In addition to the periodic heartbeat, we're adding a heartbeat
request interrupt when the heartbeat is late. This is needed during
netpoll where the timer is not available. -rt kernels will also
benefit since the timer is not as accurate.
[ We discussed this patch last time and we decided that the -rt
kernel problem alone did not justify this patch. I think the
netpoll problem makes this patch necessary. ]
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spurious interrupts are often encountered especially on systems
using the 8259 PIC mode. This is because the I/O write to deassert
the interrupt is posted and won't get to the chip immediately. As
a result, the IRQ may remain asserted after the IRQ handler exits,
causing spurious interrupts.
Add read back to flush the I/O write to deassert the IRQ immediately.
We also store the last_status_idx immediately in the IRQ handler to
help detect whether the interrupt is ours or not when the IRQ is
entered again before ->poll gets called.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the link up dmesg to report remote copper or Serdes link.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the driver's ethtool_ops->get_settings and set_settings
functions to support remote PHY. Users control the remote copper
PHY settings by specifying link settings for the tp (twisted pair)
port.
The nway_reset function is also modified to support remote PHY.
mii-tool operations are not supported on remote PHY and we will
return -EOPNOTSUPP.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In blade servers, the Serdes PHY in 5708S can control the remote
copper PHY through autonegotiation on the backplane. This patch adds
the logic to interface with the firmware to control the remote PHY
autonegotiation and to handle remote PHY link events.
When remote PHY is present, the 5708S Serdes device practically
becomes a copper device with full control over the 1000Base-T
link settings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new fields in struct bnx2 and other bit definitions in shared
memory to support remote PHY.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put existing code to setup the default link settings in this new
function. This makes it easier to support the remote PHY feature in
the next few patches.
Also change ETHTOOL_ALL_FIBRE_SPEED to include 2500Mbps if supported.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new syscall TUNSETGROUP for group ownership setting of tap
devices. The user now is allowed to send packages if either his euid or
his egid matches the one specified via tunctl (via -u or -g
respecitvely). If both, gid and uid, are set via tunctl, both have to
match.
Signed-off-by: Guido Guenther <agx@sigxcpu.org>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the multiqueue hardware device support API to the core network
stack. Allow drivers to allocate multiple queues and manage them at
the netdev level if they choose to do so.
Added a new field to sk_buff, namely queue_mapping, for drivers to
know which tx_ring to select based on OS classification of the flow.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver handles only L2TP data frames; control frames are handled
by a userspace application. It implements L2TP using the PPPoX socket
family. There is a PPPoX socket for each L2TP session in an L2TP
tunnel. PPP data within each session is passed through the kernel's
PPP subsystem via this driver. Kernel parameters of each socket can be
read or modified using ioctl() or [gs]etsockopt() calls.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing model for checksum offload does not correctly handle
devices that can offload IPV4 and IPV6 only. The NETIF_F_HW_CSUM flag
implies device can do any arbitrary protocol.
This patch:
* adds NETIF_F_IPV6_CSUM for those devices
* fixes bnx2 and tg3 devices that need it
* add NETIF_F_IPV6_CSUM to ipv6 output (incl GSO)
* fixes assumptions about NETIF_F_ALL_CSUM in nat
* adjusts bridge union of checksumming computation
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a list instead of an array to allow creating new devices.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a list instead of an array to allow creating new devices.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It hasn't "summed" anything in over 7 years, and it's
just a straight mempcy ala skb_copy_to_linear_data()
so just get rid of it.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Chad Tindel <ctindel@users.sourceforge.net>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
This is the third submission of the network driver for PS3.
The differences from the previous one are:
- renamed source file names so that their prefix can match
with the module name
- added cbe-oss-dev@ozlabs.org line for MAINTAINER file
- changed some in copyright comments
If there are no more comments, please apply for 2.6.23.
Thank you
--
Subject: PS3: Ethernet driver
From: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Add Gigabit Ethernet support for the PS3 game console. The module will
be called ps3_gelic.
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch introduces a capability flag that is used by the DLPAR userspace
tool to check which DLPAR features are supported by the eHEA driver.
Missing goto has been included.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
At present, when a device is enslaved to bonding, if ipv6 is
active then addrconf will be initated on the slave (because it is closed
then opened during the enslavement processing). This causes DAD and RS
packets to be sent from the slave. These packets in turn can confuse
switches that perform ipv6 snooping, causing them to incorrectly update
their forwarding tables (if, e.g., the slave being added is an inactve
backup that won't be used right away) and direct traffic away from the
active slave to a backup slave (where the incoming packets will be
dropped).
This patch alters the behavior so that addrconf will only run on
the master device itself. I believe this is logically correct, as it
prevents slaves from having an IPv6 identity independent from the
master. This is consistent with the IPv4 behavior for bonding.
This is accomplished by (a) having bonding set IFF_SLAVE sooner
in the enslavement processing than currently occurs (before open, not
after), and (b) having ipv6 addrconf ignore UP and CHANGE events on
slave devices.
The eql driver also uses the IFF_SLAVE flag. I inspected eql,
and I believe this change is reasonable for its usage of IFF_SLAVE, but
I did not test it.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
usbnet_probe() handles a positive return value from the driver bind()
function as success, but will later only setup the status handler if the
return value was zero, leading to confusion. Patch adjusts this to accept
positive values as success in both checks.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Get rid of dubious casts to (void *) which causes a sparse warning.
And move largeish function from inline to the one file that uses the code,
the compiler can then decide to inline it.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add 88E1112 PHY ID to the marvell driver. Seems to do fine with the
88E1111 inits.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simplify the marvell driver init a bit: Make the supported devices an
array instead of explicitly registering each structure. This makes it
considerably easier to add new devices down the road.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Support for the Asix AX88796 network controller, an
NE2000 compatible 10/100 ethernet device with internal
PHY.
The driver supports PHY settings via either ioctl() or
the ethtool driver ops.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
TX49XX SoCs include PCI NIC (TC35815 compatible) connected via its
internal PCI bus, but the NIC's PROM interface is not connected to
SEEPROM. So we must provide its ethernet address by another way.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the IOC3 driver to use ref counting pci interfaces so that we can
obsolete the (usually unsafe) pci_find_{slot/device} interfaces and avoid
future authors writing hotplug-unsafe device drivers.
Signed-off-by: Alan Cox <alan@redhat.com>
Build fixes:
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 82550 & 51 parts have an extended configuration block that
includes a bit "GMRC", required to enable the expected TCO behavior,
in config byte offset 22d. The config block sent by the failing driver
does include the extension area, but this bit is not initialised,
and the downlaod only specifies 0x16 bytes to be sent to the NIC
(thaht's bytes 00..21d). By initializing the GMRC bit, and extending
the download size for D102+ MACs, the problem is resolved.
Signed-off-by: David Graham <david.graham@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The QE Ethernet driver was writing to the wrong register to mask interrupts.
In ucc_geth_stop(), it was clearing UCCE instead of UCCM.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We intend this patch to improve spidernet interrupt handling to be
more strict. We had following problem and this patch solves it.
-when CONFIG_DEBUG_SHIRQ=y, request_irq() calls handler().
-when spider_net_open() is called, it calls request_irq() which calls
spider_net_interrupt().
-if some specific interrupt bit is set at this timing, it calls
netif_rx_schedule() and spider_net_poll() is scheduled.
-spider_net_open() calls netif_poll_enable() which clears the bit
__LINK_STATE_RX_SCHED.
-when spider_net_poll() is called, it calls netif_rx_complete() which
causes BUG_ON() because __LINK_STATE_RX_SCHED is not set.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 3cSOHO100-TX needs a mdio_sync() before mdio_read() to read the MII
transceiver registers properly. Adding EXTRA_PREAMBLE to drv_flags of the
3cSOHO100-TX will force this.
This problem exists already for years (I checked back to 2.6.8).
Setting duplex for the 3cSOHO100-TX was more or less a random process.
Till 2.6.15 it was more likely that the diver ends up in half
duplex mode, after the code change in 2.6.16 it was more likely
to end up in full duplex mode. I wonder why nobody noticed this earier.
Hopefully addresses
Bug 7454 3c59x (3cSOHO100-TX Hurricane) slow network bug
http://bugzilla.kernel.org/show_bug.cgi?id=7454
and
Bug 3654 3cSOHO100-TX: No MII transceiver present
http://bugzilla.kernel.org/show_bug.cgi?id=3654
Cc: Jonas Sandberg <jonassa@gmail.com>
Cc: Jon Sanchez <bugs@niluje.net>
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Michael Chan