arch/powerpc/platforms/pseries/hotplug-memory.c uses
remove_section_mapping() but doesn't include sparsemem.h which defines
it. This can cause compilation fails for some configs.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Convert arch/powerpc/ over to long long based u64:
-#ifdef __powerpc64__
-# include <asm-generic/int-l64.h>
-#else
-# include <asm-generic/int-ll64.h>
-#endif
+#include <asm-generic/int-ll64.h>
This will avoid reoccuring spurious warnings in core kernel code that
comes when people test on their own hardware. (i.e. x86 in ~98% of the
cases) This is what x86 uses and it generally helps keep 64-bit code
32-bit clean too.
[Adjusted to not impact user mode (from paulus) - sfr]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, pseries_cpu_die() calls msleep() while polling RTAS for
the status of the dying cpu.
However, if the cpu that is going down also happens to be the one
doing the tick then we're hosed as the tick_do_timer_cpu 'baton' is
only passed later on in tick_shutdown() when _cpu_down() does the
CPU_DEAD notification. Therefore jiffies won't be updated anymore.
This replaces that msleep() with a cpu_relax() to make sure we're not
going to schedule at that point.
With this patch my test box survives a 100k iterations hotplug stress
test on _all_ cpus, whereas without it, it quickly dies after ~50
iterations.
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Cc: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When running Active Memory Sharing, pages can get marked as
"loaned" with the hypervisor by the CMM driver. This state gets
cleared by the system firmware when rebooting the partition.
When using kexec to boot a new kernel, this state never gets
cleared and the hypervisor and CMM driver can get out of sync
with respect to the number of pages currently marked "loaned".
Fix this by adding a reboot notifier to the CMM driver to deflate
the balloon and mark all pages as active.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When running Active Memory Sharing, the Collaborative Memory Manager
(CMM) may mark some pages as "loaned" with the hypervisor.
Periodically, the CMM will query the hypervisor for a loan request,
which is a single signed value. When kexec'ing into a kdump kernel,
the CMM driver in the kdump kernel is not aware of the pages the
previous kernel had marked as "loaned", so the hypervisor and the CMM
driver are out of sync. This results in the CMM driver getting a
negative loan request, which can then get treated as a large unsigned
value and can cause kdump to hang due to the CMM driver inflating too
large. Since there really is no clean way for the CMM driver in the
kdump kernel to clean this up, simply disable CMM in the kdump kernel.
This fixes hangs we were seeing doing kdump with AMS.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ibm_configure_kernel_dump is passed as the token to rtas_call() is
never initialised. This sets it to something sane.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Manish Ahuja <mahujam@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
print_dump_header() will be called at least once with a NULL pointer in
a normal boot sequence. If DEBUG is defined then we will dereference
the pointer and crash. Add a quick fix to exit early in the NULL pointer
case.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Manish Ahuja <mahujam@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes a long-standing performance bug in classic RCU that
results in massive internal-to-RCU lock contention on systems with
more than a few hundred CPUs. Although this patch creates a separate
flavor of RCU for ease of review and patch maintenance, it is intended
to replace classic RCU.
This patch still handles stress better than does mainline, so I am still
calling it ready for inclusion. This patch is against the -tip tree.
Nevertheless, experience on an actual 1000+ CPU machine would still be
most welcome.
Most of the changes noted below were found while creating an rcutiny
(which should permit ejecting the current rcuclassic) and while doing
detailed line-by-line documentation.
Updates from v9 (http://lkml.org/lkml/2008/12/2/334):
o Fixes from remainder of line-by-line code walkthrough,
including comment spelling, initialization, undesirable
narrowing due to type conversion, removing redundant memory
barriers, removing redundant local-variable initialization,
and removing redundant local variables.
I do not believe that any of these fixes address the CPU-hotplug
issues that Andi Kleen was seeing, but please do give it a whirl
in case the machine is smarter than I am.
A writeup from the walkthrough may be found at the following
URL, in case you are suffering from terminal insomnia or
masochism:
http://www.kernel.org/pub/linux/kernel/people/paulmck/tmp/rcutree-walkthrough.2008.12.16a.pdf
o Made rcutree tracing use seq_file, as suggested some time
ago by Lai Jiangshan.
o Added a .csv variant of the rcudata debugfs trace file, to allow
people having thousands of CPUs to drop the data into
a spreadsheet. Tested with oocalc and gnumeric. Updated
documentation to suit.
Updates from v8 (http://lkml.org/lkml/2008/11/15/139):
o Fix a theoretical race between grace-period initialization and
force_quiescent_state() that could occur if more than three
jiffies were required to carry out the grace-period
initialization. Which it might, if you had enough CPUs.
o Apply Ingo's printk-standardization patch.
o Substitute local variables for repeated accesses to global
variables.
o Fix comment misspellings and redundant (but harmless) increments
of ->n_rcu_pending (this latter after having explicitly added it).
o Apply checkpatch fixes.
Updates from v7 (http://lkml.org/lkml/2008/10/10/291):
o Fixed a number of problems noted by Gautham Shenoy, including
the cpu-stall-detection bug that he was having difficulty
convincing me was real. ;-)
o Changed cpu-stall detection to wait for ten seconds rather than
three in order to reduce false positive, as suggested by Ingo
Molnar.
o Produced a design document (http://lwn.net/Articles/305782/).
The act of writing this document uncovered a number of both
theoretical and "here and now" bugs as noted below.
o Fix dynticks_nesting accounting confusion, simplify WARN_ON()
condition, fix kerneldoc comments, and add memory barriers
in dynticks interface functions.
o Add more data to tracing.
o Remove unused "rcu_barrier" field from rcu_data structure.
o Count calls to rcu_pending() from scheduling-clock interrupt
to use as a surrogate timebase should jiffies stop counting.
o Fix a theoretical race between force_quiescent_state() and
grace-period initialization. Yes, initialization does have to
go on for some jiffies for this race to occur, but given enough
CPUs...
Updates from v6 (http://lkml.org/lkml/2008/9/23/448):
o Fix a number of checkpatch.pl complaints.
o Apply review comments from Ingo Molnar and Lai Jiangshan
on the stall-detection code.
o Fix several bugs in !CONFIG_SMP builds.
o Fix a misspelled config-parameter name so that RCU now announces
at boot time if stall detection is configured.
o Run tests on numerous combinations of configurations parameters,
which after the fixes above, now build and run correctly.
Updates from v5 (http://lkml.org/lkml/2008/9/15/92, bad subject line):
o Fix a compiler error in the !CONFIG_FANOUT_EXACT case (blew a
changeset some time ago, and finally got around to retesting
this option).
o Fix some tracing bugs in rcupreempt that caused incorrect
totals to be printed.
o I now test with a more brutal random-selection online/offline
script (attached). Probably more brutal than it needs to be
on the people reading it as well, but so it goes.
o A number of optimizations and usability improvements:
o Make rcu_pending() ignore the grace-period timeout when
there is no grace period in progress.
o Make force_quiescent_state() avoid going for a global
lock in the case where there is no grace period in
progress.
o Rearrange struct fields to improve struct layout.
o Make call_rcu() initiate a grace period if RCU was
idle, rather than waiting for the next scheduling
clock interrupt.
o Invoke rcu_irq_enter() and rcu_irq_exit() only when
idle, as suggested by Andi Kleen. I still don't
completely trust this change, and might back it out.
o Make CONFIG_RCU_TRACE be the single config variable
manipulated for all forms of RCU, instead of the prior
confusion.
o Document tracing files and formats for both rcupreempt
and rcutree.
Updates from v4 for those missing v5 given its bad subject line:
o Separated dynticks interface so that NMIs and irqs call separate
functions, greatly simplifying it. In particular, this code
no longer requires a proof of correctness. ;-)
o Separated dynticks state out into its own per-CPU structure,
avoiding the duplicated accounting.
o The case where a dynticks-idle CPU runs an irq handler that
invokes call_rcu() is now correctly handled, forcing that CPU
out of dynticks-idle mode.
o Review comments have been applied (thank you all!!!).
For but one example, fixed the dynticks-ordering issue that
Manfred pointed out, saving me much debugging. ;-)
o Adjusted rcuclassic and rcupreempt to handle dynticks changes.
Attached is an updated patch to Classic RCU that applies a hierarchy,
greatly reducing the contention on the top-level lock for large machines.
This passes 10-hour concurrent rcutorture and online-offline testing on
128-CPU ppc64 without dynticks enabled, and exposes some timekeeping
bugs in presence of dynticks (exciting working on a system where
"sleep 1" hangs until interrupted...), which were fixed in the
2.6.27 kernel. It is getting more reliable than mainline by some
measures, so the next version will be against -tip for inclusion.
See also Manfred Spraul's recent patches (or his earlier work from
2004 at http://marc.info/?l=linux-kernel&m=108546384711797&w=2).
We will converge onto a common patch in the fullness of time, but are
currently exploring different regions of the design space. That said,
I have already gratefully stolen quite a few of Manfred's ideas.
This patch provides CONFIG_RCU_FANOUT, which controls the bushiness
of the RCU hierarchy. Defaults to 32 on 32-bit machines and 64 on
64-bit machines. If CONFIG_NR_CPUS is less than CONFIG_RCU_FANOUT,
there is no hierarchy. By default, the RCU initialization code will
adjust CONFIG_RCU_FANOUT to balance the hierarchy, so strongly NUMA
architectures may choose to set CONFIG_RCU_FANOUT_EXACT to disable
this balancing, allowing the hierarchy to be exactly aligned to the
underlying hardware. Up to two levels of hierarchy are permitted
(in addition to the root node), allowing up to 16,384 CPUs on 32-bit
systems and up to 262,144 CPUs on 64-bit systems. I just know that I
am going to regret saying this, but this seems more than sufficient
for the foreseeable future. (Some architectures might wish to set
CONFIG_RCU_FANOUT=4, which would limit such architectures to 64 CPUs.
If this becomes a real problem, additional levels can be added, but I
doubt that it will make a significant difference on real hardware.)
In the common case, a given CPU will manipulate its private rcu_data
structure and the rcu_node structure that it shares with its immediate
neighbors. This can reduce both lock and memory contention by multiple
orders of magnitude, which should eliminate the need for the strange
manipulations that are reported to be required when running Linux on
very large systems.
Some shortcomings:
o More bugs will probably surface as a result of an ongoing
line-by-line code inspection.
Patches will be provided as required.
o There are probably hangs, rcutorture failures, &c. Seems
quite stable on a 128-CPU machine, but that is kind of small
compared to 4096 CPUs. However, seems to do better than
mainline.
Patches will be provided as required.
o The memory footprint of this version is several KB larger
than rcuclassic.
A separate UP-only rcutiny patch will be provided, which will
reduce the memory footprint significantly, even compared
to the old rcuclassic. One such patch passes light testing,
and has a memory footprint smaller even than rcuclassic.
Initial reaction from various embedded guys was "it is not
worth it", so am putting it aside.
Credits:
o Manfred Spraul for ideas, review comments, and bugs spotted,
as well as some good friendly competition. ;-)
o Josh Triplett, Ingo Molnar, Peter Zijlstra, Mathieu Desnoyers,
Lai Jiangshan, Andi Kleen, Andy Whitcroft, and Andrew Morton
for reviews and comments.
o Thomas Gleixner for much-needed help with some timer issues
(see patches below).
o Jon M. Tollefson, Tim Pepper, Andrew Theurer, Jose R. Santos,
Andy Whitcroft, Darrick Wong, Nishanth Aravamudan, Anton
Blanchard, Dave Kleikamp, and Nathan Lynch for keeping machines
alive despite my heavy abuse^Wtesting.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since "Factor out cpu joining/unjoining the GIQ"
(b4963255ad) the WARN_ON in
xics_set_cpu_giq() is being triggered during boot on JS20 because the
GIQ indicator is not available on that platform. While the warning is
harmless and the system runs normally, it's nicer to check for the
existence of the indicator before trying to manipulate it.
Implement rtas_indicator_present(), which searches the
/rtas/rtas-indicators property for the given indicator token, and use
this function in xics_set_cpu_giq().
Also use a WARN statement in xics_set_cpu_giq to get better
information on failure.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Impact: change existing irq_chip API
Not much point with gentle transition here: the struct irq_chip's
setaffinity method signature needs to change.
Fortunately, not widely used code, but hits a few architectures.
Note: In irq_select_affinity() I save a temporary in by mangling
irq_desc[irq].affinity directly. Ingo, does this break anything?
(Folded in fix from KOSAKI Motohiro)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Ingo Molnar <mingo@redhat.com>
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: jeremy@xensource.com
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Impact: change calling convention of existing cpumask APIs
Most cpumask functions started with cpus_: these have been replaced by
cpumask_ ones which take struct cpumask pointers as expected.
These four functions don't have good replacement names; fortunately
they're rarely used, so we just change them over.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: paulus@samba.org
Cc: mingo@redhat.com
Cc: tony.luck@intel.com
Cc: ralf@linux-mips.org
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: cl@linux-foundation.org
Cc: srostedt@redhat.com
The pseries PCI hotplug code has a number of issues, ranging from
incorrect resource setup to crashes, depending on what is added,
when, whether it contains a bridge, etc etc....
This fixes a whole bunch of these, while actually simplifying the code
a bit, using more generic code in the process and factoring out common
code between adding of a PHB, a slot or a device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To properly fix PCI hotplug, it's useful to be able to make the fixup
passes on all devices whether they were just hot plugged or already
there.
The EEH code however used to not be very friendly with calling
eeh_add_device_late() multiple time, and not very rebust in the way it
generally tests whether a device is in the expected state vs. the EEH
code.
This improves it, along with cleaning up a couple of debug printk's.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 'ibm,interrupt-server#-size' properties are not in the cpu nodes,
which is where we currently look for them, but rather live under the
interrupt source controller nodes (which have "ibm,ppc-xics" in their
compatible property).
This moves the code that looks for the ibm,interrupt-server#-size
properties from xics_update_irq_servers() into xics_init_IRQ().
Also this adds a check for mismatched sizes across the interrupt
source controller nodes. Not sure this is necessary as in this case
the firmware might be seriously busted.
This property only appears on POWER6 boxes and is only used in the
set-indicator(gqirm) call, and apparently firmware currently ignores
the value we pass. Nevertheless we need to fix it in case future
firmware versions use it.
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This gets rid of this build warning:
arch/powerpc/platforms/pseries/pci_dlpar.c: In function 'init_phb_dynamic':
arch/powerpc/platforms/pseries/pci_dlpar.c:192: warning: unused variable 'b'
This is one of the very few warnings left in a ppc64_defconfig build and
getting rid of it will make it easier to see future introduced ones (in
fact this was introduced very recently).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Resources for PHB's that are dynamically added to a system are not
properly allocated in the resource tree.
Not having these resources allocated causes an oops when removing
the PHB when we try to release them.
The diff appears a bit messy, this is mainly due to moving everything
one tab to the left in the pcibios_allocate_bus_resources routine.
The functionality change in this routine is only that the
list_for_each_entry() loop is pulled out and moved to the necessary
calling routine.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
linux/crash_dump.h defines is_kdump_kernel() to be used by code that
needs to know if the previous kernel crashed instead of a (clean) boot
or reboot.
This updates the just added powerpc code to use it. This is needed
for the next commit, which will remove __kdump_flag.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds relocatable kernel support for kdump. With this one can
use the same regular kernel to capture the kdump. A signature (0xfeed1234)
is passed in r6 from panic code to the next kernel through kexec_sequence
and purgatory code. The signature is used to differentiate between
kdump kernel and non-kdump kernels.
The purgatory code compares the signature and sets the __kdump_flag in
head_64.S. During the boot up, kernel code checks __kdump_flag and if it
is set, the kernel will behave as relocatable kdump kernel. This kernel
will boot at the address where it was loaded by kexec-tools ie. at the
address reserved through crashkernel boot parameter.
CONFIG_CRASH_DUMP depends on CONFIG_RELOCATABLE option to build kdump
kernel as relocatable. So the same kernel can be used as production and
kdump kernel.
This patch incorporates the changes suggested by Paul Mackerras to avoid
GOT use and to avoid two copies of the code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Mohan Kumar M <mohan@in.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We used to assume that even numbered threads were the primary
threads, ie those that would be listed and started as a cpu from
open firmware. Replace a left over is even (% 2) check with a check
for it being a primary thread and update the comments.
Tested with a debug print on pseries, identical code found for cell.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The pfn of the memory to be removed should be validated prior to
attempting to remove the memory. In cases where the probe of a
memory section fails during hotplug add, the pfn for the lmb may
not be valid.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A single full sync (mb()) is requrired to order the mmio to the qirr reg
with the set or clear of the message word. However, test_and_clear_bit
has the effect of smp_mb() and we are not doing any other io from here,
so we don't need a mb per bit processed.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Several printks were broken at word boundaries for line length. Some
even referred to old function names. Using __func__ and changing the
text slightly for the format allows these printk formats to fit on one
line.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It is physically per-cpu, and we want the irq layer to treat it that way.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
EOI normally has the side effect of returning the cpu to the base
priority to recieve the next interrupt. This is actually controlled
by the top byte of the xirr register. When we are exiting the
kernel in kexec we must eoi the ipi for the next kernel because we
never return from the handler, but we want to leave interrupt
delivery blocked until the next kernel takes action.
Since the hardware ipi vector is fixed, its easiest to just do the
eoi explicitly.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This factors out processors joining and unjoining the Global Interrupt
Queue into a separate function.
There is a bit of math to calculate the arguments to rtas to join
or leave the global interrupt queue, and a warning on failure
afterwards. Make a helper for the 3 callers.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We only need to check the ibm,interrupt-server#-size property once, not
once per global server and thread.
We can use !CONFIG_SMP cpu masks and hard_smp_processor_id() to avoid an ifdef.
Put the node when breaking out of the loop on lpar systems.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Trim unneeded includes from xics.c. We don't use signals or gfp
flags, we use only OF functions and don't need prom, and the 8259
is now handled by our caller.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The xirr is 32 bits in hardware, but the hypervisor requries the upper
bits of the register to be clear on the hcall. By changing the type
from signed to unsigned int we can drop masking it back to 32 bits.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that xics_update_irq_servers is called only from init and hotplug
code, it becomes possible to clean up the ordering of functions in the
file, grouping them but the interfaces they implement.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
xics supports only one ipi per cpu, and expects software to use some
queue to know why the interrupt was sent. In Linux, we use a an array
of bitmaps indexed by cpu to identify the message. Currently the bits
are set in smp.c and decoded in xics.c, with the data structure in a
header file. Consolidate the code in xics.c similar to mpic and other
interrupt controllers.
Also, while making the the array static, the message word doesn't need
to be volatile as set_bit and test_clear_bit take care of it for us, and
put it under ifdef smp.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, every time we determine which irq server to use, we check if
default_server, which is the id of the bootcpu, is still online. But
default_server is a hardware cpu, not the logical cpu id needed to index
cpu_online_map.
Since the default server can only go offline during a cpu hotplug event,
explicitly check the default server and choose the new one when we move
irqs away from the cpu being offlined.
This has the added benefit of only needing the boot_cpuid to be updated
and not relying on the cpu being marked offline during migrate_irqs_away.
Also, since xics_update_irq_servers only reads device tree information, we
can call it before xics_init_host in xics_init_IRQ and then default_server
will always be valid when we can reach get_irq_server via the host ops.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When reciving an irq vector that does not have a linux mapping, the kernel
prints a message and calls RTAS to disable the irq source. Previously
the kernel did not EOI the interrupt, causing the source to think it is
still being processed by software. While this does add an additional
layer of protection against interrupt storms had RTAS failed to disable
the source, it also prevents the interrupt from working when a driver
later enables it. (We could alternatively send an EOI on startup, but
that strategy would likely fail on an emulated xics.)
All interrupts should be disabled when the kernel starts, but this can
be observed if a driver does not shutdown an interrupt in its reboot
hook before starting a new kernel with kexec.
Michael reports this can be reproduced trivially by banging the keyboard
while kexec'ing on a P5 LPAR: even though the hvc_console driver request's
the console irq later in boot, the console is non-functional because
we're receiving no console interrupts.
Reported-By: Michael Ellerman
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Testing hotplug memory remove has revealed that we can oops in
pseries_lmb_remove(). The incorrect shift causes a NULL pointer
dereference in the page_zone() inline routine.
I have only been able to reproduce the oops on kernels with large pages
enabled.
Tested on Power5 and Power6 with and without large pages enabled.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
rtas_log_read() doesn't check file flags for O_NONBLOCK and blocks
non-blocking readers of /proc/ppc64/rtas/error_log when there is
no data available. This fixes it.
Also rtas_log_read() returns now with ENODATA to prevent suspending of
process in wait_event_interruptible() when logging facility was
switched off and log is already empty.
Signed-off-by: Vitaly Mayatskikh <v.mayatskih@gmail.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
irq_radix_revmap() currently serves 2 purposes, irq mapping lookup
and insertion which happen in interrupt and process context respectively.
Separate the function into its 2 components, one for lookup only and one
for insertion only.
Fix the only user of the revmap tree (XICS) to use the new functions.
Also, move the insertion into the radix tree of those irqs that were
requested before it was initialized at said tree initialization.
Mutual exclusion between the tree initialization and readers/writers is
handled via a state variable (revmap_trees_allocated) set to 1 when the tree
has been initialized and set to 2 after the already requested irqs have been
inserted in the tree by the init path. This state is checked before any reader
or writer access just like we used to check for tree.gfp_mask != 0 before.
Finally, now that we're not any longer inserting nodes into the radix-tree
in interrupt context, turn the GFP_ATOMIC allocations into GFP_KERNEL ones.
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The return code from invocation of the notifier for
pSeries_reconfig_chain during update of the device tree is not
checked. This causes writes to /proc/ppc64/ofdt to update memory
properties (i.e. ibm,dyamic-reconfiguration-memory) to always
return success, instead of the result of the notifier chain.
This happens specifically when we remove/add memory from the
device tree on machines using memory specified in the
ibm,dynamic-reconfiguration-memory property of the device tree.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch also includes the required removal of (unused) inclusion of
<asm/a.out.h> <linux/a.out.h>'s in the arch/ code for these
architectures.
[dwmw2: updated for 2.6.27-rc]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fixes an error building powerpc allmodconfig:
ERROR: "CMO_PageSize" [arch/powerpc/platforms/pseries/cmm.ko] undefined!
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently print_device_node_tree() isn't called but it can be useful for
debugging. Leave the function there but hide it behind '#if 0' to save
it being rewritten. If you want to call it you're already editing this
file anyway. ;P
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
__FUNCTION__ is gcc-specific, use __func__
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the firmware page size used for collaborative memory overcommit
is 4k, but the kernel is using 64k pages, the page loaning is currently
broken as it only marks the first 4k page of each 64k page as loaned.
This fixes this to iterate through each 4k page and mark them all as
loaned/active.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
During platform setup, save off the primary/secondary paging space
pool IDs and the page size. Added accessors in hvcall.h for these
variables. This is needed for a subsequent fix.
Submitted-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Noticed due to these wanings:
arch/powerpc/platforms/pseries/cmm.c:298: warning: initialization from incompatible pointer type
arch/powerpc/platforms/pseries/cmm.c:299: warning: initialization from incompatible pointer type
arch/powerpc/platforms/pseries/cmm.c:320: warning: initialization from incompatible pointer type
arch/powerpc/platforms/pseries/cmm.c:320: warning: initialization from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To support Cooperative Memory Overcommitment (CMO), we need to check
for failure from some of the tce hcalls.
These changes for the pseries platform affect the powerpc architecture;
patches for the other affected platforms are included in this patch.
pSeries platform IOMMU code changes:
* platform TCE functions must handle H_NOT_ENOUGH_RESOURCES errors and
return an error.
Architecture IOMMU code changes:
* Calls to ppc_md.tce_build need to check return values and return
DMA_MAPPING_ERROR for transient errors.
Architecture changes:
* struct machdep_calls for tce_build*_pSeriesLP functions need to change
to indicate failure.
* all other platforms will need updates to iommu functions to match the new
calling semantics; they will return 0 on success. The other platforms
default configs have been built, but no further testing was performed.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adds a collaborative memory manager, which acts as a simple balloon driver
for System p machines that support cooperative memory overcommitment
(CMO).
Adds a platform configuration option for CMO called PPC_SMLPAR.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Newer versions of firmware support page states, which are used by the
collaborative memory manager (future patch) to "loan" pages to the
hypervisor for use by other partitions.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For Cooperative Memory Overcommitment (CMO), set the FW_FEATURE_CMO
flag in powerpc_firmware_features from the rtas ibm,get-system-parameters
table prior to calling iommu_init_early_pSeries.
With this, any CMO specific functionality can be controlled by checking:
firmware_has_feature(FW_FEATURE_CMO)
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch changes the EEH_MAX_FAILS action from panic to printing an
error message. Panicking under under this condition is too harsh.
Although performance will be affected and the device may not recover,
the system is still running, which at the very least should allow for a
more graceful shutdown. The patch also removes the msleep() within a
spinlock, which can lead to a deadlock and is not recommended.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update iommu_alloc() to take the struct dma_attrs and pass them on to
tce_build(). This change propagates down to the tce_build functions of
all the platforms.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling