arch/mips/dec/promcon.c:37: ERROR: that open brace { should be on the previous line
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1270/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/pmc-sierra/yosemite/ht-irq.c:38: ERROR: code indent should use tabs where possible
arch/mips/pmc-sierra/yosemite/ht-irq.c:39: ERROR: code indent should use tabs where possible
arch/mips/pmc-sierra/yosemite/ht-irq.c:40: ERROR: code indent should use tabs where possible
arch/mips/pmc-sierra/yosemite/ht-irq.c:43: ERROR: code indent should use tabs where possible
arch/mips/pmc-sierra/yosemite/ht-irq.c:44: ERROR: code indent should use tabs where possible
arch/mips/pmc-sierra/yosemite/ht-irq.c:45: ERROR: code indent should use tabs where possible
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1268/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace phys_to_dma()/dma_to_phys() looping algorithm with an O(1) algorithm
The approach taken is inspired by the sparse memory implementation: take a
certain number of high-order bits off the address them, use this as an
index into a table containing an offset to the desired address and add
it to the original value. There is a table for mapping physical addresses
to DMA addresses and another one for the reverse mapping. The table sizes
depend on how fine-grained the mappings need to be; Coarser granularity
less to smaller tables. On a processor with 32-bit physical and DMA
addresses, with 4 MIB granularity, memory usage is two 2048-byte arrays.
Each 32-byte cache line thus covers 64 MiB of address space.
Also, renames phys_to_bus() to phys_to_dma() and bus_to_phys() to
dma_to_phys() to align with kernel usage.
[Ralf: Fixed silly build breakage due to stackoverflow warning caused by
huge array on stack.]
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1257/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/alchemy/mtx-1/board_setup.o
{standard input}: Assembler messages:
{standard input}:263: Error: opcode not supported on this processor: mips1 (mips1) `sync'
{standard input}:274: Error: opcode not supported on this processor: mips1 (mips1) `sync'
{standard input}:296: Error: opcode not supported on this processor: mips1 (mips1) `sync'
[...]
Any .set mipsX statement other than .set mips0 at the end of inline
assembler is a big fat bug.
Introduced by 9482eabeca315c0276ffb50026b7482481b7097b (linux-mips.org) rsp.
32fd6901a6 (kernel.org).
While at it, fix the same issue in
arch/mips/alchemy/devboards/pb1000/board_setup.c
arch/mips/alchemy/xxs1500/board_setup.c
as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
B43_pci_bridge is needed to use the b43 driver with brcm47xx. Activate it
by default if PCI is available.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1510/
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The previous patch 4a86f2d27733f610e642649aca3e82e86fca9e22 (lmo) rsp.
84a6fcb368 (kernel.org) was wrong.
The BCM47xx architecture maps the ram into a 128MB address space. It
will be spaced there as often as goes into the 128MB. Detection tries to
find the position where the same memory is found. When reading beyond
128MB the processor will throw an exception. If 128MB RAM is installed,
it will not find a memory alias because it tries to read beyond the 128MB
border. Now it just assumes 128MB installed ram if it can not find an
alias.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1508/
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When building with a gcc-4.4.x toolchain that is configured to produce
32-bits executables by default, we will produce __lshrti3 in sched_clock()
which is never resolved so the kernel fails to link. Unconditionally use
the inline assembly version as suggested by David Daney, which works around
the issue.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1514/
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The 'mult' element of struct clock_event_device must never be wider
than 32-bits. If it were, it would get truncated when used by
clockevent_delta2ns() when this calls do_div().
We can meet this requirement by using clockevent_set_clock() to set
the MULT and SHIFT values.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1253/
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The include is unecessary and will when building the IP35 result in
recursive header inclusion spaghetti.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With SLAB, it works without ARCH_KMALLOC_MINALIGN, but with SLOB/SLUB,
ARCH_KMALLOC_MINALIGN is required to ensure alignment of kmalloced
buffer.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1248/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
request_region should be used with release_region, not request_mem_region.
Geert Uytterhoeven pointed out that in the case of drivers/video/gbefb.c,
the problem is actually the other way around; request_mem_region should be
used instead of request_region.
The semantic patch that finds/fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r1@
expression start;
@@
request_region(start,...)
@b1@
expression r1.start;
@@
request_mem_region(start,...)
@depends on !b1@
expression r1.start;
expression E;
@@
- release_mem_region
+ release_region
(start,E)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
SECURITY_APPARMOR should depend on NET since AUDIT needs
(depends on) NET.
Fixes 70-80 errors that occur when CONFIG_NET is not enabled,
but APPARMOR selects AUDIT without qualification. E.g.:
audit.c:(.text+0x33361): undefined reference to `netlink_unicast'
(.text+0x333df): undefined reference to `netlink_unicast'
audit.c:(.text+0x3341d): undefined reference to `skb_queue_tail'
audit.c:(.text+0x33424): undefined reference to `kfree_skb'
audit.c:(.text+0x334cb): undefined reference to `kfree_skb'
audit.c:(.text+0x33597): undefined reference to `skb_put'
audit.c:(.text+0x3369b): undefined reference to `__alloc_skb'
audit.c:(.text+0x336d7): undefined reference to `kfree_skb'
(.text+0x3374c): undefined reference to `__alloc_skb'
auditfilter.c:(.text+0x35305): undefined reference to `skb_queue_tail'
lsm_audit.c:(.text+0x2873): undefined reference to `init_net'
lsm_audit.c:(.text+0x2878): undefined reference to `dev_get_by_index'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: James Morris <jmorris@namei.org>
With the availablility of a sysfs device attribute for examining disk serial
numbers the ioctl is no longer needed. The user-space changes for this aren't
upstream yet so we don't have any users to worry about.
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Create a new attribute for virtio-blk devices that will fetch the serial number
of the block device. This attribute can be used by udev to create disk/by-id
symlinks for devices that don't have a UUID (filesystem) associated with them.
ATA_IDENTIFY strings are special in that they can be up to 20 chars long
and aren't required to be nul-terminated. The buffer is also zero-padded
meaning that if the serial is 19 chars or less that we get a nul-terminated
string. When copying this value into a string buffer, we must be careful to
copy up to the nul (if it present) and only 20 if it is longer and not to
attempt to nul terminate; this isn't needed.
Changes since v1:
- Added BUILD_BUG_ON() for PAGE_SIZE check
- Removed min() since BUILD_BUG_ON() handles the check
- Replaced serial_sysfs() by copying id directly to buffer
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
Signed-off-by: john cooper <john.cooper@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If we want to support barriers with the cache=writethrough mode in qemu
we need to tell the block layer that we only need queue drains to
implement a barrier. Follow the model set by SCSI and IDE and assume
that there is no volatile write cache if the host doesn't advertize it.
While this might imply working barriers on old qemu versions or other
hypervisors that actually have a volatile write cache this is only a
cosmetic issue - these hypervisors don't guarantee any data integrity
with or without this patch, but with the patch we at least provide
data ordering.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
On my (32-bit x86) machine, sys_init_module() uses 124 bytes of stack
once load_module() is inlined.
This effectively reverts ffb4ba76 which inlined it due to stack
pressure.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This simply hoists more code out of load_module; we also put the
identification of the extable and dynamic debug table in with the
others in find_module_sections().
We move the taint check to the actual add/remove of the dynamic debug
info: this is certain (find_module_sections is too early).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Yehuda Sadeh <yehuda@hq.newdream.net>
Instead of copying and allocating the args and storing it in
load_info, we can just allocate them right before we need them.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Pass the struct load_info into all the other functions in module
loading. This neatens things and makes them more consistent.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Restore the stub module_remove_modinfo_attrs, remove the now-unused
!CONFIG_SYSFS module_sysfs_init.
Also, rename mod_kobject_remove() to mod_sysfs_teardown() as
it is the logical counterpart to mod_sysfs_setup now.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We change the sysfs functions to take struct load_info, and call
them all in mod_sysfs_setup().
We also clean up the #ifdefs a little.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
layout_and_allocate() does everything up to and including the final
struct module placement inside the allocated module memory. We have
to store the symbol layout information in our struct load_info though.
This avoids the nasty code we had before where 'mod' pointed first
to the version inside the temporary allocation containing the entire
file, then later was moved to point to the real struct module: now
the main code only ever sees the final module address.
(Includes fix for the Tony Luck-found Linus-diagnosed failure path
error).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Andrew had the sole pleasure of tickling this bug in linux-next; when we set
up "info->strtab" it's pointing into the temporary copy of the module. For
most uses that is fine, but kallsyms keeps a pointer around during module
load (inside mod->strtab).
If we oops for some reason inside a module's init function, kallsyms will use
the mod->strtab pointer into the now-freed temporary module copy.
(Later oopses work fine: after init we overwrite mod->strtab to point to a
compacted core-only strtab).
Reported-by: Andrew "Grumpy" Morton <akpm@linux-foundation.org>
Signed-off-by: Rusty "Buggy" Russell <rusty@rustcorp.com.au>
Tested-by: Andrew "Happy" Morton <akpm@linux-foundation.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Put all the "rewrite and check section headers" in one place. This
adds another iteration over the sections, but it's far clearer. We
iterate once for every find_section() so we already iterate over many
times.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Btw, here's a patch that _looks_ large, but it really pretty trivial, and
sets things up so that it would be way easier to split off pieces of the
module loading.
The reason it looks large is that it creates a "module_info" structure
that contains all the module state that we're building up while loading,
instead of having individual variables for all the indices etc.
So the patch ends up being large, because every "symindex" access instead
becomes "info.index.sym" etc. That may be a few characters longer, but it
then means that we can just pass a pointer to that "info" structure
around. and let all the pieces fill it in very naturally.
As an example of that, the patch also moves the initialization of all
those convenience variables into a "setup_module_info()" function. And at
this point it really does become very natural to start to peel off some of
the error labels and move them into the helper functions - now the
"truncated" case is gone, and is handled inside that setup function
instead.
So maybe you don't like this approach, and it does make the variable
accesses a bit longer, but I don't think unreadably so. And the patch
really does look big and scary, but there really should be absolutely no
semantic changes - most of it was a trivial and mindless rename.
In fact, it was so mindless that I on purpose kept the existing helper
functions looking like this:
- err = check_modinfo(mod, sechdrs, infoindex, versindex);
+ err = check_modinfo(mod, info.sechdrs, info.index.info, info.index.vers);
rather than changing them to just take the "info" pointer. IOW, a second
phase (if you think the approach is ok) would change that calling
convention to just do
err = check_modinfo(mod, &info);
(and same for "layout_sections()", "layout_symtabs()" etc.) Similarly,
while right now it makes things _look_ bigger, with things like this:
versindex = find_sec(hdr, sechdrs, secstrings, "__versions");
becoming
info->index.vers = find_sec(info->hdr, info->sechdrs, info->secstrings, "__versions");
in the new "setup_module_info()" function, that's again just a result of
it being a search-and-replace patch. By using the 'info' pointer, we could
just change the 'find_sec()' interface so that it ends up being
info->index.vers = find_sec(info, "__versions");
instead, and then we'd actually have a shorter and more readable line. So
for a lot of those mindless variable name expansions there's would be room
for separate cleanups.
I didn't move quite everything in there - if we do this to layout_symtabs,
for example, we'd want to move the percpu, symoffs, stroffs, *strmap
variables to be fields in that module_info structure too. But that's a
much smaller patch, I moved just the really core stuff that is currently
being set up and used in various parts.
But even in this rough form, it removes close to 70 lines from that
function (but adds 22 lines overall, of course - the structure definition,
the helper function declarations and call-sites etc etc).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
And now that I'm looking at that call-chain (to see if it would make sense
to use some other more specific lock - doesn't look like it: all the
readers are using RCU and this is the only writer), I also give you this
trivial one-liner. It changes each_symbol() to not put that constant array
on the stack, resulting in changing
movq $C.388.31095, %rsi #, tmp85
subq $376, %rsp #,
movq %rdi, %rbx # fn, fn
leaq -208(%rbp), %rdi #, tmp84
movq %rbx, %rdx # fn,
rep movsl
xorl %esi, %esi #
leaq -208(%rbp), %rdi #, tmp87
movq %r12, %rcx # data,
call each_symbol_in_section.clone.0 #
into
xorl %esi, %esi #
subq $216, %rsp #,
movq %rdi, %rbx # fn, fn
movq $arr.31078, %rdi #,
call each_symbol_in_section.clone.0 #
which is not so much about being obviously shorter and simpler because we
don't unnecessarily copy that constant array around onto the stack, but
also about having a much smaller stack footprint (376 vs 216 bytes - see
the update of 'rsp').
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
1) Extract out the relocation loop into apply_relocations
2) Extract license and version checks into check_module_license_and_versions
3) Extract icache flushing into flush_module_icache
4) Move __obsparm warning into find_module_sections
5) Move license setting into check_modinfo.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Allocate references inside module_unload_init(), clean up inside
module_unload_free().
This version fixed to do allocation before __this_cpu_write, thanks to
bug reports from linux-next from Dave Young <hidave.darkstar@gmail.com>
and Stephen Rothwell <sfr@canb.auug.org.au>.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Here's a second one. It's slightly less trivial - since we now have error
cases - and equally untested so it may well be totally broken. But it also
cleans up a bit more, and avoids one of the goto targets, because the
"move_module()" helper now does both allocations or none.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
I'd start from the trivial stuff. There's a fair amount of straight-line
code that just makes the function hard to read just because you have to
page up and down so far. Some of it is trivial to just create a helper
function for.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
No need to clear mod->refptr in module_unload_init(), since
alloc_percpu() already clears allocated chunks.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (removed unused var)
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This restricts the use of the big kernel lock to the i830 and i810
device drivers. The three remaining users in common code (open, ioctl
and release) get converted to a new mutex, the drm_global_mutex,
making the locking stricter than the big kernel lock.
This may have a performance impact, but only in those cases that
currently don't use DRM_UNLOCKED flag in the ioctl list and would
benefit from that anyway.
The reason why i810 and i830 cannot use drm_global_mutex in their
mmap functions is a lock-order inversion problem between the current
use of the BKL and mmap_sem in these drivers. Since the BKL has
release-on-sleep semantics, it's harmless but it would cause trouble
if we replace the BKL with a mutex.
Instead, these drivers get their own ioctl wrappers that take the
BKL around every ioctl call and then set their own handlers as
DRM_UNLOCKED.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
In most use cases the driver will be using the same static config all
the time: interpreting i2c_board_info::platform_data as the default
config we can can save the GPU driver a redundant set_config() call.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is required should we ever attempt to use an io-mapping where
KM_USER0 is verboten, such as inside an IRQ context.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
R4xx also uses the atom add connector function, but underscan is only
supported on avivo chips.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Andrea Gelmini