Use EXPORT_SYMBOL_GPL for new symbols, and declare the struct in the header
file for access by other modules.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes a needlessly global variable static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- rename EXPORTed gpio vtables from {scx200,pc8736x}_access to _gpio_ops new
name is much closer to the vtable-name struct nsc_gpio_ops, should be
clearer. Also rename the _fops vtable var to _fileops to better
disambiguate it from the gpio vtable.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drops gpio_set_high, gpio_set_low from the nsc_gpio_ops vtable. While we
can't drop them from scx200_gpio (or can we?), we dont need them for new users
of the exported vtable; gpio_set(1), gpio_set(0) work fine.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the scx200_gpio's cdev-array & ksalloc, replacing it with a single
static struct cdev, which is sufficient for all the pins.
cdev_put is commented out since kernel wont link properly with it, and its
apparently not needed.
With these patches, this driver continues to work with Chris Boot's
leds_48xx driver.
Signed-off-by Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this patch is mostly cleanup of scx200_gpio :
- drop #include <linux/config.h>
- s/DEVNAME/DRVNAME/ apparently a convention
- replace variable num_pins with #define MAX_PINS
- s/dev/devid/ to clarify that its a dev_t, not a struct device dev.
- move devid = MKDEV(major,0) into branch where its needed.
2 minor 'changes' :
- reduced MAX_PINS from 64 to 32. Ive never tested other pins, and
theyre all multiplexed with other functions, some of which may be in use
on my soekris 4801, so I dont know what testing should yield.
- +EXPORT_SYMBOL(scx200_access);
This exposes the driver's vtable, which another driver can use along
with #include <linux/nsc_gpio.h>, to manipulate a gpio-pin.
Signed-off-by Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mark the static struct file_operations in drivers/char as const. Making
them const prevents accidental bugs, and moves them to the .rodata section
so that they no longer do any false sharing; in addition with the proper
debug option they are then protected against corruption..
[akpm@osdl.org: build fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes drivers/char/pc8736x_gpio.c and drivers/char/scx200_gpio.c to
use the platform_device_del/put ops correctly.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use of dev_dbg() and friends is considered good practice. dev_dbg() needs a
struct device *devp, but nsc_gpio is only a helper module, so it doesnt
have/need its own. To provide devp to the user-modules (scx200 & pc8736x
_gpio), we add it to the vtable, and set it during init.
Also squeeze nsc_gpio_dump()'s format a little.
[ 199.259879] pc8736x_gpio.0: io09: 0x0044 TS OD PUE EDGE LO DEBOUNCE
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since the meaning of config-bits is the same for scx200 and pc8736x _gpios, we
can share a function to deliver this to user. Since it is called via the
vtable, its also completely replaceable. For now, we keep using printk...
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that the read(), write() file-ops are dispatching gpio-ops via the vtable,
they are generic, and can be moved 'verbatim' to the nsc_gpio common-support
module. After the move, various symbols are renamed to update 'scx200_' to
'nsc_', and headers are adjusted accordingly.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now actually call the gpio operations thru the vtable.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Abstract the gpio operations into a new nsc_gpio_ops vtable.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new driver command: 'v' which calls gpio_dump() on the pin. The output
goes to the log, like all other INFO messages in the original driver. Giving
the user control over the feedback they 'need' is construed to be a
user-friendly feature, and allows us (later) to dial down many INFO messages
to DEBUG log-level.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a platform-device to scx200_gpio, and use its struct device dev member
(ie: devp) in dev_dbg() once.
There are 2 alternatives here (Im soliciting guidance/commentary):
- use isa_device, if/when its added to the kernel.
- alter scx200.c to EXPORT_GPL its private devp so that both scx200_gpio,
and the (to be added) nsc_gpio module can use it. Since the available devp
is in 'grandparent', this seems like too much 'action at a distance'.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adopt many modern 2.6 coding practices, ala LDD3, chapter 3. Changes are
limited to initialization calls from module init, ie: cdev_init, cdev_add,
*_chrdev_region, mkdev.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
GPIO SUPPORT FOR SCx200 & PC8736x
The patch-set reworks the 2.4 vintage scx200_gpio driver for modern 2.6, and
refactors GPIO support to reuse it in a new driver for the GPIO on PC-8736x
chips. Its handy for the Soekris.com net-4801, which has both chips.
These patches have been seen recently on Kernel-Mentors, and then
Kernel-Newbies ML, where Jesper Juhl kindly reviewed it. His feedback has
been incorporated. Thanks Jesper !
Its also gone to soekris-tech@soekris.com for possible testing by linux folks,
I've gotten 1 promise so far. Theyre mostly BSD folk over there, but we'll
see..
Device-file & Sysfs
The driver preserves the existing device-file interface, including the
write/cmd set, but adds v to 'view' the pin-settings & configs by inducing,
via gpio_dump(), a dev_info() call. Its a fairly crappy way to get status,
but it sticks to the syslog approach, conservatively.
Allowing users to voluntarily trigger logging is good, it gives them a
familiar way to confirm their app's control & use of the pins, and I've thus
reduced the pin-mode-updates from dev_info to dev_dbg.
I've recently bolted on a proto sysfs interface for both new drivers. Im not
including those patches here; they (the patch + doc-pre-patch) are still quite
raw (and unreviewed on KNML), and since they 'invent' a convention for GPIO, a
proper vetting is needed. Since this patchset is much bigger than my previous
ones, Id like to keep things simpler, and address it 1st, before bolting on
more stuff.
The driver-split
The Geode CPU and the PC-87366 Super-IO chip have GPIO units which share a
common pin-architecture (same pin features, with same bits controlling), but
with different addressing mechanics and port organizations.
The vintage driver expresses the pin capabilities with pin-mode commands
[OoPpTt],etc that change the pin configurations, and since the 2 chips share
pin-arch, we can reuse the read(), write() commands, once the implementation
is suitably adjusted.
The patchset adds a vtable: struct nsc_gpio_ops, to abstract the existing gpio
operations, then adjusts fileops.write() code to invoke operations via that
vtable. Driver specific open()s set private_data to the vtable so its
available for use by write().
The vtable gets the gpio_dump() too, since its user-friendly, and (could be
construed as) part of the current device-file interface. To support use of
dev_dbg() in write() & _dump(), the vtable gets a dev ptr too, set by both
scx200 & pc8736x _gpio drivers.
heres how the pins are presented in syslog:
[ 1890.176223] scx200_gpio.0: io00: 0x0044 TS OD PUE EDGE LO DEBOUNCE
[ 1890.287223] scx200_gpio.0: io01: 0x0003 OE PP PUD EDGE LO
nsc_gpio.c: new file is new home of several file-ops methods, which are
modified to get their vtable from filp->private_data, and use it where needed.
scx200_gpio.c: keeps some of its existing gpio routines, but now wires them up
via the vtable (they're invoked by nsc_gpio.c:nsc_gpio_write() thru this
vtable). A driver-spcific open() initializes filp->private_data with the
vtable.
Once the split is clean, and the scx200_gpio driver is working, we copy and
modify the function and variable names, and rework the access-method bodies
for the different addressing scheme.
Heres a working overview of the patchset:
# series file for GPIO
# Spring Cleaning
gpio-scx/patch.preclean # scripts/Lindent fixes, editor-ctrl comments
# API Modernization
gpio-scx/patch.api26 # what I learned from LDD3
gpio-scx/patch.platform-dev-2 # get pdev, support for dev_dbg()
gpio-scx/patch.unsigned-minor # fix to match std practice
# Debuggability
gpio-scx/patch.dump-diet # shrink gpio_dump()
gpio-scx/patch.viewpins # add new 'command' to call dump()
gpio-scx/patch.init-refactor # pull shadow-register init to sub
# Access-Abstraction (add vtable)
gpio-scx/patch.access-vtable # introduce nsg_gpio_ops vtable, w dump
gpio-scx/patch.vtable-calls # add & use the vtable in scx200_gpio
gpio-scx/patch.nscgpio-shell # add empty driver for common-fops
# move code under abstraction
gpio-scx/patch.migrate-fops # move file-ops methods from scx200_gpio
gpio-scx/patch.common-dump # mv scx200.c:scx200_gpio_dump() to nsc_gpio.c
gpio-scx/patch.add-pc8736x-gpio # add new driver, like old, w chip adapt
# gpio-scx/patch.add-DEBUG # enable all dev_dbg()s
# Cleanups
# finish printk -> dev_dbg() etc
gpio-scx/patch.pdev-pc8736x # new drvr needs pdev too,
gpio-scx/patch.devdbg-nscgpio # add device to 'vtable', use in dev_dbg()
# gpio-scx/patch.pin-config-view # another 'c' 'command'
# gpio-scx/quiet-getset # take out excess dbg stuff (pretty quiet
now)
gpio-scx/patch.shadow-current # imitate scx200_gpio's shadow regs in
pc87*
# post KMentors-post patches ..
gpio-scx/patch.mutexes # use mutexes for config-locks
gpio-scx/patch.viewpins-values # extend dump to obsolete separate 'c' cmd
gpio-scx/patch.kconfig # add stuff for kbuild
# TBC
# combine api26 with pdev, which is just one step.
# merge c&v commands to single do-all-fn
# delay viewpins, dump-diet should also un-ifdef it too.
diff.sys-gpio-rollup-1
This patch:
Removed editor format-control comments, and used scripts/Lindent to clean up
whitespace, then deleted the bogus chunks :-(
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Chris Boot