Convert iscsi_tcp to new lib functions.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Reduce duplication in the software iscsi_transport modules by
adding a libiscsi function to handle the common grunt work.
This also has the drivers return specifc -EXXX values for different
errors so userspace can finally handle them in a sane way.
Also just pass the sysfs buffers to the drivers so HW iscsi can
get/set its string values, like targetname, and initiatorname.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from david.somayajulu@qlogic.com:
Add target discovery event. We may have a setup where the iscsi traffic
is on a different netowrk than the other network traffic. In this case
we will want to do discovery though the iscsi card. This patch adds
a event to the transport class that can be used by hw iscsi cards that
support this.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I noticed that in_use in st_buffer is not used. The patch below
against 2.6.17-rc3 removes it, assuming there is no future use for it.
It was tested in a sparc SS20 with a DLT4000.
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The atp870u driver is the largest stack eater reported by checkstack
(on x86_864, allmodconfig). This converts the offending function
to kmalloc+kfree struct atp_unit instead of allocating it on the stack.
Was:
0x0000164c atp870u_probe [atp870u]: 3176
Now:
0x0000164c atp870u_probe [atp870u]: 408
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
this patch introduces a port object, separates out ports and phys,
with ports becoming the primary objects of the tree.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If a device gets offlined as a result of the Inquiry sent
during scanning, the following oops can occur. After the
disk gets put into the SDEV_OFFLINE state, the error handler
sends back the failed inquiry, which wakes the thread doing
the scan. This starts a race between the scanning thread
freeing the scsi device and the error handler calling
scsi_run_host_queues to restart the host. Since the disk
is in the SDEV_OFFLINE state, scsi_device_get will still
work, which results in __scsi_iterate_devices getting
a reference to the scsi disk when it shouldn't.
The following execution thread causes the oops:
CPU 0 (scan) CPU 1 (eh)
---------------------------------------------------------
scsi_probe_and_add_lun
....
scsi_eh_offline_sdevs
scsi_eh_flush_done_q
scsi_destroy_sdev
scsi_device_dev_release
scsi_restart_operations
scsi_run_host_queues
__scsi_iterate_devices
get_device
scsi_device_dev_release_usercontext
scsi_run_queue
<---OOPS--->
The patch fixes this by changing the state of the sdev to SDEV_DEL
before doing the final put_device, which should prevent the race
from occurring.
Original oops follows:
Badness in kref_get at lib/kref.c:32
Call Trace:
[C00000002F4476D0] [C00000000000EE20] .show_stack+0x68/0x1b0 (unreliable)
[C00000002F447770] [C00000000037515C] .program_check_exception+0x1cc/0x5a8
[C00000002F447840] [C00000000000446C] program_check_common+0xec/0x100
Exception: 700 at .kref_get+0x10/0x28
LR = .kobject_get+0x20/0x3c
[C00000002F447B30] [C00000002F447BC0] 0xc00000002f447bc0 (unreliable)
[C00000002F447BB0] [C000000000254BDC] .get_device+0x20/0x3c
[C00000002F447C30] [D000000000063188] .scsi_device_get+0x34/0xdc [scsi_mod]
[C00000002F447CC0] [D0000000000633EC] .__scsi_iterate_devices+0x50/0xbc [scsi_mod]
[C00000002F447D60] [D00000000006A910] .scsi_run_host_queues+0x34/0x5c [scsi_mod]
[C00000002F447DF0] [D000000000069054] .scsi_error_handler+0xdb4/0xe44 [scsi_mod]
[C00000002F447EE0] [C00000000007B4E0] .kthread+0x128/0x178
[C00000002F447F90] [C000000000025E84] .kernel_thread+0x4c/0x68
Unable to handle kernel paging request for <7>PCI: Enabling device: (0002:41:01.1), cmd 143
data at address 0x000001b8
Faulting instruction address: 0xd0000000000698e4
sym1: <1010-66> rev 0x1 at pci 0002:41:01.1 irq 216
sym1: No NVRAM, ID 7, Fast-80, LVD, parity checking
sym1: SCSI BUS has been reset.
scsi2 : sym-2.2.2
cpu 0x0: Vector: 300 (Data Access) at [c00000002f447a30]
pc: d0000000000698e4: .scsi_run_queue+0x2c/0x218 [scsi_mod]
lr: d00000000006a904: .scsi_run_host_queues+0x28/0x5c [scsi_mod]
sp: c00000002f447cb0
msr: 9000000000009032
dar: 1b8
dsisr: 40000000
current = 0xc0000000045fecd0
paca = 0xc00000000048ee80
pid = 1123, comm = scsi_eh_1
enter ? for help
[c00000002f447d60] d00000000006a904 .scsi_run_host_queues+0x28/0x5c [scsi_mod]
[c00000002f447df0] d000000000069054 .scsi_error_handler+0xdb4/0xe44 [scsi_mod]
[c00000002f447ee0] c00000000007b4e0 .kthread+0x128/0x178
[c00000002f447f90] c000000000025e84 .kernel_thread+0x4c/0x68
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a resend of a patch I generated in response to an email sent
by Ruben Faelens <parasietje@gmail.com>. His original email to
linux-scsi requested a method in which he could spin down a scsi disk
when not in use and have the kernel automatically spin it back up when
an I/O was generated to the disk. The infrastructure to automatically
spin a disk up has been in the scsi error handler for some time now,
but it is not enabled by default. This patch adds an sd sysfs attribute
which allows userspace to enable this behavior.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
locking init cleanups:
- convert " = SPIN_LOCK_UNLOCKED" to spin_lock_init() or DEFINE_SPINLOCK()
- convert rwlocks in a similar manner
this patch was generated automatically.
Motivation:
- cleanliness
- lockdep needs control of lock initialization, which the open-coded
variants do not give
- it's also useful for -rt and for lock debugging in general
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Original post was incorrect as it didn't realize that we already had
a self-referenc due to device_initialize(), and we were really only
missing the put on our own reference. This was hidden by the other bug
which had the midlayer reusing stargets after they were already free,
which was doing too many puts on our rport.
Updating FC transport for:
- Add put in fc_rport_final_delete(), to release the rport.
Prior, we were leaving the rport with a reference, thus the shost
with references, etc. If the driver was unloaded, shosts and rports
remained, along with work threads, etc
- Fix fc_rport_create failure path - too many put's on parent
- Add commenting to easily track ref taking.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Updated patch to address comments from Pat Mansfield and Michael Reed:
Bumped max to 600 (10mins). Set default dev_loss_tmo to a value other
than the max (30s).
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In a prior posting to linux-scsi on the fc transport and workq
deadlocks, we noted a second error that did not have a patch:
http://marc.theaimsgroup.com/?l=linux-scsi&m=114467847711383&w=2
- There's a deadlock where scsi_remove_target() has to sit behind
scsi_scan_target() due to contention over the scan_lock().
Subsequently we posted a request for comments about the deadlock:
http://marc.theaimsgroup.com/?l=linux-scsi&m=114469358829500&w=2
This posting resolves the second error. Here's what we now understand,
and are implementing:
If the lldd deletes the rport while a scan is active, the sdev's queue
is blocked which stops the issuing of commands associated with the scan.
At this point, the scan stalls, and does so with the shost->scan_mutex held.
If, at this point, if any scan or delete request is made on the host, it
will stall waiting for the scan_mutex.
For the FC transport, we queue all delete work to a single workq.
So, things worked fine when competing with the scan, as long as the
target blocking the scan was the same target at the top of our delete
workq, as the delete workq routine always unblocked just prior to
requesting the delete. Unfortunately, if the top of our delete workq
was for a different target, we deadlock. Additionally, if the target
blocking scan returned, we were unblocking it in the scan workq routine,
which really won't execute until the existing stalled scan workq
completes (e.g. we're re-scheduling it while it is in the midst of its
execution).
This patch moves the unblock out of the workq routines and moves it to
the context that is scheduling the work. This ensures that at some point,
we will unblock the target that is blocking scan. Please note, however,
that the deadlock condition may still occur while it waits for the
transport to timeout an unblock on a target. Worst case, this is bounded
by the transport dev_loss_tmo (default: 30 seconds).
Finally, Michael Reed deserves the credit for the bulk of this patch,
analysis, and it's testing. Thank you for your help.
Note: The request for comments statements about the gross-ness of the
scan_mutex still stand.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This removes the duplicate functionality which had been added to
the lpfc driver.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The scsi midlayer portion of the patch
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Ata_piix's Kconfig entry still refers only to ICH5, while it supports ICH6
through 8. This creates confusion with people who are looking to see
if their newer SATA enabled motherboards are supported. The
following patch makes this clear.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some SATA controllers embedded in ATI IXPs seem to have broken
SATA_IRQ bit in their bmdma2 registers which is always stuck at 1.
This makes the driver believe that there has been a hotplug event and
freeze the port whenever there's an interrupt thus failing all
commands.
This patch disables SATA_IRQ for those controllers.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cosmetic updates in libata-core.c.
* trim trailing whitespaces
* break lines which are over 80 column
* kill unnecessary braces
* make indentation consistent
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Andrew Morton <akpm@osdl.org>
Provide a module parameter to override the default 30-second-per-device SATA
probing timeout.
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_do_simple_cmd() and ata_flush_cache() global. These will be
used from libata-eh.c.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* the function has always returned AC_ERR_* masks not -errno but its
return type was int. Make return type unsigned int.
* don't print error message automatically. it's the caller's
responsibility.
* add header comment
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clear related EH action on device detach such that new device doesn't
receive EH actions scheduled for the old one.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement and use ata_eh_dev_action() which returns EH action mask for
a device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Partially revert 74d0a988d3aa359b6b8a8536c8cb92cce02ca5d5:
[PATCH] PCI: Move various PCI IDs to header file
libata policy is to avoid use of named PCI device ID constants.
These are often single-use constants, which have little value over
direct numeric constants save for constant include/linux/pci_ids.h
patching/merging headaches.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This may seem like a DILLIGAF, but after chatting with the F/W folks,
there is no harm in dropping the page calculation as denoted in the
enclosed patch for these older adapters in this new age of 4GB+ memory
sticks. Any resource optimization within the old-old-old adapters for
systems with less than 4G of memory is of little consequence. The
existing AAC_QUIRK_31BIT flag in linit.c should look after the rest of
the legacy hardware DMA limitations.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The scsi layer is already calling add_disk_randomness in scsi_end_request.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We currently stuff a truncated size into the geometry logic and return the
result which can produce bizarre reports for a 4Tb array. Since that
mapping logic isn't useful for disks that big don't try and map this way at
all.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Randy Dunlap <rdunlap@xenotime.net>
Fix sparse warnings: use NULL instead of 0 for pointers:
drivers/scsi/lpfc/lpfc_els.c:827:56: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_els.c:2781:18: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_els.c:2782:18: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_init.c:951:21: warning: Using plain integer as NULL pointer
drivers/scsi/lpfc/lpfc_init.c:956:20: warning: Using plain integer as NULL pointer
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original code incorrectly assigned it to the driver's
link-down-timeout value (a value in seconds).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Also remove qla2xxx_probe_one/qla2xxx_remove_one stubs previously
used with external firmware module loaders.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As there is no point in failing the initialization process when
firmware informs the host software that it could not transition
beyond a CONFIG_WAIT nor WAIT_FOR_LOGIN state. Previous logic
would mark such conditions as a general *failure* and subsequently
tear-down the scsi-host during initialization.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Similar in form to QLogic's standard offering -- via
the 'extended_error_logging' module parameter.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- macro usage statements should terminate with a ';'
- remove unused macros.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The host section of ISP24xx NVRAMs contain a new bit which
allows a user to selectively disable ports of an HBA. These
ports (hosts) will not be presented to the midlayer.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Defer firmware dump-data raw-to-textual conversion to
user-space.
- Add module parameter (ql2xallocfwdump) to allow for per-HBA
allocations of firmware dump memory.
- Dump request and response queue data as per firmware group
request.
- Add extended firmware trace support for ISP24XX/ISP54XX chips.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Rename the GART_IOMMU option to IOMMU to make clear it's not
just for AMD
- Rewrite the help text to better emphatise this fact
- Make it an embedded option because too many people get it wrong.
To my astonishment I discovered the aacraid driver tests this
symbol directly. This looks quite broken to me - it's an internal
implementation detail of the PCI DMA API. Can the maintainer
please clarify what this test was intended to do?
Cc: linux-scsi@vger.kernel.org
Cc: alan@redhat.com
Cc: markh@osdl.org
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts the combination of list_del(A) and list_add(A, B) to
list_move(A, B) under drivers/.
Acked-by: Corey Minyard <minyard@mvista.com>
Cc: Ben Collins <bcollins@debian.org>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Alasdair Kergon <dm-devel@redhat.com>
Cc: Gerd Knorr <kraxel@bytesex.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frank Pavlic <fpavlic@de.ibm.com>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Cc: Andrew Vasquez <linux-driver@qlogic.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mike Christie