@fluff.org>
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
with reverting "x86, serial: convert legacy COM ports to platform devices",
we will have the serial console before the port is probled again.
uart_add_one_port==>uart_configure_port==>set_mcttrl(port, 0) will clear
the DTR setting by uart_set_options(). then I will lose my output from
serial console again.
So try to keep DTR in uart_configure_port()
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andi Kleen <ak@suse.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove kio_addr_t, and replace it with unsigned int. No known architecture
needs more than 32 bits for IO addresses and ports and having a separate type
for it is just messy.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently early kernel messages, i.e., those from uncompression, go to the
debugging UART. And if it is enabled in the platform configuration, but
not initialized by the bootloader, the machine hangs, waiting for UART
status change. Besides, having those messages on another UART - typically
the console UART - may be preferrable. This patch allows selecting the
UART in kernel configuration.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/serial/21285.c: In function 'serial21285_set_termios':
drivers/serial/21285.c:280: error: 'tty' undeclared (first use in this function)
drivers/serial/21285.c:280: error: (Each undeclared identifier is reported only once
drivers/serial/21285.c:280: error: for each function it appears in.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use container_of() instead of assuming local uart struct is first member
of uart_port struct.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use IRQF_DISABLED instead of obsolete IRQ_FLG_STD for request_irq() flags
in m68328serial.c driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add configure support for new ColdFire serial driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add build support for new ColdFire serial driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename commproc.[ch] to cpm1.[ch] to be more consistent with cpm2. Also
rename cpm2_common.c to cpm2.c as suggested by Scott Wood. Adjust the
includes accordingly.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds support for the SH7263 (SH-2A) CPU.
This particular CPU is a superset of SH7203, adding some additional
peripheral blocks and hooking up additional (reserved on SH7203)
vectors in the INTC block.
No visibly nasty surprises, yet..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update MPC5200 drivers to also look for compatible properties in the
form "fsl,mpc5200-*" to better conform to open firmware generic names
recommended practice as published here:
http://www.openfirmware.org/1275/practice/gnames/gnamv14a.html
This patch should *not* break compatibility with older device trees
which do not use the 'fsl,' prefix. The drivers will still bind against
the older names also.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently reports back the requested rate not the result of the divides
but thats an easy fix for someone with h/w
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IBM icom serial driver is using a kobject only for reference
counting, nothing else. So switch it to use a kref instead, which is
all that is needed, and is much smaller.
Cc: Anton Blanchard <anton@au.ibm.com>
Cc: Paul Mackerras <paulus@au.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ryan S. Arnold <rsa@us.ibm.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Maciej W. Rozycki