The following change updates the Atlas interrupt handling to match that
of Malta. Tested with a 5Kc and a 34Kf successfully.
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
I've encountered a serious problem with PCI config space access on Au1x000
platforms with recent 2.6.x-kernel. With 2.4.31 the same hardware works fine.
So I was looking for the differences:
Symptoms:
- no PCI-device is seen on bootup though two or three cards are present
- lspci output is empty
- OR: lspci shows 20 times the same device
(- OR: in some slot-configurations it worked anyhow)
System(s):
1. platform with Au1500 and three PCI-devices (actually a mycable XXS1500
with backplane for three PCI-devices)
2. platform with Au1550 and two PCI-devices (custom board)
Debugging:
I digged down to the config_access() of the au1xxx-processors in
arch/mips/pci/ops-au1000.c and switched on DEBUG.
The code of config_access() seems to be almost the same as of the
2.4.x-kernel. But the "pci_cfg_vm->addr" returned by get_vm_area(0x2000, 0)
once on booting is different. That's of course not forbidden. But the
alignment seems to be wrong. In my case, I received:
2.4.31: pci_cfg_vm->addr = c0000000
2.6.18-rc5: pci_cfg_vm->addr = c0101000
To make it short: With 2.6.x it fails on the first config-access with:
"PCI ERR detected: status 83a00356".
Fixup:
My fix is now, to use the VM_IOREMAP-flag in the get_vm_area call. This flag
seems to be introduced in mm/vmalloc.c a long time ago (in 2.6.7-bk13, I
found in gitweb).
Now, the returned address is pci_cfg_vm->addr = c0104000 and everything works
fine.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for RM200C machines with big endian firmware
Added support for RM200-C40 (R5000 support)
Signed-off-by: Florian Lohoff <flo@rfc822.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Support for the GT-64120-based Wind River 4KC PPMC Evaluation board.
Signed-off-by: Rongkai.Zhan <Rongkai.zhan@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CFE 1.2.5 and earlier fails to turn on the ExpMemEn bit in the
PCIFeatureControl register, which means that DMA does not work
beyond physical address 01_0000_0000, ergo to DRAM beyond 1GB.
With ExpMemEn turned on, 01_0000_0000-0f_ffff_ffff is mapped,
so DMA works for up to 61 GB of DRAM.
Will be fixed in CFE 1.2.6 (yet to be released).
Signed-Off-By: Andy Isaacson <adi@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
PCI support code for PLX 7250 PCI-X tunnel on BCM91480B BigSur board.
Signed-Off-By: Andy Isaacson <adi@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
this fixes Lasat pci to work with multi-function devices by assigning
the correct values based on pin number (instead of ignoring them).
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Ralf Baechle