ahci_hardreset() and ahci_p5wdh_hardreset() use bare numbers for the
BSY bit of the ATA status register, despite it's #define'd in
<linux/ata.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 30dcf76acc "libata: migrate ACPI code over to new bindings"
mistakenly dropped the code to register hotplug notificaion handler
for ATA port/devices, causing regression for people using ATA bay,
as kernel bug #59871 shows.
Fix this by adding back the hotplug notification handler registration
code. Since this code has to be run once and notification needs to
be installed on every ATA port/devices handle no matter if there is
actual device attached, we can't do this in binding time for ATA
device ACPI handle, as the binding only occurs when a SCSI device is
created, i.e. there is device attached. So introduce the
ata_acpi_hotplug_init() function to loop scan all ATA ACPI handles
and if it is available, install the notificaion handler for it during
ATA init time.
With the ATA ACPI handle binding to SCSI device tree, it is possible
now that when the SCSI hotplug work removes the SCSI device, the ACPI
unbind function will find that the corresponding ACPI device has
already been deleted by dock driver, causing a scaring message like:
[ 128.263966] scsi 4:0:0:0: Oops, 'acpi_handle' corrupt
Fix this by waiting for SCSI hotplug task finish in our notificaion
handler, so that the removal of ACPI device done in ACPI unbind
function triggered by the removal of SCSI device is run earlier when
ACPI device is still available.
[rjw: Rebased]
References: https://bugzilla.kernel.org/show_bug.cgi?id=59871
Reported-bisected-and-tested-by: Dirk Griesbach <spamthis@freenet.de>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: 3.6+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are some SATA controllers which have both devices 0 and 1 but this module
just zeroes out taskfile and sets then ATA_TFLAG_DEVICE (not sure that's needed)
which could lead to a wrong device being selected just before issuing command.
Thus we should call ata_tf_init() which sets up the device register value
properly, like all other users of ata_exec_internal() do...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
This patch adds the AHCI-mode SATA DeviceIDs for the Intel Coleto Creek PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
This patch adds the IDE-mode SATA DeviceIDs for the Intel Coleto Creek PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
- Remove duplicate Medium Error Entry.
- Fix translations to match SAT2 translation table.
- Remove warning messages when translation is not found when decoding
error or status register.
- Goes through status register decoding when only ABRT bit is set in
error register.
Tested: When a disk fails, it sets
Status = 0x71 [DRDY DF ERR] , Error = 0x4 [ABRT]
This patch will make the sense key HARDWARE_ERROR instead.
When there is a simple command syntax error:
Status = 0x51 [DRDY ERR] , Error = 0x4 [ABRT]
The sense key remains ABORTED_COMMAND.
tj: Some updates to the description and comments.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds the compatible string of the exynos5440 sata controller
compliant with the ahci 1.3 and sata 3.0 specification.
changes in v2:
changed the compatible string by adding the actual IP
owners name instead of the SoC vendor name.
Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
For some reason, a lot of port-multipliers have issues with softreset.
SIMG [34]7x series port-multipliers have been quite erratic in this
regard. I recall that it was better with some firmware revisions and
the current list of quirks worked fine for a while. I think it got
worse with later firmwares or maybe my test coverage wasn't good
enough. Anyways, HPA is reporting that his 3726 setup suffers SRST
failures and then the PMP gets confused and fails to probe the last
port.
The hope was that we try to stick to the standard as much as possible
and soonish the PMPs and their firmwares will improve in quality, so
the quirk list was kept to minimum. Well, it seems like that's never
gonna happen.
Let's set NO_SRST for all [34]7x PMPs so that whatever remaining
userbase of the device suffer the least. Maybe we should do the same
for 57xx's but unfortunately I don't have any device left to test and
I'm not even sure 57xx's have ever been made widely available, so
let's leave those alone for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: stable@vger.kernel.org
ata_link_online() check in ahci_error_intr() is unnecessary, it should
be removed otherwise may lead to lockup with FBS enabled PMP.
http://marc.info/?l=linux-ide&m=137050421603272&w=2
Reported-by: Yu Liu <liuyu.ac@gmail.com>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Highbank supports SGPIO by bit-banging out the SGPIO signals over
three GPIO pins defined in the DTB. Add support for this SGPIO
functionality.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Create a new ata_port_operations function pointer called
transmit_led_message and give it the default value of
ahci_transmit_led_message. This allows AHCI controllers with
non-standard LED interfaces to use the existing em_ interface.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When compiling the driver with gcc 4.8, it gives the following warning:
drivers/ata/sata_rcar.c: In function `sata_rcar_thaw':
drivers/ata/sata_rcar.c:183:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
Fix the warning by explicit cast of the 'unsigned long' value to 'u32'.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Increase the retry count for the hard reset function to 100 but
shorten the time out period to 500 ms. See the comment for
ahci_highbank_hardreset for the reasons why those vaulues were
chosen.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0. If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.
Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.
To reduce overall code bloat, make the changes described above.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
To add AMD CZ SATA controller device ID of IDE mode.
[bhelgaas: drop pci_ids.h update]
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Use the wrapper function for getting the driver data using pci_dev
instead of using dev_get_drvdata() with &pdev->dev, so we can directly
pass a struct pci_dev. This is a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The driver's interrupt handling code is too picky in deciding whether it should
handle an interrupt or not which causes completely unneeded spurious interrupts.
Thus make sata_rcar_{ata|serr}_interrupt() *void*; add ATA status register read
to sata_rcar_ata_interrupt() to clear an unexpected ATA interrupt -- it doesn't
get cleared by writing to the SATAINTSTAT register in the interrupt mode we use.
Also, in sata_rcar_ata_interrupt() we should check SATAINTSTAT register only for
enabled interrupts and we should clear only those interrupts that we have read
as active first time around, because else we have a race and risk clearing an
interrupt that can occur between read and write of the SATAINTSTAT register
and never registering it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
A third possible PCI ID, as personally observed, and found in the
pci.ids list.
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The 'base' field of 'struct sata_rcar_priv' is used very often
throughout the driver, so it seems worth loading it into a local
variable if it's used more than once in a function.
While at it, put some unitialized variables after intialized ones for
aesthetic reasons. :-)
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Using ATA_BMDMA_SHT() to intialize 'sata_rcar_sht' was suboptimal as
the R-Car descriptor table transfer counter is 28 bits wide (bit 1 to
bit 28), so that the 'dma_boundary' field of 0xFFFF is just too small,
as well as the 'sg_tablesize' field of 128. Use ATA_BASE_SHT() to
initialize 'sata_rcar_sht' instead and give proper values to the
'dma_boundary' and 'sg_tablesize' fields explicitly.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
I've modified sata_rcar_bmdma_fill_sg() to take care of splitting long
scatter/ gather segments due to the descriptor table transfer counter
being only 28 bits wide (bit 1 to bit 28) but that was in vain as even
if 'sata_rcar_sht' specified a correct 'dma_boundary' field, the DMA
and block layers would have split the S/G segments on the necassary
boundaries. Since the driver uses ATA_BMDMA_SHT() to initilaize
'sata_rcar_sht', the boundary is much smaller, only 0xFFFF, so the
code I've added is even more useless, and it's better to just remove
it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The motivation for this is to allow the driver to be
used with the r8a7790 SoC.
I believe that rather than adding another SoC to the list of allowed SoCs
it is better to simply remove the dependency of the driver on shmobile all
together.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently all interrupts assigned to AHCI ports show up in
'/proc/interrupts' as 'ahci'. This fix adds port numbers as
suffixes and hence makes the descriptions distinct.
Reported-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Iff bmdma_setup() has to stop a DMA transfer before starting a new
one, then the STOP bit in the ATAPI_CONTROL1 register will remain set
(it's only cleared when setting the START bit to 1) and then
bmdma_start() method will set both START and STOP bits simultaneously
which should abort the transfer being just started. Avoid that by
explicitly clearing the STOP bit in bmdma_start() method (in this case
it will be ignored on write).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Some device require DMADIR to be enabled, but are not detected as such
by atapi_id_dmadir. One such example is "Asus Serillel 2"
SATA-host-to-PATA-device bridge: the bridge itself requires DMADIR,
even if the bridged device does not.
As atapi_dmadir module parameter can cause problems with some devices
(as per Tejun Heo's memory), enabling it globally may not be possible
depending on the hardware.
This patch adds atapi_dmadir in the form of a "force" horkage value,
allowing global, per-bus and per-device control.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
While registering host controller track port number based upon number
of ports available on the controller, export port_no attribute through
/sys. This patch is needed by udev for composing persistent links in
/dev/disk/by-path.
/sys/devices/pci0000:00/0000:00:1f.2/ata8/ata_port/ata8
total 0
lrwxrwxrwx. 1 root root 0 Mar 6 12:43 device -> ../../../ata8
-r--r--r--. 1 root root 4096 Mar 6 12:43 idle_irq
-r--r--r--. 1 root root 4096 Mar 6 12:43 nr_pmp_links
-r--r--r--. 1 root root 4096 Mar 6 12:43 port_no
drwxr-xr-x. 2 root root 0 Mar 6 12:42 power
lrwxrwxrwx. 1 root root 0 Mar 6 12:41 subsystem -> ../../../../../../class/ata_port
-rw-r--r--. 1 root root 4096 Mar 6 12:40 uevent
1
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Jeff moved on to a greener pasture.
s/Maintained by: Jeff Garzik/Maintained by: Tejun Heo/g
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
mkinitrd looks at /sys/class/scsi_host/host$hostnum/proc_name to find
the module name of a disk driver. Current name is "highbank-ahci" but
the module is "sata_highbank". Rename it to match the module name.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: <stable@vger.kernel.org> v3.7..
Signed-off-by: Robert Richter <robert.richter@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch restores libata.noacpi support to libata-acpi.c.
There are broken optional control methods for ATA controller devices in the
real world. The libata.noacpi has been used for a long time as a
workaround to deal with issues caused by the broken ASL codes.
1. The "noacpi" option is introduced by the following commit:
commit 11ef697b37
Date: Thu, 28 Sep 2006 11:29:01 -0700
Subject: libata: ACPI and _GTF support
2. The "noacpi" option is renamed to "libata_noacpi" by the following
commit:
commit d7d0dad62a
Date: Wed, 28 Mar 2007 01:57:37 -0400
Subject: [libata] Disable ACPI by default; fix namespace problems
3. Some of its logics are changed over time - becomes relying on the
"acpi_handle" bound to the ATA devices since this commit:
commit fafbae87db
Date: Tue, 15 May 2007 03:28:16 +0900
Subject: libata-acpi: implement ata_acpi_associate()
4. The option is deleted by the following commit:
commit 30dcf76acc
Date: Mon, 25 Jun 2012 16:13:04 +0800
Subject: libata: migrate ACPI code over to new bindings
But the libata.noacpi setup is still left in the kernel without codes to
implement it. So the deletion introduces a regression to the Linux.
This patch disables ATA_ACPI support at runtime by stopping acpi binding
on the ATA devices to fix this regression.
This patch is tested by booting a SATA x86-64 kernel or a PATA x86 kernel
with or without "libata.noacpi=1" kernel command line argument.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since commit 30dcf76acc, ata_ap_acpi_handle will always do a namespace
walk, which requires acquiring an acpi namespace mutex. This made it
impossible to be used when calling path has held a spinlock.
For example, it can occur in the following code path for pata_acpi:
ata_scsi_queuecmd (ap->lock is acquired)
__ata_scsi_queuecmd
ata_scsi_translate
ata_qc_issue
pacpi_qc_issue
ata_acpi_stm
ata_ap_acpi_handle
acpi_get_child
acpi_walk_namespace
acpi_ut_acquire_mutex (acquire mutex while holding lock)
This caused scheduling while atomic bug, as reported in bug #56781.
Actually, ata_ap_acpi_handle doesn't have to walk the namespace every
time it is called, it can simply return the bound acpi handle on the
corresponding SCSI host. The reason previously it is not done this way
is, ata_ap_acpi_handle is used in the binding function
ata_acpi_bind_host by ata_acpi_gtm when the handle is not bound to the
SCSI host yet. Since we already have the ATA port's handle in its
binding function, we can simply use it instead of calling
ata_ap_acpi_handle there. So introduce a new function __ata_acpi_gtm,
where it will receive an acpi handle param in addition to the ATA port
which is solely used for debug statement. With this change, we can make
ata_ap_acpi_handle simply return the bound handle for SCSI host instead
of walking the acpi namespace now.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=56781
Reported-and-tested-by: <kenzopl@o2.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This adds a complete DT binding for the arasan device driver. There is
currently only one user, which is the spear13xx platform, so we don't
actually have to parse all the properties until another user comes in,
but this does use the generic DMA binding to find the DMA channel.
The patch is untested so far and is part of a series to convert
the spear platform over to use the generic DMA binding, so it
should stay with the rest of the series.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.linux@linaro.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Cc: devicetree-discuss@lists.ozlabs.org
With the 0x1b4b vendor ID #define in place, convert hard-coded ID
values.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Fix the follwing warnings:
linux/drivers/ata/pata_pdc2027x.c:66: warning: 'pdc2027x_reinit_one' declared 'static' but never defined
pdc2027x_reinit_one are defined only when CONFIG_PM is defined,
thus making it conditional.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As per c78968bb by Jeff Garzik ([libata] SCSI: simulator version, not device
version, belongs in VPD) We need to provide the SATL driver version and not the
disk firmware version but the code overwrites the driver version with the disk
version.
Signed-off-by: Baruch Even <baruch@ev-en.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Not much to do here, only the compatible entries have to be added.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
regs is returned from ioremap, so add a __iomem. Also, make it
void * instead of u8 *.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- rename free_priv label to 'err' since priv is allocated with devm_*
and not freed here.
- add missing 'goto err' in case ata_host_activate fails
- add 'ret' variable to return correct error value instead of hardcoded
-ENOMEM in error case.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Support config RX WATER MARK via sysfs when running at run-time;
A wrokaround for fix the exception happened to some WD HDD, found on
WD3000HLFS-01G6U1, WD3000HLFS-01G6U0, some SSD disks. The read performance
is also regression (about 30%) when use default value.
According to the latest documents, 0x10 is the default value of RX WATER MARK,
but exception/performance issue happened to some disks mentioned above.
The exception log as below when testing read performance with IOZone:
ata1.00: exception Emask 0x0 SAct 0x7 SErr 0x800000 action 0x6 frozen
ata1: SError: { LinkSeq }
ata1.00: failed command: READ FPDMA QUEUED
ata1.00: cmd 60/00:00:ff:2c:14/01:00:02:00:00/40 tag 0 ncq 131072 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1.00: failed command: READ FPDMA QUEUED
ata1.00: cmd 60/00:08:ff:2d:14/01:00:02:00:00/40 tag 1 ncq 131072 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1.00: failed command: WRITE FPDMA QUEUED
ata1.00: cmd 61/10:10:af:08:6e/00:00:12:00:00/40 tag 2 ncq 8192 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: hard resetting link
ata1: Hardreset failed, not off-lined 0
ata1: Signature Update detected @ 504 msecs
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: configured for UDMA/133
ata1.00: device reported invalid CHS sector 0
ata1.00: device reported invalid CHS sector 0
ata1.00: device reported invalid CHS sector 0
ata1: EH complete
The exception/performance can be resolved when RX WATER MARK value is 0x16.
Signed-off-by: Qiang Liu <qiang.liu@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With commit:
bc9b6407bd
ACPI / PM: Rework the handling of devices depending on power resources
The ACPI core now takes care of the power resources an acpi device
depends on in that when the power resources are turned on, any devices
that are bound to or in the dependent list of this acpi device will be
runtime resumed. So there is no need for ata acpi code to duplicate this
effort, and thus, the ata_acpi_(un)register_power_resource functions are
no longer needed.
The above commit thinks the scsi device is not bound to the acpi device,
so needs to be added to the dependent list. But actually, it is. So
there is no need to add it to the dependent list, or it will be runtime
resumed twice(though this wouldn't cause any problem).
This patch fixes it, and as a result, the
ata_acpi_(un)register_power_resource and ata_acpi_(un)bind functions
are removed.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make ahci_highbank_pm_ops static because ahci_highbank_pm_ops is
not exported.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use resource_size function instead of explicit computation.
Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
"sysclk" is used as an index into a 4 element array. My static
checker complains because it can be out of bounds. From the
context, it looks like there is a right bit shift missing.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Sergei Shtylyov