Usually we get all the values we wanted but it is possible, that te ADC
unit is busy performing the conversation for the HW events. In that case
-EBUSY is returned and the user may re-call the function.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The TSC part allows to specify the input lines. The IIO part assumes
that it usues always the last few, that means if IIO has adc-channels
set to 2 it will use channel 6 and 7. However it might make sense to use
only 6.
This patch changes the device property (which was introduced recently
and was never in an official release) in a way that the user can specify
which of the AIN lines should be used. In Addition to this, the name is
now AINx where x is the channel number i.e. for AIN6 we would have 6.
Prior this, it always started counting at 0 which is confusing. In
addition to this, it also checks for correct step number during reading
and does not rely on proper FIFO depth.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The driver programs a threshold of "coordinate_readouts" say 5. The
REG_FIFO0THR registers says it should it be programmed to "threshold
minus one". The driver does not expect just 5 coordinates but 5 * 2 + 2.
Multiplied by two because 5 for X and 5 for Y and plus 2 because we have
two Z.
The whole thing kind of works because It reads the 5 coordinates for X
and Y from FIFO0 and FIFO1 and the last element in each FIFO is ignored
within the loop and read later.
Nothing guaranties that FIFO1 is ready by the time it is read. In fact I
could see that that FIFO1 reaturns for Y channels 8,9, 10, 12, 6 and for
Y channel 7 for Z. The problem is that channel 7 and channel 12 got
somehow mixed up.
The other Problem is that FIFO1 is also used by the IIO part leading to
wrong results if both (tsc & adc) are used.
The patch tries to clean up the whole thing a little:
- Remove the +1 and -1 in REG_STEPCONFIG, REG_STEPDELAY and its counter
part in the for loop. This is just confusing.
- Use only FIFO0 in TSC. The fifo has space for 64 entries so should be
fine.
- Read the whole FIFO in one function and check the channel.
- in case we dawdle around, make sure we only read a multiple of our
coordinate set. On the second interrupt we will cleanup the remaining
enties.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
TI-adc reads a little better compared to tiadc. And if we add am335x to
it then we have the same naming scheme as the tsc side.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
This patch provides the members "datasheet_name" and scan_type. This is
the remaining part of the earlier patch where I (bigeasy) removed iio_map
because it is now supplied by the device tree. It also static names as
suggested by Jonathan.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
This patch removes access to platform data mfd_tscadc_board because the
platform is DT only.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Add DT support for client ADC driver.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Current code has hard coded value written to
step enable bits. Now the bits are updated based
on how many steps are needed to be configured got
from platform data.
The user needs to take care not to exceed
the count more than 16. While using ADC and TSC
one should take care to set this parameter correctly.
Sebastian added the common lock and moved the code, that manipulates the
steps, from into the mfd module.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The mfd driver creates platform data for the child devices and it is the
ti_tscadc_dev struct. This struct is copied for the two devices.
The copy of the structure makes a common lock in this structure a little
less usefull. Therefore the platform data is not a pointer to the
structure and the same structure is used.
While doing the change I noticed that the suspend/resume code assumes
the wrong pointer for ti_tscadc_dev and this has been fixed as well.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The adis16130 driver is fairly simple and it a good shape now, so move it out of
staging. Remove an outdated FIXME along the way.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for the AD7303. The AD7303 is a simple 2 channel 8 bit
DAC with an SPI interface.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Per review feedback from Lars-Peter Clausen <lars@metafoo.de>
Changes since V1:
Fix return value handling of adf4350_parse_dt()
Use of_get_gpio
Avoid abbreviations in devicetree properties
Fix typo in docs
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The name includes irq_res->start which of type resource_size_t not integer.
We could in theory use %pa for this but then it would be in hex and also
that causes a warning about incorrect types anyway. Hence just
use the irq local variable we assigned the line above.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds a generic pressure driver for STMicroelectronics
pressure sensors, currently it supports: LPS331AP.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch introduce num_data_channels variable on st_sensors struct
to manage different type of channels (size or number) in
st_sensors_get_buffer_element function.
Removed ST_SENSORS_NUMBER_DATA_CHANNELS and ST_SENSORS_BYTE_FOR_CHANNEL
and used struct iio_chan_spec const *ch to catch data.
Added 3 byte channel data support on one-shot reads.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is now a very simple trigger indeed but useful in many common cases.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The data structure is required only when DT is enabled.
Hence compile it conditionally.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The code uses
return foo;
goto err_type;
when instead the form should have been
ret = foo;
goto err_type;
Here this causes a useful iio_device_put to be skipped.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The original driver was pasted from accelerometer driver, but the name
of the ID was not changed. This patch fixes this comment.
Signed-off-by: Alexandre Relange <alexandre@relange.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Drivers for STMicroelectronics accelerometers, gyroscopes, and
magnetometers were added in v3.9. They all have a (similar) select
statement in their Kconfig files for a non-existant Kconfig symbol.
These select statements can safely be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Implement "data ready" interrupt handling in addition to the
two existing read modes - DRDY GPIO polling and ST1 register
DRDY bit polling.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for parsing 'gpios' property when initializing
from oftree.
This patch adds also the binding documentation file.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This simple driver is rather useful. No issues about its interface
have been raised for some time hence the proposal to move it out
of staging.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
1. make messages grepable (in one line)
2. include returned errno in them
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for Microchip's 12 bit AD converters MCP3204 and
MCP3208. These chips communicates over SPI and supports single-ended
and pseudo-differential configurations.
Signed-off-by: Oskar Andero <oskar.andero@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The exynos_adc device structure was wrongly extracted from the dev*
correcting the same.
Using the regular conversion of
struct device* -> struct platform_device* -> struct exynos_adc* seems wrong.
Instead we should be doing
struct device* -> struct iio_dev* -> struct exynos_adc*
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch fixes below build error when CONFIG_SPI_MASTER=y && CONFIG_I2C=m:
drivers/built-in.o: In function `ad5064_i2c_write':
drivers/iio/dac/ad5064.c:608: undefined reference to `i2c_master_send'
drivers/built-in.o: In function `ad5064_i2c_register_driver':
drivers/iio/dac/ad5064.c:646: undefined reference to `i2c_register_driver'
drivers/built-in.o: In function `ad5064_i2c_unregister_driver':
drivers/iio/dac/ad5064.c:651: undefined reference to `i2c_del_driver'
make: *** [vmlinux] Error 1
When CONFIG_I2C=m, meaning we can't build the drivers in with I2C support.
Thus don't allow the drivers to be compiled as built-in when CONFIG_I2C=m.
The real fix though is to break the driver apart into a SPI part, an I2C part
and a common part. But that's something for 3.11 while this is something for
3.10/stable.
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
On the at91_adc a minimal Sample and Hold Time is necessary for the ADC to
guarantee the best converted final value between two channels selection.
This time has to be programmed through the bitfield SHTIM in the
Mode Register ADC_MR.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The sleep mode will allow to put the adc in sleep between conversion.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
at91 adc offers the choice between two resolutions: low and high.
The low and high resolution values depends on adc IP version, as many IP
properties have been exposed through device tree, these settings have also
been added to the dt bindings.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Issues raised in last series to propose this have now been resolved
so there should be no reason this driver cannot graduate from staging.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
exynos_adc is a DT only driver and exynos_adc_match table is always
compiled in. Hence remove the macro.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Introduce iio_tigger_{set,get}_drvdata which allows to attach driver specific
data to a trigger. The functions wrap access to the triggers private_data field
and all current users are updated to use iio_tigger_{set,get}_drvdata instead of
directly accessing the private_data field. This is the first step towards
removing the private_data field from the iio_trigger struct.
The following coccinelle script has been used to update the drivers:
<smpl>
@@
struct iio_trigger *trigger;
expression priv;
@@
-trigger->private_data = priv
+iio_trigger_set_drv_data(trigger, priv)
@@
struct iio_trigger *trigger;
@@
-trigger->private_data
+iio_trigger_get_drv_data(trigger)
</smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Without this change the exynos adc controller needed to have its phy
enabled in some out-of-driver C code. Add support for specifying the
phy enable register by listing it in the reg list.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ad7924 is software compatible with the ad7923. The ad7904 and ad7914 are the
8 and 10 bit version of the ad7924.
While we are at it also drop the "with temperature sensor" from the Kconfig
entry, since the chips do not have a temperature sensor.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Patrick Vasseur <patrick.vasseur@c-s.fr>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver already claims to support scale reporting in its channel spec, but
doesn't actually implement this yet. This patch uses the regulator API to get
the reference voltage and calculates the scale based on that. The patch also
moves the global configuration bits into a field in the ad7923_state struct,
since depending on the RANGE bit, the range goes either from 0 to VREF or from 0
to 2 * VREF. So we need to know the setting of the RANGE bit when calculating
the scale.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Patrick Vasseur <patrick.vasseur@c-s.fr>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Instead of leaving 'val' uninitialized return an error if the result's address
did not match that of the channel we were trying to read.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Patrick Vasseur <patrick.vasseur@c-s.fr>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
As the exynos_adc driver only supports device tree registration.
Making driver depend on CONFIG_OF solves possible errors during probe.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently it is not save to call iio_push_event() from hard IRQ context since
the IIO event code uses spin_lock()/spin_unlock() and it is not save to mix
calls to spin_lock()/spin_unlock() from different contexts on the same lock.
E.g. if the lock is being held in iio_event_chrdev_read() and an interrupts
kicks in and the interrupt handler calls iio_push_event() we end uo with a
deadlock.
This patch updates iio_push_event() to use spin_lock_irqsave()/
spin_unlock_irqstrestore(), since it can be called from both IRQ and non-IRQ
context. All other other users of the lock, which are always run in non-IRQ
context, are updated to spin_lock_irq()/spin_unlock_irq().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This has been replaced by the pair of masks info_mask_separate
and info_mask_shared_by_type. Other variants may follow.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
The original info_mask is going away in favour of the broken out versions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
cc: Patrick Vasseur <patrick.vasseur@c-s.fr>
cc: Christophe Leroy <christophe.leroy@c-s.fr>
Sebastian Andrzej Siewior