After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The MC13783 Chip Errata, Rev. 4 says, that depending on SPI clock
and main audio clock speed, the Audio Codec or Stereo DAC do sometimes
not start when programmed to do so. This is due to an internal clock
timing issue related to the loading of the SPI bits into the audio block.
On an i.MX27 based system, this issue lead to switched audio channels under
certain circumstances: RTC + Touch + Audio are used and loaded at startup.
The mentioned workaround of writing registers 40 and 41 two times is implemented
here.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Mark Brown <broonie@linaro.org>
MacBook 6,1 and 6,2 have a CS4208 codec instead of CS4206/CS4207 on
the former models. Most of functions work fine as is, except for the
silent speaker output. After debugging sessions, it turned out that
the machine needs to set GPIO 0 for the speaker amp.
This patch adds the basic support for CS4208 and the fixup for these
MacBooks. Basically the codec works just with the generic parser.
For re-using the existing GPIO amp code and init/free callbacks, a few
places have been changed so that CS4206/4207-specific codes (errata,
etc) won't hit with CS4208.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60811
Reported-and-tested-by: Imre Kaloz <kaloz@openwrt.org>
Reported-and-tested-by: Ian Munsie <darkstarsword@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Toshiba Satellite C870 shows interrupt problems occasionally when
certain mixer controls like "Mic Switch" is toggled. This seems
worked around by not using MSI.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=833585
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The S/PDIF driver needs regmap so select it to make sure it gets
included in the build.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When Gfx driver reconnects a port and transcoder, the pin amplifier will
be muted. To enable sound, the pin amp need to be unmuted.
This patch
- moves pin amp unmuting from stream preparing to hdmi_setup_audio_infoframe().
So if port:transcoder reconnection happens during stream playback, the ELDV
unsol event can stil trigger pin's amp unmuting when re-setting up audio
info frame.
- remove reading pin amp status before unmuting for speed-up, since pin amp
should always be unmuted.
- rename haswell_verify_pin_D0() to haswell_verify_D0(), since the convertor
power state is also fixed here.
This patch is mostly based on suggestion of David Henningsson.
Cc: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To apply Haswell specific fixings, this patch defines is_haswell() to check
whether a display audio codec is Haswell, to avoid explicitly checking Haswell
vendor ID everywhere.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS TX300 has a built-in speaker in the tablet part and in the dock
part, and the tablet speaker is supposed to be unused while the
machine is docked. The current HD-audio driver, however, doesn't
support the dock speaker, partly because BIOS doesn't set up the pin
for the corresponding output.
But, not only the missing pin config, also the missing unsol event
handling is another issue. Otherwise the automatic switching via
dock/undock won't work.
Through debugging sessions, we found out that the dock speaker pin is
NID 0x1b, and it generates an unsol event at docking/undocking, the
docking state can be inquired via the normal pin detection verb.
Also, it's turned out that GPIO 2 is needed as an amp. So, all
materials are ready to cook.
This patch provides the basic dock speaker support with TX300:
- The dock speaker is turned on/off via "Dock Speaker" mixer mute.
- The dock speaker is automatically muted when docked. This is
independently from the mixer mute switch, just like the headphone
auto-mute function.
The implementation is a bit tricky. Since we want to handle it as a
secondary speaker, we set it up a pin as a speaker with a jack
detection. Then, the fixup function registers the own unsol callback
for this pin because the standard automute can't handle the thing like
a "speaker jack". In the own automute hook, we apply the mute of the
tablet speaker in addition by checking the dock state.
Also, the speaker control names are slightly shuffled because the
generic parser doesn't give good names but blindly assumes a bass
speaker as a secondary speaker.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59791
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The compatible string of the kirkwood-i2s driver was chosen as
"marvell,mvebu-audio". Using such a compatible string is not a good
idea, since "mvebu" is the name of a large family of SOCs, in which
new, unknown SOCs will be coming in the future. It is therefore
impossible to know what will be evolutions of this hardware block in
the next generations of the SOCs. For this reason, the recommandation
for compatible strings of on-SOCs devices has always been to use the
name of the oldest SOC that has the hardware block. New SOCs that have
an exactly compatible hardware block can reference it using the same
compatible string. See [1], [2] and [3] for various cases were this
suggestion was made, including from Rob Herring, a Device Tree binding
maintainer.
As an example, there are already small differences between current
generations:
* On Kirkwood, only one interrupt is used for audio.
* On Dove, two interrupts are used, one for audio data and one for
error reporting.
In the near future, I'll be adding audio support to Armada 370, which
allows has the same hardware block (but maybe with minor variants).
Therefore, this patch changes the driver to accept
"marvell,kirkwood-audio" and "marvell,dove-audio" as compatible
strings instead of the too-generic "marvell,mvebu-audio". The reason
for the two different compatible strings is the difference in the
number of interrupts used by the two SOCs for audio.
This Device Tree binding has never been part of a Linux kernel stable
release so far, so it can be changed now without breaking backward
compatibility.
[1] http://lists.infradead.org/pipermail/linux-mtd/2012-March/040417.html
[2] http://lists.infradead.org/pipermail/linux-arm-kernel/2013-April/161065.html
[3] http://lists.infradead.org/pipermail/linux-arm-kernel/2012-March/087702.html
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As once the error interrupt is triggered, it can not be cleared.
So, disable it.
No side effect found while testing on sama5d3xek and at91sam9x5ek
boards.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Booting a mx51babbage board with a non-dt kernel leads to the following crash:
Unable to handle kernel NULL pointer dereference at virtual address 0000001c
pgd = 80004000
[0000001c] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.11.0-next-20130903 #287
task: 9f860000 ti: 9f862000 task.ti: 9f862000
PC is at of_get_next_available_child+0x5c/0x68
LR is at of_get_next_available_child+0x1c/0x68
pc : [<8043ea58>] lr : [<8043ea18>] psr: 60000193
sp : 9f863d58 ip : 00000000 fp : 9f863d74
r10: 9f89a010 r9 : 9f862000 r8 : 807bb26c
r7 : 80615d5c r6 : 00000000 r5 : 60000113 r4 : 00000000
r3 : 00000000 r2 : 808770a4 r1 : 00000011 r0 : 60000113
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5387d Table: 90004019 DAC: 00000017
Process swapper/0 (pid: 1, stack limit = 0x9f862240)
Stack: (0x9f863d58 to 0x9f864000)
This is caused by commit 8548a464b9 (ASoC: imx-audmux: Read default
configuration from devicetree).
In order to fix this, add a check for 'of_id' so that
imx_audmux_parse_dt_defaults() only gets called when a dt kernel is running.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When the transcoder:port mapping on Haswell HDMI/DP audio is changed
during the stream playback, the sound gets lost. Typically this
problem is seen when the user switches the graphics mode from eDP+DP
to DP-only configuration, where CRTC 1 is used for DP in the former
while CRTC 0 is used for the latter.
The graphics controller notifies the change via the normal ELD update
procedure, so we get the intrinsic event. For enabling the sound
again, the HDMI audio driver needs to reset the pin and set up the
audio infoframe again.
This patch achieves it by:
- keep the current status of channels and info frame setup in per_pin
struct,
- check the reconnection in the intrinsic event handler,
- reset the pin and the re-invoke hdmi_setup_audio_infoframe()
accordingly.
The hdmi_setup_audio_infoframe() function has been changed, too, so
that it can be invoked without passing the substream instance.
The patch is mostly based on the work by Mengdong Lin.
Cc: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdmi_channel_allocation() tries to find a HDMI channel allocation that
matches the number channels in the playback stream and contains only
speakers that the HDMI sink has reported as available via EDID. If no
such allocation is found, 0 (stereo audio) is used.
Using CA 0 causes the audio causes the sink to discard everything except
the first two channels (front left and front right).
However, the sink may be capable of receiving more channels than it has
speakers (and then perform downmix or discard the extra channels), in
which case it is preferable to use a CA that contains extra channels
than to use CA 0 which discards all the non-stereo channels.
Additionally, it seems that HBR (HD) passthrough output does not work on
Intel HDMI codecs when CA is set to 0 (possibly the codec zeroes
channels not present in CA). This happens with all receivers that report
a 5.1 speaker mask since a HBR stream is carried on 8 channels to the
codec.
Add a fallback in the CA selection so that the CA channel count at least
matches the stream channel count, even if the stream contains channels
not present in the sink speaker descriptor.
Thanks to GrimGriefer at OpenELEC forums for discovering that changing
the sink speaker mask allowed HBR output.
Reported-by: GrimGriefer
Reported-by: Ashecrow
Reported-by: Frank Zafka <kafkaesque1978@gmail.com>
Reported-by: Peter Frühberger <fritsch@xbmc.org>
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On a mx28 board, running "aplay -l" and "arecord -l" results in the following:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 0: Playback sgtl5000-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: mxssgtl5000 [mxs_sgtl5000], device 1: Capture sgtl5000-1 []
Subdevices: 1/1
Subdevice #0: subdevice #0
$ arecord -l
**** List of CAPTURE Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 0: Playback sgtl5000-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: mxssgtl5000 [mxs_sgtl5000], device 1: Capture sgtl5000-1 []
Subdevices: 1/1
Subdevice #0: subdevice #0
,which is not correct because we got a capture device listed in aplay and a
playback device listed in arecord.
On mx28 there are two serial audio interface ports (SAIF0 and SAIF1) and each
one of them are unidirectional.
Allow to specify a dai link as 'playback_only' or 'capture_only', which suits
well for this case.
After this change we can correctly report the capabilities as follows:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 0: HiFi Playback sgtl5000-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
$ arecord -l
**** List of CAPTURE Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 1: HiFi Capture sgtl5000-1 []
Subdevices: 1/1
Subdevice #0: subdevice #0
Also tested playback and capture on the mx28evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add 'playback_only' and 'capture_only' fields that can be used for specifying
that a dai_link has a unidirectional capability.
The motivation for this is for the cases of systems, such as Freescale MX28,
that has two unidirectional DAIs.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ssm2602 uses regmap for caching not soc-cache, so we need to use
regcache_sync() instead of snd_soc_cache_sync().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a blank space missing between ':=' and 'imx-spdif.o', thus add it.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We need to make sure that the control's cached value is initialized to the same
value as the control's widget->on_val. Otherwise updates might be lost.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SND_SOC_FSL_UTILS is only used by PowerPC machines, so let's drop it in the
i.mx case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The legacy S3C-DMA API required every period of a cyclic buffer to be
queued separately. After conversion of Samsung ASoC to Samsung DMA
wrappers somebody made an assumption that the same is needed for DMA
engine API, which is not true.
In effect, Samsung ASoC DMA code was queuing the whole cyclic buffer
multiple times with a shift of one period per iteration, leading to:
a) severe memory waste - up to 13x times more DMA transfer descriptors
are allocated than needed,
b) possible memory corruption, because further cyclic buffers were out
of the original buffers, due to the offset.
This patch fixes this problem by making the legacy S3C-DMA API use the
same semantics as DMA engine (the whole cyclic buffer is enqueued at
once) and modifying users of Samsung DMA wrappers in cyclic mode to
behave appropriately.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Driver core clears the driver data to NULL after device_release or on probe
failure, so just remove it from here.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Driver core clears the driver data to NULL after device_release or on probe
failure, so just remove it from here.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch implements a device-tree-only machine driver for Freescale
i.MX series Soc. It works with spdif_transmitter/spdif_receiver and
fsl_spdif.c drivers.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for HDMI audio device on VGA cards that powerdown
to D3cold using non-standard ACPI/PCI infrastructure (optimus).
This does a couple of things to make it work:
a) add a set of power ops for the hdmi domain, and enables them
via vga_switcheroo when we are a switcheroo controlled card. This
just replaces the runtime resume operation so that when the card
is in D3cold the userspace pci config space access via sysfs,
the vga switcheroon runtime resume gets called first and it calls
the GPU resume callback before calling the sound card runtime
resume.
b) standard ACPI/PCI stacks won't put a device into D3cold without
an ACPI handle, but since the hdmi audio devices on gpus don't have
an ACPI handle, we need to manually force the device into D3cold
after suspend from the switcheroo path only.
c) don't try and do runtime s/r when the GPU is off.
d) call runtime suspend/resume during switcheroo suspend/resume
this is to make sure the runtime stack knows to try and resume
the hdmi audio device for pci config space access.
v2: fix incorrect runtime call suspend->resume.
v3: rework irq handler to avoid false irq when we are resuming
but haven't runtime resumed yet, don't bother trying D3cold,
it won't work, just set it manually ourselves, move runtime s/r
calls outside the main s/r hook. enable dnyamic pm properly by
dropping reference.
v4: put back irq handler check just wrap it with cap check
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The recent commit to delay the release of kobject triggered NULL
dereferences of opti9xx drivers. The cause is that all
snd-opti92x-ad1848, snd-opti92x-cs4231 and snd-opti93x drivers
register the PnP card driver with the very same name, and also
snd-opti92x-ad1848 and -cs4231 drivers register the ISA driver with
the same name, too. When these drivers are built in, quick
"register-release-and-re-register" actions occur, and this results in
Oops because of the same name is assigned to the kobject.
The fix is simply to assign individual names. As a bonus, by using
KBUILD_MODNAME, the patch reduces more lines than it adds.
The fix is based on the suggestion by Russell King.
Reported-and-tested-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch permits the generation of the Kirkwood audio driver which
may be used in the Dove boards.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_dapm_new_widgets() works on the ASoC card as a whole not on a specific
DAPM context. The DAPM context that is passed as the parameter is only used to
look up the pointer to the card. This patch updates the signature of
snd_soc_dapm_new_widgets() to take the card directly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Call snd_soc_dapm_new_widgets() before the auto non-connected pins have been
marked as not connected will power the system under the assumption that those
pins are connected. Once the pins have been marked as disconnected the system
there will be an additional power run. This can cause unnecessary power
transitions. Calling snd_soc_dapm_new_widgets() only after the pins have been
marked as non-connected avoids this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Each time snd_soc_dapm_new_widgets() is called it will instantiate all the
widgets and routes that have been added so far and then power them. Doing this
multiple times before the card is fully initialized and all widgets have been
added can cause unnecessary and even invalid power state transitions which can
result in extra register writes and and also might cause clicks and pops.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_jack_add_pins() does not create any new DAPM widgets, so there is no
need to call snd_soc_dapm_new_widgets().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The core will call snd_soc_dapm_new_widgets() once all components of the card
have been initialized, so there is no need to do this manually in the driver.
Calling it earlier also might result in a partially instantiated system being
powered up which cause undesired side effects.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Let the core take care of instantiating the controls and DAPM widgets and
routes, this makes the code a bit shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The current calls to dapm_mark_dirty() in snd_soc_dapm_add_path() are on a path
that is only reached if the sink widget is either a mixer or a mux. Move the
calls further up so they are called for all widget types.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Let the core take care of instantiating the DAPM widgets and routes, this makes
the code a bit shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
CONFIG_SND_HDA_I915 doesn't have to be user-selectable as this is almost
mandatory when i915 driver is available. Let's enable it always when
CONFIG_DRM_I915 is set, so that user won't be bothered by useless
questions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds two fields to unsolicited response, according to spec HDA040-A:
- Device Entry (bit 20:15)
- Inactive (bit 2)
and show the info in debug message.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch is only to allow codec proc file to expose devices list/select info
for Haswell codec pins.
Since Haswell Gfx driver cannot support DP1.2 MST now, so all pins' device list
is empty, meaning no pin is multi-streaming capaple.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a display codec supports multi-stream transport on the pins, the pin's
device list length and device entries will be exposed to codec proc file.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds flags and routines to get device list & selection info on
a pin.
To support Display Port 1.2 multi-stream transport (MST) over single DP port,
a pin can support multiple devices. Please refer to HD-A spec Document Change
Notificaton HDA040-A.
A display audio codec can set flag "dp_mst" in its patch, indicating its pins
can support MST. But at runtime, a pin may not be multi-streaming capable and
report the device list is empty, depending on Gfx driver configuration.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Using 0x%# emits 0x0x. Only one is necessary.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Driver core clears the driver data to NULL after device_release or on probe
failure, so just remove it from here.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current FSI is supporting DMAEngine transfer,
but, it needs to use work queue.
Therefore, DMA transfer settings might be late if there is heavy task.
This patch reserves next period beforehand on DMA transfer function.
Android sound will be breaking up without this patch.
Tested-by: Tomohito Esaki <etom@igel.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove the "====" pattern to let the comments cleaner and more uniform.
Also, do not use multi-line style for a single line comment.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Driver core clears the driver data to NULL after device_release or on probe
failure, so just remove it from here.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As reported by kbuild test robot <fengguang.wu@intel.com>:
warning: (SND_ES1968_RADIO && SND_FM801_TEA575X_BOOL) selects RADIO_TEA575X which has unmet direct dependencies (MEDIA_SUPPORT && RADIO_ADAPTERS && VIDEO_V4L2)
That happens because a radio driver is selected, without selecting the
RADIO_ADAPTERS menu.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Martin Schwidefsky