Add support for voltage, current, and temperature peak (historic maximum)
attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add support for voltage and temperature peak (historic maximum) attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add support for voltage and current peak (historic maximum) attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add the following attributes to the sysfs ABI.
in[0-*]_average
in[0-*]_lowest
in[0-*]_highest
in[0-*]_reset_history
in_reset_history
curr[1-*]_average
curr[1-*]_lowest
curr[1-*]_highest
curr[1-*]_reset_history
curr_reset_history
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add ADP4000, NCP4200 and NCP4208 to the list of devices supported by the generic
PMBus driver, and add device IDs to enable explicit instantiation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch adds the core and pkg support to coretemp.
These thresholds can be configured via the sysfs interfaces tempX_max
and tempX_max_hyst. An interrupt is generated when CPU temperature reaches
or crosses above tempX_max OR drops below tempX_max_hyst.
This patch is based on the documentation in IA Manual vol 3A, that can be
downloaded from here:
http://download.intel.com/design/processor/manuals/253668.pdf
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
A hwmon driver for the National Semiconductor LM95245 dual temperature
sensors chip.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for Philips SA56004, an LM86 compatible temperature sensor.
Signed-off-by: Stijn Devriendt <sdevrien@cisco.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for NTC Thermistor series. In this release, the
following thermistors are supported: NCP15WB473, NCP18WB473, NCP03WB473,
and NCP15WL333. This driver is based on the datasheet of MURATA.
The driver in the patch does conversion from the raw ADC value
(either voltage or resistence) to temperature. In order to use
voltage values as input, the circuit schematics should be provided
with the platform data. A compensation table for each type of thermistor
is provided for the conversion.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch adds support for MAX1668 and compatible temperature sensors.
Signed-off-by: David George <david.george@ska.ac.za>
[guenter.roeck@ericsson.com: minor cleanup of probe error path]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Declare myself the maintainer of the lm78 driver. I still have a
running system with one of these chips.
Also count myself as a co-author of the driver. With 34 commits over
6 years, it seems fair.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds a new driver for SMSC SCH5636 Super I/O chips.
The chips include an embedded microcontroller for hardware monitoring
solutions, allowing motherboard manufacturers to create their own
custom hwmon solution based upon the SCH5636.
Currently the sch5636 driver only supports the Fujitsu Theseus SCH5636
based hwmon solution. The sch5636 driver runs a sanity check on
loading to ensure it is dealing with a Fujitsu Theseus and not with
another custom SCH5636 based hwmon solution.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add some CPU series IDs and links to the Fam12h datasheets.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The F71869A is almost the same as the F71869F/E, except that it has
the normal number of temp and pwm zones for a F71882FG derived chip,
rather then the limited number of the F71869F/E.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Max Baldwin <archerseven@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is a new driver for the SMSC EMC6W201 hardware monitoring device.
The device is functionally close to the EMC6D100 series, but is
register-incompatible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Harry G McGavran Jr <w5pny@arrl.net>
Tested-by: Jeff Rickman <jrickman@myamigos.us>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The MAX6650 has only one fan input.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: "Hans J. Koch" <hjk@hansjkoch.de>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
MAX6650 device detection is unreliable, we got reports of false
positives. We now have many ways to let users instantiate the devices
explicitly, so unreliable detection should be dropped.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: "Hans J. Koch" <hjk@hansjkoch.de>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This CPU family provides NB register values to gather following
TDP information
* ProcessorPwrWatts: Specifies in Watts the maximum amount of power
the processor can support.
* CurrPwrWatts: Specifies in Watts the current amount of power being
consumed by the processor.
This driver provides
* power1_crit (ProcessorPwrWatts)
* power1_input (CurrPwrWatts)
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
AMDs upcoming CPUs use the same mechanism for the internal
temperature reporting as the Fam10h CPUs, so we just needed to add
the appropriate PCI-ID to the list.
This allows to use the k10temp driver on those CPUs.
While at it change the Kconfig entry to be more generic.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
After the merge of pkgtemp functionality into the coretemp driver,
the pkgtemp driver is no longer necessary. Remove it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch merges the pkgtemp with coretemp driver.
The sysfs interfaces for all cores in the same pkg
are shown under one directory, in hwmon. It also
supports CONFIG_HOTPLUG_CPU. So, the sysfs interfaces
are created when each core comes online and are
removed when it goes offline.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
[guenter.roeck@ericsson.com: Fixed section reference errors]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for Analog Devices ADM1275 Hot-Swap Controller and Digital Power
Monitor
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Hardware monitoring support for TI UCD90120, UCD90124, UCD9090, and UCD90910
Sequencer and System Health Controllers.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
This patch adds hardware monitoring support for TI UCD9220, UCD9222, UCD9224,
UCD9240, UCD9244, UCD9246, and UCD9248 Digital PWM System Controllers.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
This patch adds hardware monitoring support for Maxim MAX16065, MAX16066,
MAX16067, MAX16068, MAX16070, and MAX16071 flash-configurable system managers
with nonvolatile fault registers.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
The sht15 sensor allows validating exchanges to and from the device
using a crc8 function. An utility function to reverse a byte has also
been added.
Signed-off-by: Jerome Oufella <jerome.oufella@savoirfairelinux.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* Add support for:
- Heater.
- End of battery notice.
- Ability not to reload from OTP.
- Low resolution (12bit temp, 8bit humidity).
* Add an utility function to read individual bytes from the device.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* Add a documentation file for the device.
* Respect a bit more the kernel-doc syntax.
* Rename some variables for clarity.
* Use bool type for flags.
* Use an enum for states (actions being done).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
MAX6642 is a SMBus-Compatible Remote/Local Temperature Sensor with
Overtemperature Alarm from Maxim.
Signed-off-by: Per Dalen <per.dalen@appeartv.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Recent Xeon processor thermal sensors are supported by the coretemp
driver and not the adm1021 driver. Only one old generation of Xeon
processors (the first Netburst ones) are supported by the adm1021
driver.
Reported-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The lm90 driver's attribute update interval is configurable.
Reflect this information in the driver documentation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for ADT7461A and NCT1008 to the lm90 driver.
Both chips have identical functionality and report the same manufacturing ID
and device ID values.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
MAX34440 and MAX34441 have their own driver, thus there should be explicit
documentation instead of mentioning the chips in the generic PMBus driver
documentation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
MAX16064 has its own driver, thus should have its own documentation instead of
being mentioned in the generic PMBus driver documentation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
MAX8688 has its own driver, thus should have its own documentation instead of
being mentioned in the generic PMBus driver documentation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
tempererature may sound interesting, but temperature is still preferred.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
When writing hardware monitoring drivers, there are some common pitfalls which
keep coming up in code reviews. This patch provides a document describing all
those pitfalls and how to avoid them.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the Fintek F81865F. It's essentially compatible with
the F71882FG, but has fewer inputs: 7 voltage, 2 temperature and 2 fan
inputs only.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The list of supported devices was not always well documented in all
places. Clarify and list all devices in documentation, Kconfig and
the driver itself.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This driver exposes the sysfs nodes of the TWL4030 MADC module.
All the voltage channel values are expressed in terms of mV. Channel 13
and channel 14 are reserved. There are channels which represent
temperature and current the output is represented by celcius
and mA respectively.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Configuration for ads1015 gain and datarate is possible via
devicetree or platform data.
This is a followup patch to previous ads1015 patches on Jean Delvares
tree.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
SMSC SCH5627 Super I/O chips include complete hardware monitoring
capabilities. They can monitor up to 5 voltages, 4 fans and 8
temperatures.
The hardware monitoring part of the SMSC SCH5627 is accessed by talking
through an embedded microcontroller. An application note describing the
protocol for communicating with the microcontroller is available upon
request. Please mail me if you want a copy.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Guenter Roeck