Some HP laptops have lower amplifier levels for speakers in comparison
with headphone outputs. This patch changes the BTL amp level for these
machines to balance both the speaker and headphone output levels.
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The sticky PCM stream assignment introduced in 2.6.36 kernel seems
causing problems on AD codecs. At some time later, the streaming no
longer works by unknown reason. A simple workaround is to disable
sticky-assignment for these codecs.
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is to allow a future patch to have card specific mappings between
dacs, which is required since the Sound Blaster 5.1vx seems to have a
different mapping to what was previously used.
Signed-off-by: Andy Owen <andy-alsa@ultra-premium.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is ground work for a future commit where cards (such as the Sound
Blaster 5.1vx) have different mappings between dacs and channels.
Signed-off-by: Andy Owen <andy-alsa@ultra-premium.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Creative IBG controllers require the playback stream-tags to be started
from 1, instead of capture+1. Otherwise the stream stalls.
Reported-by: Wai Yew CHAY <wychay@ctl.creative.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The bit value set for TLV mute was wrong in commit
de8c85f784, which resulted in bogus
dB ranges that screw up PulseAudio. Corrected with the right constant.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Multiple Acer laptops with the SSID 1025:04xx require the quirk
mode=ideapad, so let's use mask to apply to all these.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Creative HD-audio controller chips require some workarounds:
- Additional delay before RIRB response
- Set the initial RIRB counter to 0xc0
The latter seems to be done in general in Windows driver, so we may
use this value later for all types if it's confirmed to work better.
Reported-by: Wai Yew CHAY <wychay@ctl.creative.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The dig_out_nid field must take a digital-converter widget, but the current
ca0110 parser passed the pin wrongly instead.
Reported-by: Wai Yew CHAY <wychay@ctl.creative.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Windows may leave pin power-down registers set after reboot, and
this resulted in muted output on Linux. Reset these registers
at initialization properly.
Signed-off-by: Charles Chin <Charles.Chin@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The HDA specification does not allow for a codec to mute itself just
because the volume is reduced, so _of course_ somebody had to go and do
it. This wouldn'\''t hurt too much when the volume is adjusted by hand,
but programs like PA that try to set the volume automatically could
inadvertently mute the output.
To work around this, change the TLV dB information for the Master volume
on all Sigmatel HDA codecs to indicate the the minimal volume setting
actually mutes.
Reported-by: Colin Guthrie <gmane@colin.guthr.ie>
Reported-by: "Alexander E. Patrakov" <patrakov@gmail.com>
Tested-by: Colin Guthrie <cguthrie@mandriva.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: http://launchpad.net/bugs/617647
The current SKU value disables playback, so ignore the SKU value.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Realtek have ways of specifying external amps and more via a
special nid or via the Codec's subsystem ID, this is called "SKU".
The computer manufacturer sometimes gets this wrong, so we need
to be able to override or ignore the SKU customization value.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://bugs.launchpad.net/bugs/653420
Add another HP DV6 notebook (103c:363e) to use STAC_HP_DV5.
Signed-off-by: Luke Yelavich <luke.yelavich@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This board has a strange PCI SSID 13f6:ffff. Works as compabile as
MODEL_CMEDIA_REF.
Reported-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Configure the PEX8111 bridge on the PCI Express cards so that the audio
DMA controller can do proper burst reads and is less likely to lose
data. This is usually done automatically, but is required on older
cards where the user has not applied the PLX firmware update.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the PCIe/PCI bridge initialization code to configure only the
bridge that is actually connected to the sound chip, instead of any
bridge found in the system. The new code also makes it easier to add
other bridges.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The interrupt counter is independent of the buffer counter, so there are
no restrictions on the period size. Having fewer periods also makes
PulseAudio happy.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The input monitor half volume bit results in a factor of 0.5, so the
minimum scale value should be -6 dB.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rename the symbol for the XCID pins, fix up a decimal/hex confusion for
the CMI8787 package ID, and add the other known package IDs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The anti-pop delay for the STX should be 800 ms, not 100 ms like the ST.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a PCI ID for the Xonar HDAV1.3 Slim. There is no actual support,
but the presence of the ID allows the EEPROM repair code to work for
this card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are more models without a CD input than with one, so handle this
explicitly with a device_config flag to avoid having to define a control
filter callback to filter it out.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The controller on the Xonar DS is labeled "AV66", not "AV200".
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
What was previously known as via_dmapos_patch, and hard-coded to be
used for VIA and ATI controllers, is now configurable through a module
option. The background is that some VIA controllers seem to prefer
via_dmapos_patch to be turned off.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The SNDRV_HDSP_IOCTL_GET_CONFIG_INFO and
SNDRV_HDSP_IOCTL_GET_CONFIG_INFO ioctls in hdspm.c and hdsp.c allow
unprivileged users to read uninitialized kernel stack memory, because
several fields of the hdsp{m}_config_info structs declared on the stack
are not altered or zeroed before being copied back to the user. This
patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix bug in switching between dmic and mic when both use the same mux.
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The SPDIF in audio widget must be searched through the list as the widget
that contains the given pin as the connection source. The current code
was implemented in a reverse way.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I've found the following patch is necessary to enable line-in on
my MacBookPro 5,3 machine. With the patch applied I've successfully
recorded audio from the line-in jack. This is based on the existing
5,5 support.
Signed-off-by: Vince Weaver <vweaver1@eecs.utk.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the HT-Omega Claro halo card, the ADC data must be captured from the
second I2S input. Using the default first input, which isn't connected
to anything, would result in silence.
Signed-off-by: Erik J. Staab <ejs@insightbb.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've applied a fix-up for ALC269 VAIO only for two models. But all
Sony VAIO models with ALC269 codec seem to require the similar fix.
Let's apply it with vendor-id mask.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The headphone and external-mic pin NIDs can be null, and the jack input
elements should be skipped in such a case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the explicit ifdef check and call of check_power_status ops with
a new helper function, hda_call_check_power_status().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vitaliy Kulikov