max_nrg_cck value inside the sensitivity range structure is not needed
for sensitivity calibration.
Keep the parameter in sensitivity structure but set the value to "0" in case
needed in the future implementation.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In 5150 there is a long delay between the AGC(Automatic Gain Control) command
till the RF is stabilized causing us to miss detections when there was
adjacent channel noise, so we need to adjusted the Sensitivity calibration
for 5150 differently.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unifies 3945 and AGN station management
It also removes useless struct iwl_station_mgmt ops
and cleanups a bit the interface
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ICT interrupt handler support, ICT should improve CPU utilization
since it does not require target read which is very expensive. This
interrupt handler only added to 5000 cards and newer. Device will write
interrupts to ICT shared table to inform driver about its interrupts.
These patches will not touch 3945 and 4965 interrupt handlers and tasklet.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new lock to be used when accessing some registers. Also move
the register lock and iwl_grab_nic_access inside the function for register access. This
will prevent from forgetting to hold locks and nic access in the right way and make code
easier to maintain.
We over use the priv->lock spin lock and I guess we need to add new
one for Tx queue after that we might need to change most of these lock to
BH and just keep priv->lock as irq type.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The temperature measurement by uCode for 5150 and 5000 are different
CSR_HW_REV_TYPE_5150: temperature sensor output voltage
CSR_HW_REV_TYPE_5000: temperature in Celsius
temperature related operation for 5150 is measured by temperature sensor
output voltage; additional conversion is required for set and store
the temperature.
To make sure support different HW design; implement _ops method for
temperature related functions (temperature reading and set ct kill
threshold)
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
enable iwl driver to support 5000 ucode having version 2 of API
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch removes the "manual radio disable" parameter
as there is no usage scenario of disabling radio using this module parameter.
User can use iwconfig's txpower to enable and disable radio.
This module parameter also does not work as expected. During module load
the status of radio is set, the radio is not actually disabled. Even so,
the moment mac80211 requests the interface to be up the radio will be
enabled again.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add config_ap lib op to iwlwifi and iwl3945 in preparation
of future 3945 porting actions.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add set_rxon_chain op to iwlwifi cfg ops in preparation of
future 3945 porting work.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch unifies the add_station function for 3945 and iwlwifi drivers.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds declarations for station management ops to iwlwifi drivers.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can use iwl_bss_info_changed.
A new lib op is created for post_assoicate to distinguish between
3945 and iwlwifi's post_associate operations.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes all the virtual A-MPDU-queue bookkeeping from
mac80211. Curiously, iwlwifi already does its own bookkeeping, so
it doesn't require much changes except where it needs to handle
starting and stopping the queues in mac80211.
To handle the queue stop/wake properly, we rewrite the software
queue number for aggregation frames and internally to iwlwifi keep
track of the queues that map into the same AC queue, and only talk
to mac80211 about the AC queue. The implementation requires calling
two new functions, iwl_stop_queue and iwl_wake_queue instead of the
mac80211 counterparts.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Reinette Chattre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fix related to bug 1921 at
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1921
when detect error during stopping tx aggregation queue, report the error to
help identify the problem.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
update API to support new numbering that is used for other newer devices.
5150 ucode has not been released yet, so the first released API will be v2.
For those who do have a v1 API the driver does have backward compatibility
support new value of REPLY_TX_POWER_DBM_CMD
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces where possible usage of pci register
defined in the driver by ones defined in pci_regs.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
defined the structures and functions as extern to alter behavior used by
5000 series for other products including 100 and 6000 series
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct the API commands where same command id used for two different
commands. Update max api versions for affected devices.
TX_ANT_CONFIGURATION_CMD was already using id 0x98, so
REPLY_TX_POWER_DBM_CMD moved to 0x95
Older API interfaces may used original value so V1 defines provided.
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
added a config parameter to enable setting PLL_CFG. older hardware has
this parameter set true. the 6000 family does not support this setting,
so this parameter set false.
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
by parametrizing the set hw function, in addition to allowing for
supporting the 6000 family significantly simplify the addition of new
hardware.
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Call IWL_DEBUG macro with explicit priv argument.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By adding an additional hw_params (tfd_size) and a new iwl_lib ops (txq_init),
we can now use the iwlcore TX queue management routines.
We had to add a new hw_params because we need to allocate the right DMA buffer
for TFDs, and those have a different sizes depending if you're on 3945 or agn.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
remove static from config structures which will be used by new
hardware that is similar to 5000. This way the new devices
can use them without the new structures having to be stored in the
already overloaded iwl-5000.c file.
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TFD structures for 3945 and agn HWs are fundamentally different. We thus
need to define operations for attaching and freeing them. This will allow us
to share a fair amount of code (cmd and tx queue related) between both
drivers.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch kills iwl3945_rx_queue_restock function on prise of new
hw_params.rx_wrt_ptr_reg which holds per NIC RX write pointer register.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IWL_ERR doesn't use hidden priv pointer.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IWL_WARN doesn't use hidden priv pointer.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SRAM addresses are different for 3945, 4065, and 5000, let's give them
different names.
Also, the RSSI_OFFSET is different for 3945 and 4965, thus they should be
named differently.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch removes some useless goto in code cleanup.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables one to change the debug level at bit 31.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ability of disabling qos from module params is not required anymore.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch merges implementation of iwl_poll_bit() and
iwl_poll_direct_bit() by letting the latter be a special case of
the former.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the infrastructure to support older firmware APIs.
The API version number is stored as part of the filename, we first try to
load the most recent firmware and progressively try lower versions.
The API version is also read from the firmware self and stored as part
of the iwl_priv structure. Only firmware that is supported by driver will
be loaded. The version number read from firmware is compared
to supported versions in the driver not the API version used as part of
filename.
An example using this new infrastrucure:
if (IWL_UCODE_API(priv->ucode_ver) >= 2) {
Driver interacts with Firmware API version >= 2.
} else {
Driver interacts with Firmware API version 1.
}
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes the misuse of DMA channel number by Tx queue number in
iwl_tx_ctx_stop().
The problem was originally reported by Wu Fengguang who complains
iwlagn driver takes too long time when issuing `ifconfig wlan0 down`.
The patch now decreases the interface bring down time from 2 seconds
to 0.8 second.
This fixes bugs:
http://bugzilla.kernel.org/show_bug.cgi?id=11956http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1790
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables LO, TXIQ, and BB calibrations for 5150
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for 5150 eeprom versions
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds computation of ct kill threshold
for 5150. Threshold is computed from calibration
data in the EEPROM.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables DC calibration for 5150
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This instructs FH to increment the retry count of a packet when
it is brought from the memory to TX-FIFO to save transactions
during aggregation flow.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch configures correctly TX DMA channel. It is not
the same as TX queue.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds base band calibration support.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves code around and group most of the station
management code into iwl-sta.c
No functional changes (yet)
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves byte count tables to tx domain removing completely
ambivalent shared data. Changes handling of allocation
byte count tables and keep warm consistent memory
Moves general tx scheduler definitions from iwl-4956-hw.h
to iwl-fh.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy