The NIU device refuses to allow accesses to MSI-X registers before MSI-X
is enabled. This patch fixes the problem by moving the read of the mask
register to after MSI-X is enabled.
Reported-by: David S. Miller <davem@davemloft.net>
Tested-by: David S. Miller <davem@davemloft.net>
Reviewed-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PAGE_MASK is 0xFFFFF000 on i386 -- even with PAE.
So it's not sufficient to ensure that you use phys_addr_t or uint64_t
everywhere you handle physical addresses -- you also have to avoid using
the construct 'addr & PAGE_MASK', because that will strip the high 32
bits of the address.
This patch avoids that problem by using PHYSICAL_PAGE_MASK instead of
PAGE_MASK where appropriate. It leaves '& PAGE_MASK' in a few instances
that don't matter -- where it's being used on the virtual bus addresses
we're dishing out, which are 32-bit anyway.
Since PHYSICAL_PAGE_MASK is not present on other architectures, we have
to define it (to PAGE_MASK) if it's not already defined.
Maybe it would be better just to fix PAGE_MASK for i386/PAE?
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current quirk doesn't include all 82576 device IDs. This update
resolves that.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an upstream port reports an AER error to root port, kernel
starts error recovery procedures. The default return value of
function pcie_portdrv_slot_reset is PCI_ERS_RESULT_NONE. If all
port service drivers of the downstream port under the upstream
port have no slot_reset method in pci_error_handlers, AER recovery
would stop without resume. Below patch against 2.6.30-rc3 fixes it.
Signed-off-by: Zhang Yanmin <yanmin.zhang@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCIe 1.1 base neither requires the endpoint to implement the entire
PCIe capability structure nor specifies default values of registers
that are not implemented by the device. So we only save and restore
registers that must be implemented by different device types if the
device PCIe capability version is 1.
PCIe 1.1 Capability Structure Expansion ECN and PCIe 2.0 requires
all registers in the PCIe capability to be either implemented or
hardwired to 0. Their PCIe capability version is 2.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add drivers/pci/*.c source files to DocBook/kernel-api.tmpl
and update those pci/*.c source files that need kernel-doc fixes.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 30a18d6c3f introduced a new
function to set the PCI bus resources. Unfortunately, neither the
author, nor the committers seemed to know that we already have somewhere
to do that -- pcibios_fixup_bus(). This patch moves the hook (used only
by the K8 code) into x86-specific code where it should have been in the
first place.
Cc: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Without this patch, Broadcom BCM5906 Ethernet controllers set up via MSI
cause the machine to hang. Tejun agreed that the best is to blacklist
the whole chipset and after adding it, seeing the other VIA quirks
disabling MSI, this very much looks like the right way.
Cc: <stable@kernel.org>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If the BIOS does something obviously stupid, like claiming that the
registers for the IOMMU are at physical address zero, then print a nasty
message and abort, rather than trying to set up the IOMMU and then later
panicking.
It's becoming more and more obvious that trusting this stuff to the BIOS
was a mistake.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This issue was pointed out by Linus.
In dma_pte_clear_range() in intel-iommu.c
start = PAGE_ALIGN(start);
end &= PAGE_MASK;
npages = (end - start) / VTD_PAGE_SIZE;
In partial page case, start could be bigger than end and npages will be
negative.
Currently the issue doesn't show up as a real bug in because start and
end have been aligned to page boundary already by all callers. So the
issue has been hidden. But it is dangerous programming practice.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix this build error:
drivers/pci/intr_remapping.c: In function 'ir_parse_ioapic_scope':
drivers/pci/intr_remapping.c:617: error: invalid use of undefined type
'struct acpi_dmar_hardware_unit'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
It's possible for a device in the drhd->devices[] array to be NULL if
it wasn't found at boot time, which means we have to check for that
case.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If a logical hot unplug (remove) is performed on a bridge claimed
by acpiphp and then acpiphp is unloaded, we will encounter an oops.
This is because acpiphp will access the bridge's subordinate bus,
which was released by the user's prior hot unplug.
The solution is to grab a reference on the subordinate PCI bus.
This will prevent the bus from release until acpiphp is unloaded.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reported-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is no reason to prevent removal of root bus devices. A subsequent
rescan will find them just fine.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch fixes breakage of of enable_cnt in quirk_resource_alignment.
Currently, quirk_resource_alignment calls pci_disable_device.
pci_disable_device decrements enable_cnt, so that enable_cnt becomes -1.
The patch disables memory decoding, writing command register directly.
So enable_cnt is not broken.
Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_rescan_bus was annotated as __devinit, which is wrong,
because it will never be part of device initialization.
Howevever, we can't simply drop the annotation, because then we
get section warnings about calling pci_scan_child_bus (which is
correctly marked as __devinit).
pci_rescan_bus will only get built when CONFIG_HOTPLUG is set,
meaning that __devinit is a nop, so we know that pci_scan_child_bus
has not been freed.
Annotate as __ref to silence modpost.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix PCI iov kernel-doc warning:
Warning(drivers/pci/iov.c:638): No description found for parameter 'nr_virtfn'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch sets up disabled bridges even if buses have already been
added.
pci_assign_unassigned_resources is called after buses are added.
pci_assign_unassigned_resources calls pci_bus_assign_resources.
pci_bus_assign_resources calls pci_setup_bridge to configure BARs of
bridges.
Currently pci_setup_bridge returns immediately if the bus have already
been added. So pci_assign_unassigned_resources can't configure BARs of
bridges that were added in a disabled state; this patch fixes the issue.
On logical hot-add, we need to prevent the kernel from re-initializing
bridges that have already been initialized. To achieve this,
pci_setup_bridge returns immediately if the bridge have already been
enabled.
We don't need to check whether the specified bus is a root bus or not.
pci_setup_bridge is not called on a root bus, because a root bus does
not have a bridge.
The patch adds a new helper function, pci_is_enabled. I made the
function name similar to pci_is_managed. The codes which use
enable_cnt directly are changed to use pci_is_enabled.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If BIOS doesn't allocate resources for the SR-IOV BARs, zero the Flash
BAR and program the SR-IOV BARs to use the old Flash Memory Space.
Please refer to Intel 82576 Gigabit Ethernet Controller Datasheet
section 7.9.2.14.2 for details.
http://download.intel.com/design/network/datashts/82576_Datasheet.pdf
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We were comparing {bus,devfn} and assuming that a match meant it was the
same device. It doesn't -- the same {bus,devfn} can exist in
multiple PCI domains. Include domain number in device identification
(and call it 'segment' in most places, because there's already a lot of
references to 'domain' which means something else, and this code is
infected with ACPI thinking already).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When the DMAR table identifies that a PCI-PCI bridge belongs to a given
IOMMU, that means that the bridge and all devices behind it should be
associated with the IOMMU. Not just the bridge itself.
This fixes the device_to_iommu() function accordingly.
(It's broken if you have the same PCI bus numbers in multiple domains,
but this function was always broken in that way; I'll be dealing with
that later).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
interrupt remapping must be enabled before enabling x2apic, but
interrupt remapping doesn't depend on x2apic, it can be used
separately. Enable interrupt remapping in init_dmars even x2apic
is not supported.
[dwmw2: Update Kconfig accordingly, fix build with INTR_REMAP && !X2APIC]
Signed-off-by: Weidong Han <weidong.han@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If queue invalidation is disabled after it's already initialized,
dmar_enable_qi won't re-enable it due to iommu->qi is allocated.
It may result in system hang when use queue invalidation. Add this
check to avoid this case.
Signed-off-by: Weidong Han <weidong.han@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When extended interrupt mode (x2apic mode) is not supported in a
system, it must set compatibility format interrupt to bypass
interrupt remapping, otherwise compatibility format interrupts
will be blocked.
This will be used when interrupt remapping is enabled while x2apic
is not supported.
Signed-off-by: Weidong Han <weidong.han@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch enables suspend/resume for interrupt remapping. During suspend,
interrupt remapping is disabled. When resume, interrupt remapping is enabled
again.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch implements the suspend and resume feature for Intel IOMMU
DMAR. It hooks to kernel suspend and resume interface. When suspend happens, it
saves necessary hardware registers. When resume happens, it restores the
registers and restarts IOMMU by enabling translation, setting up root entry, and
re-enabling queued invalidation.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If the device is not supposed to wake up the system, ie. when
device_may_wakeup(&dev->dev) returns 'false', pci_prepare_to_sleep()
should pass 'false' to pci_enable_wake() so that it calls the
platform to disable the wake-up capability of the device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The radeonfb driver needs to program the device's PMCSR directly due
to some quirky hardware it has to handle (see
http://bugzilla.kernel.org/show_bug.cgi?id=12846 for details) and
after doing that it needs to call the platform (usually ACPI) to
finish the power transition of the device. Currently it uses
pci_set_power_state() for this purpose, however making a specific
assumption about the internal behavior of this function, which has
changed recently so that this assumption is no longer satisfied.
For this reason, introduce __pci_complete_power_transition() that may
be called by the radeonfb driver to complete the power transition of
the device. For symmetry, introduce __pci_start_power_transition().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
At present the configuration spaces of PCI devices that have no
drivers or no PM support in the drivers (either legacy or through a
pm object) are not saved during suspend and, consequently, they are
not restored during resume. This generally may lead to the state of
the system being slightly inconsistent after the resume, so it's
better to save and restore the configuration spaces of these devices
as well.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is a problem with PCI devices without any PM support (either
native or through the platform) that pci_set_power_state() always
returns error code for them, even if they are being put into D0.
However, such devices are always in D0, so pci_set_power_state()
should return success when attempting to put such a device into D0.
It also should update the current_state field for these devices as
appropriate. This modification is necessary so that the standard
configuration registers of these devices are successfully restored by
pci_restore_standard_config() during the "early" phase of resume.
In addition, pci_set_power_state() should check the value of
current_state before calling the platform to change the power state
of the device to avoid doing that unnecessarily.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Once we have allowed timer interrupts to be enabled during the late
phase of suspending devices, we are now able to use the generic
pci_set_power_state() to put PCI devices into low power states at
that time. We can also use some related platform callbacks, like the
ones preparing devices for wake-up, during the late suspend.
Doing this will allow us to avoid the race condition where a device
using shared interrupts is put into a low power state with interrupts
enabled and then an interrupt (for another device) comes in and
confuses its driver. At the same time, devices that don't support
the native PCI PM or that require some additional, platform-specific
operations to be carried out to put them into low power states will
be handled as appropriate.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move pci_restore_standard_config() from pci.c to pci-driver.c and
make it static.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Once we have allowed timer interrupts to be enabled during the early
phase of resuming devices, we are now able to use the generic
pci_set_power_state() to put PCI devices into D0 at that time. Then,
the platform-specific PM code will have a chance to handle devices
that don't implement the native PCI PM or that require some
additional, platform-specific operations to be carried out to power
them up. Also, by doing this we can simplify the code quite a bit.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I noticed two functions use a variable "i" to store the return value of PM
function calls while the rest of the file uses "error". As "i" normally
indicates a counter of some sort it seems better to keep this consistent.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Impact: fix bug
This patch reworks the nv_msi_ht_cap_quirk() and will only try to avoid
to enable ht_msi on device following that root dev, and don't touch that
root dev, but only do that trick with end_device on the chain.
Reported-by: Prakash Punnoor <prakash@punnoor.de>
Tested-by: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Impact: fix bug
Prakash reported that his c51-mcp51 system ondie sound card doesn't work
MSI but if he hack out the HT-MSI on mcp51, the MSI will work well with
sound card.
This patch reworks nv_msi_ht_cap_quirk() and will only avoid enabling
ht_msi on devices following that root device.
Reported-by: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCIe 2.0 defines several new registers (Device Control 2, Link Control 2,
and Slot Control 2). Save and retore them in pci_save_pcie_state() and
pci_restore_pcie_state().
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Get rid of a new use of bus_id that snuck in.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
New pci_cfg_space_size() needs invalid pdev->class, put it in the
right place in the pci_setup_device().
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add new flags in the Boot Architecture flags field. Update comments
for all FADT flags. Add FADT version when each flag was defined.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The problem is in dma_pte_clear_range and dma_pte_free_pagetable. When
intel_unmap_single and intel_unmap_sg call them, the end address may be
zero if the 'start_addr + size' rounds up. So no PTE gets cleared. The
uncleared PTE fires the BUG_ON when it's used again to create new mappings.
After I modified dma_pte_clear_range a bit, the BUG_ON is gone.
Tested both 32 and 32 PAE modes on Intel X58 and Q35 platforms.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If we fix a few highmem-related thinkos and a couple of printk format
warnings, the Intel IOMMU driver works fine in a 32-bit kernel.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Matthew Wilcox