This patch (as738b) fixes numerous problems in the controller/root-hub
suspend/resume/remote-wakeup support in ehci-hcd:
The bus_resume() routine should wake up only the ports that
were suspended by bus_suspend(). Ports that were already
suspended should remain that way.
The interrupt mask is used to detect loss of power in the
bus_resume() routine (if the mask is 0 then power was lost).
However bus_suspend() always sets the mask to 0. Instead the
mask should retain its normal value, with port-change-detect
interrupts disabled if remote wakeup is turned off.
The interrupt mask should be reset to its correct value at the
end of bus_resume() regardless of whether power was lost.
bus_resume() reinitializes the operational registers if power
was lost. However those registers are not in the aux power
well, hence they can lose their values whenever the controller
is put into D3. They should always be reinitialized.
When a port-change interrupt occurs and the root hub is
suspended, the interrupt handler should request a root-hub
resume instead of starting up the controller all by itself.
There's no need for the interrupt handler to request a
root-hub resume every time a suspended port sends a
remote-wakeup request.
The pci_resume() method doesn't need to check for connected
ports when deciding whether or not to reset the controller.
It can make that decision based on whether Vaux power was
maintained.
Even when the controller does not need to be reset,
pci_resume() must undo the effect of pci_suspend() by
re-enabling the interrupt mask.
If power was lost, pci_resume() must not call ehci_run().
At this point the root hub is still supposed to be suspended,
not running. It's enough to rewrite the command register and
set the configured_flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts 26f953fd88 which caused
resume problems on the mac mini.
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This revamps handling of the hardware "async advance" IRQ, and its watchdog
timer. Basically it dis-entangles that important timeout from the others,
simplifying the associated state and code to make it more robust.
This reportedly improves behavior of EHCI on some systems with VIA chips,
and AFAIK won't affect non-VIA hardware. VIA systems need this code to
recover from silcon bugs whereby the "async advance" IRQ isn't issued.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ ... when you have an editor set to remind you of whitespace bugs ... ]
Cosmetic EHCI changes: remove end-of-line whitespace, spaces before tabs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If some problem occurs during ehci startup, for instance, request_irq fails,
echi hcd driver tries it best to cleanup, but fails to unregister reboot
notifier, which in turn leads to crash on reboot/poweroff.
The following patch resolves this problem by not using reboot notifiers
anymore, but instead making ehci/ohci driver get its own shutdown method. For
PCI, it is done through pci glue, for everything else through platform driver
glue.
One downside: sa1111 does not use platform driver stuff, and does not have its
own shutdown hook, so no 'shutdown' is called for it now. I'm not sure if it
is really necessary on that platform, though.
Signed-off-by: Aleks Gorelov <dared1st@yahoo.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On the MPC834x processors the multiport host (MPH) EHCI controller has an
erratum in which the port number in the queue head expects to be 0..N-1
instead of 1..N. If we are on one of these chips we subtract one from
the port number before putting it into the queue head.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This teaches the EHCI driver about a quirk seen in older NForce2 chips,
adding a workaround to ignore selective suspend requests. Bus-wide
(so-called "global") suspend still works, as does USB wakeup of a
root hub that's globally suspended.
There's still a hole in this support though. Strictly speaking, this
should _fail_ selective suspend requests, rather than ignoring them,
since doing it this way means that devices which should be able to issue
remote wakeup are not going to be able to do that. For now, we'll just
live with that problem ... since usbcore expects to do selective suspend
on the way towards a full bus suspend, and usbcore needs to be able to
do full bus suspend.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This splits BIOS and PCI specific support out of ehci-hcd.c into
ehci-pci.c. It follows the model already used in the OHCI driver
so support for non-PCI EHCI controllers can be more easily added.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/ehci-hcd.c | 543 ++++++--------------------------------------
drivers/usb/host/ehci-pci.c | 414 +++++++++++++++++++++++++++++++++
drivers/usb/host/ehci.h | 1
3 files changed, 492 insertions(+), 466 deletions(-)
One change may improve some S1 or S3 resume cases, and the other
seems mostly to explain some strange state "lsusb" would show.
Two fixes:
- On resume, don't think about resuming any unpowered port, or
resetting any port with OWNER set to the OHCI/UHCI companion.
This will make some S1 and S3 resume scenarios work better.
- PORT_CSC was not being cleared correctly in ehci_hub_status_data.
This was visible at least through current versions of "lsusb",
and might have caused some other hub related strangeness.
The fix addresses all three write-to-clear bits, using the same
approach that UHCI happens to use: a mask of bits that are
cleared in most writes to that port status register.
Original patch seems to have been from from William.Morrow@amd.com
and this version (from David) finishes the write-to-clear changes.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the field tt_usecs to ehci_qh and ehci_iso_stream, and sets it
appropriately when setting them up as periodic endpoints. It records
the transation translator's think_time (added in last patch) plus the
downstream (i.e. low or full speed) bustime of the transfer associated
with each interrupt or iso frame, as calculated by usb_calc_bus_time.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch has a one line oops fix, plus related cleanups.
- The bugfix uses microframe scheduling data given to the hardware to
test "is this a periodic QH", rather than testing for nonzero period.
(Prevents an oops by providing the correct answer.)
- The cleanup going along with the patch should make it clearer what's
going on whenever those bitfields are accessed.
The bug came about when, around January, two new kinds of EHCI interrupt
scheduling operation were added, involving both the high speed (24 KBytes
per millisec) and low/full speed (1-64 bytes per millisec) microframe
scheduling. A driver for the Edirol UA-1000 Audio Capture Unit ran into
the oops; it used one of the newly supported high speed modes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Miscellaneous updates for EHCI.
- Mostly updates the power switching on EHCI controllers. One routine
centralizes the "power on/off all ports" logic, and the capability to
do that is reported more correctly.
- Courtesy Colin Leroy, a patch to always power up ports after resumes
which didn't keep a USB device suspended. The reset-everything logic
powers down those ports (on some hardware) so something needs to turn
them back on.
- Minor tweaks/bugfixes for the debug port support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch includes minor "sparse -Wbitwise" updates for the PCI based
HCDs. Almost all of them involve just changing the second parameter of the
suspend() method to a pm_message_t ... the others relate to how the EHCI
code walks in-memory data structures. (There's a minor bug fixed there too
... affecting the big-endian sysfs async schedule dump.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/drivers/usb/core/hcd.h
===================================================================
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Alan Stern